For more information on our products, visit www.raceland.com.
Пікірлер: 55
@nicholasvantassel44724 жыл бұрын
I have had these on my 250 for a couple years now, going to replace with new ones because they are getting bouncy and they did not do this before. Im just glad you guys offer a life time warranty. Also just a quick tip to anyone getting these, make sure you unplug the ABS sensor on the back of the steering knuckle BEFORE you undo the upper ball joint. The wires will rip out the back and you'll need to replace it.
@brianyt568 ай бұрын
Good note.... thank you for this. I made sure to unplug the ABS sensor and you saved my a$$. Question: after install, i still have these lights on: ABS, Brake, and Traction... Help? THanks man.
@antoniomorales14463 жыл бұрын
I’ve heard so many good things about you guys once I save up money I’m forsure going to buy these for my is250
@southsidebabescrew19122 жыл бұрын
I never knew it looked this easy to replaced or install a new one
@QuanGissle3 жыл бұрын
Before you tighten your bolt, aren’t you suppose to put load on to the suspension before you tighten the bushing? I heard it’ll wear immaturely if you tighten them before you lower the car to the ground
@racelandsuspension3 жыл бұрын
Yes. You'll want to load the suspension before you tighten everything down to spec.
@brianyt568 ай бұрын
this was the best video.. however, after the install, i still have these lights on: ABS, Brake, and Traction... Help? THanks.
@racelandsuspension8 ай бұрын
If you disconnected any electronic systems during the install, that would be the culprit.
@Southboundsociety3 жыл бұрын
I wish you guys had a set that for the awd😢
@greg07164 жыл бұрын
do i need to let the coilovers settle before i get an alignment?
@racelandsuspension4 жыл бұрын
Yeah. That should only take a day or two to settle.
@zahramuradi71044 жыл бұрын
0:50 I can’t take the bolt off it’s so hard I tried and hammer it I’d didn’t work
@racelandsuspension4 жыл бұрын
Soak it in a penetration oil like PB Blaster and let it sit for several hours.
@fawadmoradi44024 жыл бұрын
Nah that is not gonna help as well I try putting WD40 and keep hitting them it didn’t work
@vursce4 жыл бұрын
Use a drill, put on an attachable nut to the drill, and the needed socket and try it, it wont be strong as an air gun but it might work
@xo4r4 жыл бұрын
pitman arm puller
@808G8GT3 жыл бұрын
@@fawadmoradi4402 PB Blaster is FAR superior to WD40 for frozen bolts. After discovering PB Blaster....I will NEVER buy wd40 again.
@yordyjara2 жыл бұрын
I have a 2015 Lexus IS 250... but you guys only offer till 2013... Am I still able to purchase the coil overs for my vehicle?
@racelandsuspension2 жыл бұрын
We apologize for the trouble, but we don't offer anything for that model year.
@jamez3x2 жыл бұрын
Next purchase!
@Ericcoronel542 жыл бұрын
Is this for the Lexus is250 2014 and up or the older gens???? Please let me know
@racelandsuspension2 жыл бұрын
This is for the '06-13 IS250 models.
@rkeow2 жыл бұрын
Just bought a set, I was wondering if you have the torque specs for all the rear nuts
@racelandsuspension2 жыл бұрын
They are just the stock torque specs.
@yiihn6 жыл бұрын
Are these suitable for daily driving?
@racelandsuspension6 жыл бұрын
Yes. We designed them for a daily driver.
@Cloud_36395 жыл бұрын
what model lexus is that
@MRogerFTW5 жыл бұрын
Serey Tu is250/350
@jimb45472 жыл бұрын
Is this an all wheel drive is250? If not will the install be the same ? Thanks
@racelandsuspension2 жыл бұрын
This is for the two wheel drive models. We haven't had the chance to run fitment on the AWD, so we wouldn't be able to confirm if the install is the same.
@tasshuffler89057 жыл бұрын
Are you using jacks to hold up the whole assembly when doing this process? Or is it not necessary? Can't tell in this vid
@racelandsuspension7 жыл бұрын
Let me know at what time mark in the video that you are referring to and we'll let you know.
@orlandosanchez1795 жыл бұрын
The rear assembly looked like they had some sort of support. I use a tranny jack in my shop for that sort of r&r
@NamTran-hh4hn5 жыл бұрын
Do you have to alignment after you installed?
@racelandsuspension5 жыл бұрын
Yes. We highly suggest that you have the car aligned after you install the coilovers.
@darrkitx116 жыл бұрын
is there a difference between AWD and RWD ?
@adynread14013 жыл бұрын
Seven
@dannyturner79674 жыл бұрын
I recommend soaking your nuts in pb blaster for 1 to 2 weeks ahead of any repair just randomly spray your nuts with pb blaster for a week or two leading up to the repair....it works. Nuts and bolts...lol sorry
@MrSodapop915 жыл бұрын
Masterful!!
@zahramuradi71044 жыл бұрын
Isaiah Sims hey do you know how to take that bolt of I tried but couldn’t and I tried and hammer it as well 0:50
@alangarcia11613 жыл бұрын
How much do you preload the coilovers for this car?
@racelandsuspension3 жыл бұрын
We recommend no more than 5mm of preload.
@lachlanl22447 жыл бұрын
thank you!!!!!!!!
@jacobromero3694 Жыл бұрын
Was this an awd or rwd model?
@racelandsuspension Жыл бұрын
This is for the RWD models.
@lajlijthoj7 жыл бұрын
Is there a coilover for the AWD model?
@racelandsuspension7 жыл бұрын
I'm sorry but we don't offer a kit for the AWD models.
@lee17787305 жыл бұрын
fit a ISF? need a temp
@racelandsuspension5 жыл бұрын
Unfortunately, this kit will not fit the ISF. Sorry :/
@RonDaG0at3 ай бұрын
It’s that easy?
@racelandsuspension3 ай бұрын
Assuming all 10+ year old bolts come out like they should. 🤣
@RLTPDX4 жыл бұрын
IS250 AWD ?
@racelandsuspension4 жыл бұрын
Sorry. We don't offer anything for the AWD models.