Mercedes Benz CPS (Crankshaft Position Sensor)

Mercedes Benz CPS (Crankshaft Position Sensor) M119 Engine R129 SL500
#mercedes
#benz
#r129
#sl
#slclass

[@danludwig3679]

Thank you my friend. Your videos are excellent and help very much. 👍🏼

[@BenzAddiction]

Thanks Ludwig

[@douglasthompson9482]

Thank you for your help. There is a huge difference between original and aftermarket parts for some Mercedes

[@BenzAddiction]

You are welcome, sure there is...

[@douglasthompson9482]

My warm cps will not start but started when it was cold. In fact the construction of the new cps is poor. There is an insert that fell out from the housing for the bolt support. I will now buy a original mb cps… end of story.

[@BenzAddiction]

@@douglasthompson9482 kzbin.info/www/bejne/p6KUm4Kvo7isntU

[@keeponcruisin7876]

Sweet!! I just ordered a cps and from experience on an M104 knew they hide em on the bellhousing. Where exactly was the guess. Thanks for showing!! New cam ps, new caps, new motor mount all on the way. New plugs n plug wires, oil change, air filters, new upper radiator hose so far.

[@BenzAddiction]

Good luck 👍

[@samuelberkun9788]

this fixed my 95 SL500, car would die when it got hot, was relieved, easy fix.

[@BenzAddiction]

Glad it helped :)

[@Elnur05282]

Excellent instruction 👍🏽👍🏽

[@BenzAddiction]

Thanks for Watching:)

[@tramptruck4859]

Excellent video. I have occasional hot start reluctance, and 150k miles. I think I need to check this out!

[@BenzAddiction]

Hi mate, it is really easy to check this using a multimeter and replacing is part of preventive maintenance...

[@BenzAddiction]

Sometimes we miss the distributor caps and Rotors, these can also cause the same symptoms...

[@tramptruck4859]

@@BenzAddiction I had good start from cold, but after running for a short while and stopping it was hard to start and very rough. Distributor caps were wet inside. I changed the o rings on the dust covers - no problems since 👍

[@tramptruck4859]

Checked mine this morning - 800ohms cold and 950 warm, ambient is about 5*C here so it would get warmer come summer.

[@BenzAddiction]

@tramptruck4859 not that bad actually, did you watch my recent video on how I fixed the Hesitation Issue? kzbin.info/www/bejne/p6KUm4Kvo7isntU

[@m.rehanul-haq9710]

Where is a part 2 for this video. my car shakes a bit but no warnings. how is rmp on your car now and how was it before?

[@BenzAddiction]

There is no part 2.

[@Maybe1Someday]

Did your car throw a code for this. Mine had a "crankshaft" code that can clear and also a "ignition system fault" code that will not clear

[@BenzAddiction]

I had no lights on, I finally replaced the cps but did not improve any thing. I was unable to get any code of the ECU with star C3 or the other one, now has Hesitation mid RPM, I have ordered ignition distributor caps...

[@caleb6534]

A rodent chewed this wire on my 600SEL. I have a replacement OEM. However, I cannot see the location of that sensor because the engine is much bigger. Have you ever had to work on a 600 in the same capacity?

[@BenzAddiction]

Hi Caleb, maybe you need to buy a cheap endoscope from Ebay and run it behind the engine and find the sensor. From there you can find the easiest access to run tools to take off the 10mm screw.

[@caleb6534]

@@BenzAddiction I see! Do you know if it’s possible to repair a damaged wire or is it impossible to the get the same resistance if you solder it back together?

[@adek330Ci]

👍

[@BenzAddiction]

Thanks mate ;)

[@rioraton]

So, i have a 92 500sl. hard start rough idle. have a blink code reader. Tested port 8 it showed DTC # 17 Crankshaft position sensor faulty. Cleared code started car rechecked port 8 DTC #17 again. 2 questions: should I still test with multimeter too? also how in the hell did you route the wire it looks like it goes under the manifold? I can not see how the wire runs.

[@BenzAddiction]

Hello, testing the cps is easy with multimeter and you don't need to remove the sensor and is recommended. Other major M119 issue is Distributor caps + Rotors that most people keep replacing them as early as 20k miles, inspect them of there is black sooth inside, they are bad.

[@rioraton]

@@BenzAddiction OK, so i tested it cold 68.5 f on block and it was 845? what do you think

[@BenzAddiction]

@@rioraton I think you have a good CPS, how old are your distributor caps and Rotors?

[@rioraton]

@@BenzAddiction you are CORRECT. What I found out with the car OFF testing port 8 will ALWAYS show a DTC #17. Dont ask why cuz I do not know? You have to test this port with the car running which I did and NO fault codes were detected. Also, if I turn ignition on/off and on/off again THEN start the car it starts right up?? I may have a bad accumulator where the diaphragm is causing me to loose fuel pressure and by re-pressuring the system with on off on off might be why it starts right up? More investigation needs to be done these cars are a REAL pain to trouble shoot??

[@BenzAddiction]

@@rioraton agreed M119 engine is not DIY Diagnostic friendly, I have a video on fuel Pressure and regulator... kzbin.info/www/bejne/gJOsY4h9atdkkJY