Mercedes W203 (M271) On The Dyno | Torque Tuning | More POWER!!!+++

[@tareqchallah309]

From 105 kw to 130 kw 👍🏻👍🏻👍🏻 I can see that you studied the car very well before modifying it.

[@sales2791]

Pop and Bangs sounds amazing, love it....

[@RicerBenz]

sales 2 thanks for the positive comment!🙏😁

[@LucasLeal96]

Very good results, love those pops and bangs!

[@RicerBenz]

Lucas Leal thanks for the positive comment😁😁😁honestly I enjoy it too!! Need a bigger exhaust. I want flames 🔥 lol!

[@m3up_737]

@@RicerBenzhow long have you been driving the car with that Power? How did the oil look, after the first change?

[@sphephelondimande1325]

I have a W203 C180 as well, what exhaust mods are you running. Or did you have the cats removed and how much did you spend for the smaller pulley

[@diona.2076]

Hello my friend, did you have the setting DYNOMODE on from the front screen enabled through the triple contrast button click while dyno?

[@RicerBenz]

Yes I did😁🙏🏻

[@federikg]

Amazing job ! Can I ask you where you purchased the small pulley ?

[@RicerBenz]

Thanks man! I had one made. (Engineer with a lathe)✌🏻💪🏼😁

[@c1house]

There was a company on eBay called IBF that sold a 65MM pully. I was lucky enough to import one to SA before they disappeared of eBay.There is another german company that still sells them I will try and find the link to them

[@georgec.2638]

Last I seen a company called Moscow supercharged still sold some for the m271

[@Hilmaror]

Love the w203 its so fun to just toss around

[@RicerBenz]

😁😁😁

[@thepio14343SWEG]

Agreed however when the chain starts to rattle, so does your mind 😭😂😂

[@eczmurat]

great gains! what octane fuel do you use before and after?

[@RicerBenz]

Thanks man! We get 93 and 95 here. So I just always go for 95👌😁

[@eczmurat]

@@RicerBenz RON95 ? Wow. And you had no knock problems over boosting an m271 with 10.2 compression ratio? I own a m111 2.0 with 9.5 and knock sensor pull timing if I go above 7 psi boost with 95 fuel.

[@RicerBenz]

@@eczmurat aaah m111👌😎 it seemed fine to me but not enough power🤪 so I pulled the m271 engine and now have a m104 I’m working on😁

[@jtsn667]

I'm doing a turbo swap and am struggling with the ecu and injectors... Any advice?

[@RicerBenz]

Oh wow👌I’ve also thought about that😁would love to see?? I’m still on stock injectors and just had the ecu mapped because of the more boost. If I’m not mistaken you’ll have to change the ecu🙈 Because the supercharger has boost from the start And with a turbo boost will come in at a certain rev and then the ecu will have to add fuel at that point. Hope that helps.

[@blownxy]

I'd like to see that conversion! Best to go a full aftermarket ecu for the car if you want to unlock all it can do. I'm looking for programs to decode the stock ecu but pretty much nothing out there (I'm still looking). found online tuner companies that can do maps for you so long as you can extract the base map and send the file, then you got to flash your ecu....bit risky. BTW what motor do you have in your Merc, Shivam Chand ?

[@RicerBenz]

Thanks for the advice man😎I’m also looking into the standalone or something and then later maybe turbo. Then it shoul be easy. Just soooo expensive 🤣🙈 I have the M271 engine.

[@angelcividanes7146]

Woo doo i need to do this to my c280 1999 . good wrok on your car and bless your car 👍🏻😂😇😳🏁🤘

[@oscarbaruch6984]

I tried to change the pulley on my C180k to a smaller one, but , there was no way to remove it by any kind of method... and i tried many times...Finally i remaped the ECU and i get 12CV extra and after i have changed the signal from the air sensor to lower (V) and i have get another extra of 15CV and 40 Nm. I wish that i could remove also the pulley. Saludos

[@RicerBenz]

I took the whole supercharger to the guy that made my pulley. Not sure how he got it off🤣 It sounds like you have a ecu guy that knows his stuff and respect to those signal tricks😁😁😁I would also love if you could add the smaller pulley for even more gains!!😁💪🏼

[@oscarbaruch6984]

@@RicerBenz yea and more since i bought the pulley from Russia xd and it cost me 220€ ... About the signal tricks, i can tell you how , it is not so expensive. Saludosss

[@RicerBenz]

@@oscarbaruch6984 thanks man! Would have loved to try but I have a different engine in it now😁

[@oscarbaruch6984]

@@RicerBenz will work anyway xd trust me

[@mygoalcrash8077]

Hello Oscar .Can you tell more about signal to air sensor mode? I need more hp for my 1.8k 😀.thanks

[@Georgealex77]

Im actually thinking of swapping a M111 2.3 into my W209 CLK200, you heard any similar swaps by any chance?

[@RicerBenz]

Can’t think that I have. Sounds like a great idea🤙🏼 M111 engine’s are very similar to the M104.

[@hwalimadigital4200]

Amazing i have a W203 C180 Kompressor... i need the same done to it. Where can i reach you?

[@RicerBenz]

I did the ECU stuff at Jnes Tuned in Potchefstroom. Or you can DM me on instagram @ricer_benz.✌🏻

[@simrandhillon7684]

Good i also gonna go now for dyno... i have c200 kompressor...

[@giannistsilikiotis]

Pop and bangs are amazing can i have to my car? I have eclass w211 m271 engine i waaant pops!!

[@RicerBenz]

Lol yeah it’s possible😁😎you just need to find someone in your area that can get into the software on the ECU👌

[@giannistsilikiotis]

@@RicerBenz nobody knows can you contact with you? To help me or send me this file?

[@RicerBenz]

@@giannistsilikiotis I don’t have the file and can’t gain access to it. I took it to a place here in South Africa and the guy did everything for me.

[@giannistsilikiotis]

@@RicerBenz can you send me the email of this guy? Or something?

[@RicerBenz]

@@giannistsilikiotis are you from SA? Would you be able to bring the car to Potchefstroom in North West province?

[@SeanParker-b8n]

How’d you get the pops and bangs tuned

[@AP77432]

I dont think u needed smaller sc pulley, i mean for 130 kw would be enough stock pulley size, because via ecu you can fully close bypass valve at higher rpm and gain arround 3 PSI, which equals in about 20% increase in power. M271 engines have protection, thay controls maximum boost levels arround 5k rpm and higher.... Your fuel system was maxed out or combustion temps very high i think, so they pushed only +25 kw? They didnt said for you anything about that?

[@youssefzaiter722]

Please keep doing Video about this car it's beautiful

[@RicerBenz]

Haha thanks man will do!😁🙏

[@bilalcassim4509]

Howsit ? Where did you get the bigger pulley and bigger intercooler ?looking to do the same

[@RicerBenz]

Hi man. I got the smaller pulley made by a local engineer. Had to remove the supercharger and take it to them for a couple of days. Intercooler I bought online @ Mr Turbo😁

[@mangochampagnelasssi9028]

What type of parts do you need installed in the Mercedes c230 konpressor sport sedan. For this tuning ? I’m a bit new to all this. I’m trying to finish my car up looks wise it’s almost done. But the engine parts and stuff I want to get it tuned but I don’t know what things I need to have installed, if anyone can let me know I’d appreciate it

[@RicerBenz]

With my experience Now I would just do a smaller pulley (Just get any engineer with a lathe and some imagination 😁👌) I didn’t even need a new belt.Then get someone that can adjust the software. The reason I replaced the intercooler was more just for the look. The C230 should see some decent gains😁💪goodluck!

[@mangochampagnelasssi9028]

Okay I’ll definitely get to that. I’m right now trying to get this engine light off. I think it’s the spark plugs and the coils I gotta change those cus when I bought it I didn’t and now it’s not giving me enough power. When I even slightly tap the pedal it has alot of resistance

[@mangochampagnelasssi9028]

If I could I’d show you the interior work I’ve done

[@arturaspf2566]

Do you do this dyno runs with closed bypass valve with that custom plate?

[@RicerBenz]

No I changed it back. Car runs poorly with that plate at partial throttle. Full throttle it’s a beast👌🤣🤣

[@arturaspf2566]

@@RicerBenz do you tested on dyno before mods, how healthy car power was? ☺️

[@RicerBenz]

@@arturaspf2566 unfortunately not.

[@arturaspf2566]

@@RicerBenz oh.. I think with colder spark plugs final dyno could be better slightly :) Do airbox was strictive that you remove? Hot air looks not nice for me ;)

[@RicerBenz]

@@arturaspf2566 no the stock airbox would be better than what I did. It just looked nice🤣

[@593432223]

when you moved to m104 was the wiring fairly easy ?

[@RicerBenz]

Yes BUT I had to offer up working gauges and use a stand alone engine management

[@tymichaelis9735]

How much did the tune cost? I’m just curious cause I would love to do something like that to my car, it’s a very similar model.

[@RicerBenz]

Back then it was R3500. That was for mapping with the smaller pulley and pops & bangs tune✌️

[@mygoalcrash8077]

@@RicerBenz maping how much?

[@RicerBenz]

@@mygoalcrash8077 R3500 back then. Should be cheaper now

[@mygoalcrash8077]

@@RicerBenz 3500 dollars? Wow alot money

[@RicerBenz]

@@mygoalcrash8077 nooo🤣 rand. I’m in South Africa

[@jdmcars9512]

What program do I use to tune the ecu?

[@RicerBenz]

JDM Cars I have no idea how they do it🙈that’s why I took it to this place😁👌

[@jdmcars9512]

@@RicerBenz If you can ask them and tell me what program they used, you would help me a lot !! thanks

[@twincheesetowers]

Buy a Galletto cable online, you can pull the file off the ecu with that. And then to modify the file is a longer story.

[@Goldsalltime]

can someone agree with me that this is south africa to the world

[@lyshing1144]

How can do pop and bang on my wM271 bro 🎉❤

[@unikron9092]

How’d you do it? No one in florida said they can tune my 2006 Mercedes c230 sport

[@RicerBenz]

Sorry to hear that man. I found someone very close to me that was able to remap it. Not sure what or how they do it. Goodluck!

[@athenadanielsooloom4939]

Can I get a burple tune and a turbo on my c280

[@ThanosStrongmanGG]

Hello from Greece! I have the same car 210hp in 1.1 bar

[@RicerBenz]

Oh yessss💪🏼😁😁😁

[@mygoalcrash8077]

Turbo? 1.8 kompressor?

[@ThanosStrongmanGG]

@@mygoalcrash8077 kompressor my friend!

[@mygoalcrash8077]

@@ThanosStrongmanGG can you tel about remap? Small pulley? Is w271 engine?

[@ThanosStrongmanGG]

@@mygoalcrash8077 m271 1800cc full exhaust 63.5, intercooler,small pulley ecu remap for 100ron works in 1.2 pressure!

[@naushrhyman6325]

WHAT ENGINE THE 1.6 OR 1.8 ?

[@simrandhillon7684]

Where did you find that supercharger pulley

[@RicerBenz]

Simran Dhillon I went to a local engineer after removing the sc from the car He pulled of the old pulley and made me a new smaller one😁😁😁

[@simrandhillon7684]

That sucks bruh😇

[@jtsn667]

@@RicerBenz what size he make up?

[@RicerBenz]

@@jtsn667 If I remember correctly it’s 15mm smaller Sorry not sure🙈🙈 But it was the smallest he could make it to still fit over the casing...

[@elijahschool2725]

can you please send the tune?

[@savvasgreece8700]

how many kilometers with m271? cam gears? chain?

[@RicerBenz]

225k😁 Cam gears replaced by previous owner 👌

[@espadasmoran]

dammmm Do you sell your ECU? :D

[@RicerBenz]

Nope I need to have it for al the electronics 😂

[@Abdulsamad-fz7ru]

Where can I find pulleys. I have a w204 c200 kompressor.

[@mercow1242]

I'am thinking to put a m271 to w124 e200. How could it be like? Is that easy to put a m271 place of m111 N/A

[@Raven3one]

holy shit are you telling me my car can sound like that

[@RicerBenz]

Yep😁🤣

[@ZacharySlaver]

I have a 2003 Mercedes c230 Kompressor Sport Coupe 2dr with the m271 1.8l 4cyl engine. How do I make my pops and gurgles sound like yours? Just that supercharger pulley, intercooler, and a stage 1 tune!? Get back to me brother! Nice vid, I subscribed!

[@RicerBenz]

Awesome man No the pops and bangs don’t need the pulley and intercooler That’s all about the tune. I have no idea how they do it. I just took it to a place to get it done😁

[@ZacharySlaver]

@@RicerBenz Dang dude, stock exhaust too? That's crazy, I knew these engines could do those pops! Just didn't know how to. I thought it was the exhaust really. You should get on facebook in a Mercedes c230 kompressor group, a lot of guys would like to see this stuff! Is yours a 1.8l 4cyl?

[@RicerBenz]

Sorry🙈the exhaust is just “straight” piped. Cat delete 1 x resenator and 1 small silencer. I’ll have a look thanks man😁

[@RicerBenz]

Yep they all have the same m271 engines just different ecu, piston and supercharger arrangements 😁

[@ZacharySlaver]

@@RicerBenz What are you pushing for hp now bro? The metric system is different here in the US.

[@TheAbu420]

Does the w204 pre facelift c class also have same engine??

[@RicerBenz]

I’m pretty sure it’s the same yes👌

[@TheAbu420]

@@RicerBenz thanks for the reply bro 👍❤

[@jtsn667]

What injectors you using?

[@RicerBenz]

Still stock.🙈they are keeping up from what I’ve been told😅

[@21jsboy]

Bro need to to do a tune asap

[@RicerBenz]

Ayden on your car? Just looked at your videos👌👌👌 Are youHappy with smaller pulley ?😁

[@21jsboy]

@@RicerBenz yes I need to do my car my bro, all the way from Sydney Australia

[@RicerBenz]

Freaking awesome man!!!😁 Make more videos😁🤣I’d love to see your dyno results. I didn’t gain much power but at least I know it’s not running lean from the extra boost. Also I need to replace the pipe behind the air filter. Yours sounds soooo good(the wine) 👌😎

[@Esmeralda-alija]

Hp ???