Great to see your W211 achieve 200K+ miles! For ten years I've owned a black 2005 E350 AG, now with 69K miles. It's a joy to own. I love your attention to factory specs, doing it right... eg: the correct coolant mix using distilled water as diluent :-)
@genedipaolo513910 ай бұрын
Just did the job on my 06 CDI. Great video from parts, torque values, and routing of serpentine belt. Outstanding!
@Hristo19285 жыл бұрын
This was very helpful. Please make a video about the EGR valve cleaning or replacement of the E320 CDI
@RobertSmith-di5ll6 жыл бұрын
I'm a fan of your detail
@aleksandragendera82917 жыл бұрын
Couldn`t find anything about E320CDI waterpump change, and foud your video! Thanks a lot! You saved planty of my time :)
@rsrcisco867311 күн бұрын
HI, just asking , no need any silicone sealant for water pump? I have to change for my 220 cdi and skf pump have just one aluminium gasket (like yours)
@percyanderson34742 жыл бұрын
Very good
@PARDS24 жыл бұрын
DR---BEAUTIFUL EXACTING JOB AS USUAL FOR YOU. SUPERB DETAIL!!!!! DID YOU NOTICE THE TOP BOLT ON THE THERMOSTAT BEING LONGER THAN THE OTHER 2?? ALSO, NOTICED A STRIPE OF BLUE LOCTITE ON MOST OF THOSE BOLTS, DID YOU REDO THE TEMP LOCTITE?? DOES "WIS" RECOMMEND THAT? THX AGAIN!!
@TedMartin15 жыл бұрын
After filling up with antifreeze have you got to bleed the system? If yes how? thanks for a tremendous informative lesson.
@canekotevski6606 жыл бұрын
Car D. Ologist 7.7 litres Antifreeze + 7.7 litres distilled water? Whole system 15.4 litres fluid? Thank you for this great video
@farerse4 жыл бұрын
Good video , how are the hoses connected to the radiator? Looks like it twists and seals. I have not seen that connection type before.
@mb.warehouse_find42217 жыл бұрын
why didn't you tapped it before installing? just an observation...very detailed thumbs up
@jadesluv6 жыл бұрын
I bought a Borg Warner thermostat, neither of the two holes were tapped, the screws are not thread cutting screws, I wonder how may people don’t tap the holes and damage the housing. The bracket screws are the same length as the thermostat so I torqued those to slightly more 10Nm nearly as the thermostat @9Nm and its easier to tap with the thermostat unmounted.
@lepadatupetrica84875 жыл бұрын
What is the temperature on your thermostat? 92 or 87? Is duo heater valve can block the coolant and increase coolant pressure and lose coolant on expansion tank? Thank you
@pfoxhound5 жыл бұрын
Did you check coolant hoses for EGR?
@ruhsatigoek16322 жыл бұрын
Good video super 👍
@mohdnasirsalleh50567 жыл бұрын
good job Doc...me (Malaysia)
@BikerBloke6007 жыл бұрын
Great videos, will need to do this myself soon. How do you get the WIS System, do you have to purchase it?
@card.ologist45707 жыл бұрын
Yes. Usually can be found on ebay -- a few disks to load onto a computer. Really helps.
@BikerBloke6007 жыл бұрын
Must have a look as it would be invaluable. Thanks. Keep up the good work. 👍
@1995RangeRover7 жыл бұрын
Love your vids!!!
@card.ologist45707 жыл бұрын
Thanks!
@geojbig7 жыл бұрын
Subscribed and find your vlog so valuable, Thankyou! I have a 2005 cdi, where did you get the high mileage badge?
@nimakianipour88317 жыл бұрын
how do you burp the cooling system?
@farerse6 жыл бұрын
remove the coolant lid and run the Engine to operating temp
@hifibloke Жыл бұрын
Idler pulley 35Nm
@TheDomin8rr7 жыл бұрын
Very nicely done! I'm just about to reach 240k miles on my '05 W211 CDI & it is a Florida car too. If you're curious as to what might be in store maintenance-wise in next 40k miles, I have documented everything that I've had to replace over that time @ fuelly.com... My handle there is 'PSDCamperVan' Keep the DIY's coming, excellent!