Diagnosing and repairing a flooding problem with the Mercruiser Turn Key Start Carburetor
Пікірлер: 34
@carloschan1936Ай бұрын
Excelente bro
@servandocabrales22132 ай бұрын
What did you use to clean the module
@danny.tanker47442 жыл бұрын
What’s the part number?
@joeback8705Ай бұрын
What’s the part number on that enrichment valve I ordered one but wrong part
@IS-21713 күн бұрын
Hey there. nice video thanks for sharing. I have the same motor. what does it mean if the sucking/hissing noise doesn't go away? My boat starts fine. If I'm out on the water after running for a while and shut it off it doesn't turn back on first try though. usually second try. Usually I open the throttle 1/4 as well. Any ideas? OH also wanted to add to this. I can smell gas at cold start and get a little bit of smoke after idling and moving really slow. can't tell if its smoke or steam i think smoke. looks white.
@MackDK7712 күн бұрын
I have a 2007 4.3 TKS and same issue with the hard starts when it's warm. Already had it in and they said the TKS module was fine, has power, opens/closes.
@snejjens12 Жыл бұрын
Would your boat smoke a lot if it was the enrichment module.
@servandocabrales22132 ай бұрын
I have a 2005 Tahoe Q4 with a 4.3 seems to have this problem
@Rivreed196311 ай бұрын
When I bought my boat it had the old valve in the glove compartment, so I think it’s been replaced. The damn thing needs to be replaced again it’s warms up then won’t idle.
@keithdickinson60453 ай бұрын
Thanks for posting. It fixed my problem! Not a cheap part, though!
@yachtwork2 жыл бұрын
What a great video. Good info. Lots of background. Nice work. Thanks for posting. That is the exact issue we are working on.
@hunterm.1722 жыл бұрын
Wondering if you could help me I have a MerCruiser 470 3.7L and it runs amazing until the engine gets around 165 to 200°- acts like the engine is starving for fuel and I have to throttle it up Way high just to get it started back and it still won’t idle I’ve been chasing around to see if it’s a vapor lock issue and the only way that could be (after my new set up with fuel lines/check valves/return line) is the carburetor getting heat sink but I still don’t really feel like that’s the issue I still have the cam driven mechanical pump is there anything that you’d recommend me doing the boat runs amazing it’s just until that temp range. I was out on the water and had to force feed it fuel out of a bottle straight down the carb to limp it back to the dock… very frustrating because I’m so stumped… i’ve seen some people put a 12 V fuel pump in line to keep it forcing fuel into the carburetor-what do you think?
@mylolee82222 жыл бұрын
I have a 2004 mercury cruiser 4.3 thunderbolt. I have the same problem. Cold starts is good. But engine hot it died o. Idle. So is it the same part that bad? Please let me know thanks
@brianwalsh70805 ай бұрын
Great explanation. About to change that on my 5.0
@andyhollister46102 жыл бұрын
Damn mine's doing the same thing but I got the older model carb with the electric choke what do I do
@nutcracker85413 жыл бұрын
Can you add voltage ( if so what voltage ) to see if the module is working? Or can I set for voltage at the connector, if so what voltage should I be seeing?
@josephallen58567 ай бұрын
I've come to hate the TKS. I have had my carb rebuilt, and replaced this module. However my engine dies once the enrichment valve engages and closes off the enriched fuel/air. I troubleshot this motor for a whole summer and finally got it running good after replacing the spark plugs. Next summer, exact same problem again. Again new spark plugs, but no help.
@atxdude14 ай бұрын
Did you figure it out?
@josephallen58564 ай бұрын
@@atxdude1 not yet. Probably tinker on it in the next couple of weeks
@mikehillion3333 Жыл бұрын
Thanks so much for sharing
@brianwilson7950 Жыл бұрын
Thanks for the info!!
@jefferymeasles4193 Жыл бұрын
Great video! Mine is bogging out when I throw it into gear. Any suggestions?
@jeffmurphy99879 ай бұрын
Possibly idle is to low. Set idle around 700 rpm when put in gear at idle shouldn’t drop below 650.
@mylolee82222 жыл бұрын
Hi mark
@jrdecola2 жыл бұрын
Thanks for the video. My 2007 tahoe was doing the same thing.
@MarksBoatServices2 жыл бұрын
Glad I could help!
@romualdaskriksciunas36932 жыл бұрын
I've 3.0L. Equipped with fuel enrichment too. And I've same problem here too. It's starts fine, runs about 10 min or so. While its running, I can hear the whistle. My understanding, the whistle - its an extra air been sucked in to carburetor through that pin hole. ( when you remove the enrichment from the carburetor , there is a little pin hole on the side of the carburetor ) , so, that's where the extra air gets sucked in and gets mixed with the extra fuel ( extra fuel that gets through the enrichment valve spring ). Please correct me if I'm wrong. So, after 10 min, the engine warms up and that's where the enrichment valve kicks in. The enrichment valve starts shutting down, pushing the plastick valve towards to the brass tube, completely closing down that little spring inside the valve. Please correct me if I'm wrong. When the enrichment valve starts shutting down, the whistling slowly starts disappearing. And at the same time my engine rpm starts slowing down and the engine slowly stalls. I can start it again for 1 minute and then stalls again. And after that won't start until next morning or so. Can anyone identify my engine problem please. BTW, Have you tryd to dismantling the enrichment valve ? I did. And my understanding, it works like termostate valve , but oposite way. When I unscrewed the black plastic tubing ( where the two copper cables goes in ) the brass unit came out. I have dropped it into the hot boiling water and I could see the pin coming out of the brass unit. But I'm not sure is the pin coming whole way out? As you have mentioned on your video, your enrichment valve wasn't closing whole way down / closing not fully enough, leaving a little gap for the fuel to get in ( through the little spring ) to the carburetor and flooding it with fuel. Also, I have noticed ,where the two copper cables going in to the enrichment valve, you can adjust the distance between the little spring and brass tube by screwing it in or screwing it out. I have screwed in by 3 milimiters or so, but I have no time to test the engine eyt. It might be the case, but I had no time to test it out. Has anyone any ideas? I have spen few hundred euros , have changed fuel pump, water pump, hose, termostate and etc , before realise that all these parts were 100% working. Don't want to throw away another 300euros for new enrichment valve, unless someone comes with an answer to my problem, that the enrichment valve is definitely the problem and I need to replace it. Thanks in advance. Waiting for your replay.
@bubrunner0 Жыл бұрын
Im late to comment, but have you figured out what is going on, I have the exact same problem, but the part is so expensive I dont want to buy one just to try out
@alexeyskoromnov1608 Жыл бұрын
@@bubrunner0 hello, exactly the same, cold engine starts perfect, enrichment valve started to close down in 5 min, then after about 10 min when the engine was warm enough the engine was stopped itself it looks like was cut of ignition. I tried to start it again but could do with almost full gas, then it works few minutes and stopped again and I couldn't start it at all. I tried and tried but with out any chance. I checked that fuel normally pumped into carburator when I pumped by acelerator. I checked wires with ignition spark and there was ok spark. So It too strange that the engine didn't want to start. Please help if you know 100% solution.
@christianmalouin6522Ай бұрын
The year of this engine?
@nutcracker85412 жыл бұрын
Hello, My Enrichment Module is not get any voltage.. I applied 12v to the Module and it will engage. Do you know where the voltage is coming from? I have seen that it could be the oil pressure sensor but put a meter on the tip and no voltage there either. Should I be reading voltage at the tip of the OPS? My oil pressure gauge seems like its reading fine... so not sure... BTW.. its a 2005 5.0 TKS HELP!!
@MarksBoatServices2 жыл бұрын
Check the oil pressure switch for power. V8 has a sensor and a switch, i believe it gets power from the switch in your case. If not just start checking fuses.