Miele Novotronic W812 Change the bearings

[@matthewedgar59]

good video, after 17 years I changed the bushings, I needed a 2 arm gear puller to free the spider. Also when you disconnect wires from the heater element, there is a white plastic piece. above it with a rubber hose plugged into it. remove this hose. It's the water level sensor. This is a rewarding job, but a time consuming one. It also saves you a lot of money. I would change shock absorbers and put new brushes in the motor while you have it apart. Make some notes and take your time

[@ritarajczi6132]

Please help me! How much kg of clothes can it take? I have searched all over the internet, but nothing.....

[@AndreaNegri-gl9fh]

@@ritarajczi6132 5 kg / 47 litre volum

[@Martindyna]

After doing all that work, which I admire you for doing, I wonder how long e.g. the Programmer will last. This may be why Miele say it's uneconomic to change the bearings. P.S. I wonder how much a new programmer would cost. These days you can of course design your own PLC based programmer if you're that way inclined.

[@siemens130]

Thanks!:)A little over an hour.But I did not at once but in stages. I took it apart the machine and then waited one day until the arrival of the bearings.

[@thumbsdownbandit]

Took me 10 hours

[@TheAlfredcan]

I don’t think you checked the inner drum spider... worth doing - I think mine is making mine off axis and rubbing on door seal (and this is causing rumbling noise). Bearing I think is fine. Apparently the aluminium ones corrode...

[@mybluebelly]

Holy macaroni, you took out the whole thing. I have a Miele W 149 toploader. I hope i won`t have to take the drum out when replacing the bearings.

[@williamstilgoe61]

Well done but I could hardly see anything.

[@paulwharton1850]

Really interesting - Thank you. I hope the new bearings last as long as the original Miele one's.

[@devonslo]

Where is the inner drum spider ?

[@fredchen984]

I have a Miele 3035 washing machine. I pulled out the inner drum by accident, the drum was off axis and make a lot noise. What should I do? Please help me, thanks!

[@siemens130]

The motor bearings are not in bad shape.Were oiling.The commutator has been cleaned.The engine has been cleaned of excess coal dust.Only I did not show it!:)

[@kellianv5788]

Wow I'm impressed! Only that I was waiting for the moment you would remove the door seal I don't know why but.... And know I need to look further how to take it out.

[@rmariu]

Your motor needs servicing. Replace the bearings and using a commutator stone helps. A better bet would be to replace the motor bearings, lathe the commutator until it is round and use a seating stone to help bed the new brushes in. It can be difficult to remove the pulley from the motor.

[@DanielSmith-mk6jk]

Can you please help, I can't seem to knock the drum right through the bearings?

[@alexdemid02]

Уточните модель или модельный ряд Miele, с силуминовой крестовиной. С уважением!

[@MrLavadoro]

Hi!, very good video!!, In the past my grandma had one (the grandma who has the bosch), they are a very good washer, Thanks for uploading this vid!!

[@sandor4868]

Szervusz! Szuper a video, koszonom a segitseget, pont ezt kell csinalnom a Mutterom gepevel. Add meg, legy szives, a csapagyak es szimering adatait, koszonom!

[@siemens130]

Szia!fejből nem tudom de ha kiveszed úgyis meglátod.

[@jesper6107]

hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?

[@siemens130]

Yes,the music is pop corn.

[@maturaSigma]

Its like bauknechtboys style

[@fabriceverhamme9556]

good video, but too fast to follow

[@Миха-ю8г]

как называется музыка?

[@siemens130]

Pop corn

[@mielematic723]

Good! I do it now also with my W723 :-D

[@pwieringa2]

Good stuff, better than my bosch 2008 model with plastic water drum outside , a mega job complete demontage of all units. ?.........

[@siemens130]

Yes.

[@darkulo4]

Wow. That was a great job. Thanks for showing us :)

[@zahidshafi4925]

Good video to fast to follow

[@stuartbarrow666]

You took one hour then you must know what your doing then pal.

[@servistools5691]

😎

[@siemens130]

Thanks!:)

[@dejupp]

fucked up sounds

[@floparis1100]

it's verry good vid's!!!

[@marcoaigner9676]

Des Video is ve de Fisch do sixt nix wos a duat

[@norbertbluhm6430]

Wie Sie sehen, sehen/sahen Sie nichts...

[@jesper6107]

hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?