Installing a TURBO on our BUDGET 50cc Drift Kart!

[@itsmikelake]

We're doing a 125cc TURBO swap! kzbin.info/www/bejne/eJyrh5SIeap0ors

[@rileywhittle1512]

The thrust bearing inside the turbo requires oil pressure to keep the impeller shaft floating in a film of oil otherwise it contacts and wears

[@feelincrispy7053]

Depends if it’s ball bearing or bush

[@aeroflopper]

​@feelincrispy7053 both designs still need an oil feed

[@itsbrendoni3444]

weld a nipple on the cap and pressurize it, remove cap for oil change

[@BadHarmonics]

Journal bearing chra requires unimpeded flow, ball bearing NEEDS a restricted orifice ( on a car). This is almost certainly a journal bearing chra , and won't even spool correctly without proper flow / slight pressure inside the chra, and 270 thrust bearings( like this one probably): are even more dependent than a 360. Either way, the oil flow is also 1000% a necessity to not burn oil and coke up the bearing.... As all oil burns at turbo temps. The video guy is confusing the oil supply requirements as being similar to a roots blower. It's like building an engine without rings. You can do it, and it'll run. Maybe even for 30 whole minutes.

[@ACplanet]

will filling it up to the near top thread, then screwing the bolt in, pressurize it?

[@philliplock9249]

I agree the turbo placement looks awesome, but you'd probably find it more efficient bolting it to the intake. That'll give room for the expansion chamber, while offering instant response.

[@itsmikelake]

I definitely agree with this, but it looks so damn cool 😅. We’ll re engineer some of the setup on the next vid and see how it goes 👌🏻

[@Thumper68]

A small oil cooler etc used as an intercooler will help

[@cxbra]

The turbo needs the exhaust for scavenging, then the compressor goes into the intake. If he didnt strap it to the exhaust, it might spin but wont make positive boost.

[@Mrshotshell]

@@cxbra Pretty sure he meant to have the expansion chamber before the turbo

[@stuartwilson9064]

I used to get into 2 stroke rc cars, I would think a bigger expansion chamber would help. You could maybe loose the gasket under the cylinder to get a little more compression (use some goo instead and check the piston isn’t going to touch the top of the cylinder). Not sure how the clutch works in that thing, in the rc cars they were two half’s held by a spring. We would use a heavier spring so the clutch would engage at higher rpm’s. 🤷🏽‍♂️

[@itsmikelake]

Amazing suggestions! Yep the clutch works the same as you’ve explained and I can in fact get heavier springs!

[@wilsondriver654]

​@@itsmikelakemight need lower gearing?

[@Atris_965]

Hpi baja ..

[@itsmikelake]

I can't believe this actually WORKED?! 🤣Should we do a part 2 with boost gauge etc? We need to paint the frame too 🤔

[@shaneanning180sx]

Yes part 2 please love the exhaust lol

[@MaddyBoi_86]

Soo totally need to give it a bov ha ha. Love it ❤

[@armandtventer8855]

Yes so keen for part 2!!!!!

[@chickenwing071-6]

YEAH, I WISH I HAD ONE

[@theLyzhendricks]

Of course we need a part 2

[@jamesgrech8295]

Put nitrous on it

[@waelal7484]

Every engine needs a expansion chamber tuned to its timing and rev range an displacement you can do your search.

[@itsmikelake]

Thanks 😁🤙🏻

[@Toxic2T]

truth. Once he learns its gonna be a drug to him. Each pipe has a diff result.

[@minecraftblockychris8708]

its the other way around?

[@cxbra]

A turbo 212cc 4 stroke would be even more insane! And tap a inlet and drain like that go to the bottom of the block in the oil "sump". Since 2 strokes dont have an oil sump, you couldnt get any heat relief from the hot oil inside the turbo. With. 4 stroke you would even be able to add an oil cooler in theory (which would cool the MOTOR down from the high pressure intake AND the turbo). Im surprised it worked using the same fueling as it did with n/a. Wow VERY cool many!!

[@LokiMelb]

So good, I saw your thumbnail the other day, so Sunday morning got into the garage and finally welded my LCA to my 50cc drift quad. Still need supports and then chop the frame for the seat. But getting there. Love the tiny turbo!!

[@kanalagamer]

The homemade expansion chamber is not very good because the shape, curve, length and every other factor has to be considered for it to work. They are specially designed so that the exhaust gasses push any remaining fuel from the exhaust back into the cylinder. I suggest you get an expansion chamber of like a 50cc 2-stroke moped and use that. Expansion chambers can like triple the power output at high rpms.

[@Bullwinkle39]

100% this. Every mini moto I've built for more power, the engine mods did virtually nothing but put a Leo Vince TT chamber on and the engines instantly come alive

[@Toxic2T]

Indeed. 1/3 of the power comes from the pipe. The rest comes from compression, intake/carb and porting.

[@That1E_K1129]

Good job busting the myth of being able to turbo a 2 smoker. Me and my dad did it to a twin cylinder 440 jag smowmobile about 9yrs ago. It definitely works and definitely makes power! Awesome job man. New sub from me.

[@itsmikelake]

Thanks bro! Yep, I’m the type of guy that just gives it a crack regardless of what the internet says haha. Turbo snowmobile would be so good 🤣

[@That1E_K1129]

@@itsmikelake it was a for sure ripper man I wish I had video of it 🤣 thanks for replying my man! Keep killing i!

[@rocketdragon4855]

If you'd want to make a 2 stroke exhaust that actually works well, you'd have to use a 2 stroke exhaust "tool"/calculator to get the correct measurements for the exhaust.

[@itsmikelake]

I was looking at these online! We’ll upgrade the exhaust next vid 😁

[@rocketdragon4855]

@@itsmikelake cool! I'm looking forward to it👍

[@Ismaak5]

You need an external oil system or the turbo won't last. I give it a couple of days before it lets go. There needs to be oil pressure in the bearings in order for the shaft to not come in contact with them. They need to float in oil not just sit in stagnant oil.

[@itsmikelake]

Yeah that’s something I’m currently trying to sort out 🤔. I have a few ideas. I wanted to figure out if the 2 stroke would even accept boost first before sorting the oiling stuff 🤙🏻

[@needmoreboost6369]

That’s correct under normal operating circumstances! but for this motor being suspended in oil with will work,And for a lot longer than you think! it’s submerged in oil! It’s not the same as in normal operation on a larger motor running out of oil!

[@Ismaak5]

@@needmoreboost6369 apparently you are confused on how a journal bearing turbo works. Filling the cartridge with oil doesn't work. For starters the cartridge is not airtight there is a way for the oil to escape on both the compressor and the turbine housing. Secondary the oil needs to be pressurized or the bearings will come in contact with the turbine shaft. It is the same with any motor operating a turbo in fact in the case of a single cylinder engine it is even worse than a multicylinder engine due to pulsating waves of the exhaust pressure. Spinning the shaft at any speed will make it come in contact unless there is pressurized oil flowing through it for both lubrication and cooling. Especially with a small turbo that spools up quickly. The passages of the journal bearings are so small that without pressure essentially the spin of the shaft pushes the oil out of them.

[@Madaz]

@@itsmikelake maybe an aquarium pump with an external oil resevoir

[@rajgill7576]

​@itsmikelake lol I get the sort one before you sort the other but trust, you want oil going to that turbo asap. I've broken a new turbo before by trying to sort out boost before lube. Not making that mistake again haha

[@Weidner36]

Yes you can turbo 2 strokes.. I live in lake havasu city, az, USA and I've turbo charged so many 2 strikes even in the 125f degree weather and they love it. Remember to use a 2 cable throttle cable so it dosent run away from you

[@itsmikelake]

This is what I like to hear!

[@warmfreeze]

depends on the TYPE of 2 stroke your putting forced induction on.. but mostly your just blowing the fuel charge strait out of the exhaust..

[@chrishenniker5944]

You can’t add forced induction to a two stroke, it’ll blow right through. A four stroke, they’re made for it.

[@warmfreeze]

@@chrishenniker5944 again it depends on the TYPE of 2 stroke.. snowmobiles have an intake valve

[@einhase6924]

If you really want to increase the power, you need to port it. Something like a wieder exhaust port and a higher exhaust Timings. Then you need a different expansion chamber. In general the champer should be shorter, but it must be tuned for your setup. You can also bore out the carburator or get a bigger one.

[@Toxic2T]

This, no need for turbo. Just porting, better reeds, bigger carb with proper intake tube and a custom pipe will do the trick.

[@LloydWhitham]

Another killer vid mikey!! Cheers mate, looked super fun!

[@itsmikelake]

Thank you bro! Fun little rig 😁

[@robertgillin]

you can definitely turbo a 2 stroke if your carb is a float bowl type you need to feed boost into the carb vent if its a diaphragm type its not necessary

[@itsmikelake]

This is the EXACT type of info I’m looking for. Thank you 😁

[@barrymccockner6450]

When a momma turbo and a daddy turbo fall in love , you get a baby turbo !😊

[@effigy42]

I worked on tiny 2 strokes for years just out of my garage and the biggest and best horsepower upgrades were aluminium motors with bigger carbis top speed 80km an hour with my worked 50cc iron and 95km with the 73cc iron but over 110kmph top speed with aluminium lighter has such a significant effect when so small

[@itsmikelake]

That’s so fast 😅. I’ll do my best to get as higher top speed out of this one 😁

[@effigy42]

@@itsmikelake good thing would be getting more traction for faster drifting then wouldn’t it

[@Teagan762]

Expansion chambers on 2 strokes can't just be guessed at. There as important as tuning a cars ECU. Length of pipe between the carb and chamber, Chamber to turbo and exit. Cool little build. I've built many.

[@itsmikelake]

I’ve certainly learnt this with this build 😅. Cheers 👊🏻

[@diyathomevn]

a new car. turbocharged motorcycles. I agree that the turbo placement looks great, but you'll probably find it more effective to mount it to the intake. The turbo needs oil pressure to keep the impeller shaft floating in the oil film, otherwise it will become exposed and worn.

[@MicahBell_1860]

Happy trails, Cowpoke

[@itsmikelake]

🤣🤣

[@paolocane8875]

😂 that's the basic of 2 stroke engine! An expansion! But have to be specific misure!😅 That's not an expansion, that's a swollen pipe!😂 It looks amazing anyway!😎 Good luck!

[@itsmikelake]

I’m learning as I go 🤣 but thanks for the advice!

[@Just-A-Guy-Learning]

Oil cooler, diesel fuel pump, very light weight oil, and oil catch can. Also a 12v source to power the fuel pump. Fill the catch can with oil. Bottom drain of catch can goes to fuel pump. Fuel pump, pumps the oil through the turbo. Drain of turbo runs to oil cooler inlet. Outlet of oil cooler goes to top port of catch can. Since you are adding a 12v source to power the fuel pump you can also add a small 12v oil cooler fan to the oil cooler.

[@Scxjunkie]

The little waste gate sound is much needed

[@f.450d.c6]

Hey brother, the only thing I would say is it’s a beautiful thing I would do is one I’ll get a different engine and make it a little bit more powerful I understand you like tiny motors. It’s really efficient and everything else but you’re doing the turbo outside, throw much bigger engine on it For stroke 110 engine so you can get rid of toppers and probably make something a lot better but you do have to worry about the field mixture and everything else then but if you need some help with that. Just talk to me.

[@steelearmstrong9616]

That turbo on there looks awesome

[@itsmikelake]

Cheers!

[@meandthecat4025]

I randomly got hyped for this video. I'm so curious!

[@mopadrider6012]

This takes me back to the time i shaw a turbo gy6 scooter racing and winning against faster cars like whaaaat

[@chrisdocking9255]

Mike lake you savage! Look at how many like this video has!!! Bro I’ve been a sub since the bmw swapped, supercharged Corolla! You have grown my boy and my man I am so proud of you! Don’t stop baby don’t stop! Love from Nz

[@Turbowagon]

Very cool looking forward to future progress with this

[@itsmikelake]

Cheers! Part 2 drops tomorrow 👊🏻

[@thatjdmkid8170]

I’m great at tuning those engines! I want to build one now

[@Catalin-Nicolaevici]

It works iv seen it done before. Only issue you have is the oil "you gotta make a oil tank" and I highly recommend some type of intercooler cause 2 cycle builds heat like crazy and your adding a turbo. It's not gonna run good. But if you have a way to cool it down it works grate

[@777Mizpah]

May God Bless And Be With You All Throughout Your Journey And All Throughout All Of Your Time Building Cars 💙

[@captcade2913]

You should make coloured smoke on the wheels, that would be sick

[@Fk8td]

Larger expansion chamber on the exhaust should help it rev a bit more because total exhaust volume will be larger allowing more total exhaust out but at sacrifice of lower rpm and mid range power

[@TURBOTRISTO]

SOUNDS GREAT

[@itsmikelake]

Knew you'd love this one Tristan! Haha

[@grimairbrush]

hey mike, the turbo flutter on the 2stroke was pretty awesome lol

[@itsmikelake]

Thanks bro. So cool hey 🤣

[@joshydoy]

you should get the 19mm carb with the uprated intake for this so the carb isnt a huge restriction

[@robivlahov]

build an airbox that houses the whole carb, and boost into the airbox, you are having trouble with the pressure differance as its not a blow trough carb. pull the piston out cut it up to remove the piston port and make it reed induction, so that the turbo has more time to fill up the cranckase and cylinder.

[@jake3085]

Cheers for dropping this on my birthday 👌 few ideas, put a dose pipe on the intake of the turbo, fiddle around with the length and maybe we can hear some vl turbo dose noises coming outa this thing Also, see of you can hook up a wideband to this thing, its probably leaning out as I imagine the boost will push the fuel out of the carb, maybe add a vacuum line from the charge pipe to the fuel tank so that there is no pressure differential in the carb Make a new dump pipe where it separates the wastegate opening then have a muffler and a screamer pipe Im half tempted to go buy a little pocket rocket and try this stuff now 😂

[@itsmikelake]

Happy birthday my bro! Haha crazy that everything you’ve suggested is exactly what I have planned 🤣🤙🏻

[@jake3085]

@@itsmikelake cheers bro! Great minds think alike hahaha

[@DennisFerri1]

Dude, what size turbine did you use and what model is it?😊

[@_CryptoNoob_]

Making a small oil tank would have way too much work eh? Lol

[@thatjdmkid8170]

I’m bout to pick up the same quad just because of this

[@hopdjandy]

Love the sound of it dumping

[@itsmikelake]

Same 😍

[@mechanicfromeurope]

It sounded like it was edited in

[@gsestream]

tesla disc turbine pump is the simplest diy turbo pump. very easy to diy. from sheet metal, spacers and bolts/rivets. yep stainless high temp. also very rigid structure. planar plates with supports. looks like a large flat multi-story building. nothing complicated in the structure.

[@anubisblack521]

you should have a carbon seal installed in the turbocharger for a draw through carburetor system ideally!

[@itsmikelake]

This would certainly be the ideal setup!

[@paydroku]

The world's cutest turbo 😂its a key chain bro

[@itsmikelake]

Haha exactly right 🤣

[@bryannakvinda8411]

Why not get a pump and tank for oiling the turbo not a hard system to build fyi best to put carb behind turbo and using starter fluid to bump it off on first start

[@discipleoftheword1785]

100% passion projects are so much more interesting to watch. Kind of feels like I’m a part of it.

[@itsmikelake]

Absolutely agree! Thanks for watching 😁. Part 2 coming next week 👊🏻

[@Justin-DA-Monkey]

u should get one of those scooping filers for the turbo and maybe make a better expansion exhaust and intake or probably upgrade the engine like a big bore kit or sum for the turbo to work better cuz i lowkey wanna see the limits of that engine

[@Justin-DA-Monkey]

and if u need a pump for the turbo just make a mechanical pump thats connected to the engine so it would be like a supercharger but a pump and make sure to gear it down too cuz its just a lil pump

[@itsmikelake]

I agree with you bro, I’d like to see the limits of this motor also! We’ll be making upgrades, don’t you worry 😁

[@rishujatav5585]

OP modification bro 👍💪🥶

[@itsmikelake]

Thanks!

[@relicgamer2137]

Love to see this with proper rear tires on it. All it seems to be doing is spinning on those plastic wheels doesn't help see how well it preforms

[@Custom_crusader]

rig the pipes get a second mini turbo and make a head light kinda thing it would look sick

[@itsmikelake]

2 turbos?! Haha

[@EdsEds-f6k]

Well done lad

[@frankz1125]

I build chainsaws and .020" squish is usually good to boost compression and port work. Nitros works as well. Cheers

[@RollinMyOwn]

You should talk with 2strokestuffing....he is nothing short of genius about 2 stroke motos...

[@havegrinderwilltravel5]

Haha that's awesome love flutter ❤ good work mate that's what life about having fun just giving it a go 😎✌️

[@itsmikelake]

Thank you my friend haha. Fun was certainly had!

[@InternetGangster420]

STUUTUUSTUUSTUU!🔥

[@mick00000000002]

Could you put a oil system of the crank. Tank radiator and pump of the shaft. To cool down the turbo? More guys. Please. Thank you. Do the Max. Think out of the box guys. ❤

[@Clippy_1]

You can probably make even more power if you use a real two stroke exhaust pipe from a moped. If you want to make it faster and I would recommend to engine swap it with a Yamaha yz 80 or Honda cr 80 engine and make a shifter drift kart.🤔 Very cool project!

[@themartian1148]

i made a small turbo for a rc car and they run like a 2stroke and it worked i was supprised because alot people say you cant turbo them but it seem that you can

[@fabio77809]

Hi Mike, thanks for posting this video

[@itsmikelake]

You are very welcome

[@fabio77809]

@@itsmikelake A thousand thanks

[@speedhack.]

look into taking an expansion chamber off another quality brand 50cc-80cc bike engine to fabricate the manifold from. Not sure if anyone has said it yet in your comments but its good to add an air capacitor to help hold the boost in the charge pipe, about 200cc-250cc volume for your engine. Also blow through setups work well, just focus on getting it running well off boost first, and add a pitot tube with a straight section somewhere in it, and plumb it into the vent for the bowl. And last its common add a boost nipple somewhere to pressurize the gas tank when boosting. I dont think the turbo will last too long if everything else works right since the oil u put in there will never get a chance to cool down without circulation(the oil helps cool the turbo too), i would get a cheap fuel pump and make a small oil drain tank to scavenge oil from and drain to, just dont test it too hard before you get to doing this lol

[@itsmikelake]

You absolute legend! It’s so cool all the advice coming in for this build. Thank you 😁

[@speedhack.]

@@itsmikelake you're welcome. Lots of info if you look into turbo snowmobiles

[@olivermain5078]

Cool dude this go kart rocks🤘

[@scottybutterworth666]

Thats wicked you've inspired me!

[@itsmikelake]

Cheers Scotty. Bloody good fun!

[@Donvito-vk8vq]

He did to me to I’m looking for one to build up now

[@SuperkoolGuy21]

You should take the covers off the back tires and record a top speed run

[@mattdaniels2798]

If you think that's sketchy try doing the down hill drift trike on Okemo mountain! VT💪🏻

[@itsmikelake]

Haha yep, that's sketchy asf!

[@SkyfighterZX]

Next video: "We slap a turbo on a ROCKET SHIP" 😂😂 Also i absolutly love that tiny air filter, adorable

[@someweeb3650]

I wanna see 2 of these on a little 4 cylinder

[@icanseeyouallfromuphere]

Next you need to manufacture for sales 😂

[@itsmikelake]

👀 imagine haha

[@icanseeyouallfromuphere]

@@itsmikelake class bro ! ✌🏻

[@persvang90]

12V oilpump with a tiny oil cooler should work great

[@AnotherMick]

Cheers Mike ,, I reckon throw the other carby on the front of the turbo, , twin carb turbo drift cart🏎💨💨💨

[@chug_n_toke8849]

That's so awesome!!

[@itsmikelake]

Thanks!

[@discipleoftheword1785]

I want to see the next episode on this.

[@itsmikelake]

Should drop next week 😁

[@ericmuhlbeier8023]

They do turbo 2 strokes.. for snowmobiles.. I suggest u build an oil system for iT with a pump or the turbo won't last

[@itsmikelake]

We’ll keep upgrading it as we go 😁

[@AJRestoration]

Making boost noises, but not boosting haha.

[@lincolnking9039]

Hey Mike u will have to change the needle position too to get some more fuel in will run better too since u turboed a 4 wheeler

[@JoshPhoenix11]

Can you use reed valves on the intake with a turbo? Also you might want to run it slightly on the rich side so it keeps the engine cooler

[@doridex]

Lol this is so much like my budget drift kart! Same base quad too lol. Ive just swapped a gx200 clone motor. 100$ for 6,5hp

[@KiwiPowerNZ]

I can’t see any other comments mentioning this and I could be wrong but I don’t think I am. Shouldn’t the fuel bowl be at the same pressure as the boost pressure? And the fuel pressure needs to increase according to the boost pressure so that the fuel bowl can fill. Otherwise the engine will lean out because the boost pressure is stopping fuel from entering the fuel bowl or if the fuel bowl isn’t boost referenced then the fuel won’t flow out of the jet as it should because there’s a lower pressure in the bowl than in the carb.

[@itsmikelake]

You’re 100% correct! I didn’t show it in the video but I have a boost line going to the fuel tank from the turbo to pressurise the tank which apparently is enough to keep the carb filled with fuel 🤔.

[@paco_rider]

A turbo is not ideal for 2 stroke, but back in the 30's 2 stroke in competition were supercharged, till they were forbidden and then the exhaust resonator came into play

[@markkmchugh]

Nice work. Your not a nob either which is great :) New subscriber.

[@NFSgremlin]

Epic mate 🤙

[@itsmikelake]

Thank you bro 😀

[@CamdenIglehart]

might wanna add an airfilter to the front of your turbo so you dont dust your engine!

[@briankennedy6693]

The Boostedboys have a turbo “turbo shopping go-kart” a shopping cart on a go kart with a atv engine and that same turbo, theirs is a four stroke five speed and has a much bigger expansion tank, maybe watch a few of their videos?

[@itsmikelake]

This is exactly what I was looking for! I'll check them out now. Thank you!

[@aaronjnrnichols4642]

lets go mate u told me it would be here today thanks for being honest. great Vid

[@itsmikelake]

Thank you bro! Doing my best to pump out quality content haha. Cheers

[@aaronjnrnichols4642]

You should do a meet and great next weekend while im down there.@@itsmikelake

[@Eric_Henderson]

just put 2 of those 49cc motors on it, side by side with the single turbo, first of all its getting too much air for one little motor, second have the carb about 3inches away from crank case, and third have about 1 foot expansion chamber on both with a low compression head. I've built tons of stuff with these 2 strokes, more power means more motors lol

[@itsmikelake]

TWO MOTORS! That’s kind of a cool idea 🤔. I’m really keen to get it ripping with the single motor first. It has potential!

[@seanluna5956]

ive wanted to throw a turbo on my 2 stroke jet ski this gives me hope it might work

[@Altie8]

thats insane

[@jmrides777]

Great job bud...sheesh I had just as much fun watching this vid as you did building it. Where did you get the mini turbo from? I wanna put one on my kit bike.

[@itsmikelake]

Thanks! So glad you enjoyed it. Link is in the description for the turbo 😁

[@OfficialScrapMetal]

Drive it across the country

[@itsmikelake]

I think I’d get arrested 🤣

[@paperchik5901]

You need a Normal resonator you can use from 50cc scoter or mini 2stroke dirt bike Expansion chamber has 60% power from all engine an if it works not on correct rpm engine can’t reach high speed Second you need a Flap valve this thing prevents emissions of gas from combustion chamber actually makes the same thing as a resonator But on intake

[@itsmikelake]

Thanks for the advice! I'm researching 2 strokes at the moment & we will refine the setup in the next video 😁

[@Mufoom]

I know you probably won't see this, but you know what you have to do... twin turbos.

[@itsmikelake]

I have seen this! Haha. Maybe with a bigger motor? 👀

[@Mufoom]

@@itsmikelake An Inline 4-cyl? Maybe a bigger frame to accommodate it? 👀

[@Mufoom]

@@itsmikelake VTEC😮

[@Mufoom]

@@itsmikelake and then... supercharge, for all the fun noises in one!

[@Levi-eh7zq]

@@Mufoomcan’t vtec a 2 stroke

[@IAM2CAN]

did you play around with the ignitiontiming and colder spark plugs?

[@glock19cgen5]

you earned a sub from me dude I need a turbo go kart to get around on

[@itsmikelake]

Appreciate that homie! I think everyone needs one of these bad boys 🤣

[@domcxz8643]

THIS IS SO COOOOOL :)

[@itsmikelake]

Thanks!

[@SM-cg6kv]

Not on topic but I love the z!♥️

[@itsmikelake]

Thank you! I’ll be dropping new vids on the z real soon 😁

[@blizteredthumbs7911]

Not a turbo drift kart, it's a tirbo drift kart. 🤘

[@bosscalam4463]

i need to buy a mini turbo for my kart too