No video

Millets Primary Processing Unit, Layout & Design

  Рет қаралды 66,009

Tapas Chandra Roy

Tapas Chandra Roy

Күн бұрын

#TCRconnectingAgriculture #MilletProcessing #LayoutDesign
MILLET STORE:
www.amazon.in/...
www.tcrconnect... , My website promoting Millets, Millets Recipes, Millets Processing, Millets Farming Technologies, Millets Startups, Millet News, Millets Nutrition, Millet Foods, Organic Millets, Millet Business, Millet's happenings in India and World.
MILLETS PRIMARY PROCESSING UNIT:
1.GRADER CUM ASPIRATOR
Primary cleaning is done using a grader cum aspirator with support of different sieve sizes. Grader separates good quality grain from sticks, big stones, sand, grass etc . Here the material with different shapes and sizes gets separated. Selection of the correct sieve type and size is crucial in this process.
Proper care should be taken to prevent material from clogging.
Machine operator should use a brush to make sure the material doesn't clog. The good quality grains are sent for secondary cleaning for removing stones and mud balls. For small millet processing we normally use a triple deck grader with three sieves.
The top sieve will separate long sticks, big stones, grass etc which are bigger in size than the grain, the middle sieve will separate the good grain and the bottom sieve will separate coarse and fine sand.
The aspirator attached to the grader will have a small fan which will send the fine dust and sand particles to the rear end.
2.DESTONER CUM ASPIRATOR
The material coming from the grader is sent to a destoner for removing small stones and mud balls which are identical in size.
Destoner is a gravity separator which separates material based on the weight of the material. The cleaned grain from the destoner is sent for dehulling / dehusking.
A destoner has two sieves under the hopper which grades the material coming from the hopper. The graded material falls on the destoner bed where the lighter material moves towards the front end and the heavier material moves towards the rear end.
The aspirator attached to the Destoner will remove the fine dust and sand particles.
The air adjustment slot has to be adjusted carefully depending upon the material.
If there is no flow backward, we have to open the slot and adjust to flow the stones backward.
Destoner is suitable for removing stones and impurities from various Millets like Little Millet, Kodo Millet, Barnyard Millet, Proso Millet, Finger Millet, Foxtail Millet, etc.
Here one thing to add, it is better to have a Variable Frequency Drive.
It is used in electro-mechanical drive systems to control AC motor speed and torque by varying motor input frequency and voltage.
.
It will lessen mechanical and electrical stress, reducing maintenance and repair costs, and extending the life of the motor and the driven equipment.
3.DEHULLER CUM ASPIRATOR
The raw material after going through a rigorous process of cleaning in the Grader and Destoner is sent for husk removal to the dehuller.
(a) Centrifugal dehullers- A centrifugal dehuller has an impeller which is responsible for the husk removal. The material is sent to the hopper which then enters the impeller, where it gets thrown with a great centrifugal force onto the impeller casing. Due to the heavy impact the husk gets separated from the grain and is sent to the aspirator where the lighter husk is collected at the back and the grain is collected at the front.
There are two types of MILLET DEHULLER -Single Stage
This machine is most suitable for de-hulling small millets like kodo, proso and bardyard millets.
MILLET DEHULLER - Double Stage
This millet dehuller has two chambers for removing skin on millets like little and foxtail millet.
4. Pulviriser: It is a double stage pulveriser in which the grains, spices, rice, wheat etc could be grinded to a fine powder. Double chamber is provided in which the grinding process takes place. In the first chamber initial crushing process takes place and in the next chamber grains are made into a fine powder.
Millets (Little, Kodo, Foxtail, Proso, Barnyard, Finger, Pearl Millet & Sorghum)
1PROCESSING UNIT DESIGN & LAYOUT
To establish a millet processing unit you need atleast 25*25ft space with proper flooring and atleast half feet concrete laid under the flooring where the machines will be installed. The height of the walls should atleast be 10ft tall with exhaust fans in all the four corners.
All machines have to be installed using foundation bolts to arrest vibrations and also balanced properly. Machine installation is critical because it would directly affect the life of the machine and also it’s performance.

Пікірлер: 128
@networkmarketingbusinesssc6563
@networkmarketingbusinesssc6563 24 күн бұрын
👏👏👏👏👏👏👏👌👌
@urbangreenlife6350
@urbangreenlife6350 2 жыл бұрын
great information
@milletadvisor
@milletadvisor 2 жыл бұрын
Thank you so much for your nice compliment.
@aao-dasamantpur190
@aao-dasamantpur190 5 жыл бұрын
Good Video.Very informative.
@marthalachandraobulareddy8382
@marthalachandraobulareddy8382 5 жыл бұрын
Please contact no or address my no 9963291865
@chaturthela4191
@chaturthela4191 5 жыл бұрын
Millets food is best
@barunsagar3661
@barunsagar3661 5 жыл бұрын
Jhakash sanga
@SureshKumar-xs7nf
@SureshKumar-xs7nf 5 жыл бұрын
Nice work
@meramvlogs4260
@meramvlogs4260 2 жыл бұрын
Nice one
@milletadvisor
@milletadvisor 2 жыл бұрын
Thank you.
@srisuryamasalas5723
@srisuryamasalas5723 3 жыл бұрын
👍
@9908381827
@9908381827 4 жыл бұрын
In rural areas sir best quality
@ronaknikam9223
@ronaknikam9223 3 жыл бұрын
Great machine sir .....!!! I am Ronak from FY Mitaoe,Pune, Maharashtra I would be great if we have interaction about this machice (For educational purpose). If yes, then via which platform you would like to interact.
@karunakararaobotcha
@karunakararaobotcha 2 жыл бұрын
Hi, Nice video. What is the cost of the machinery?
@bijukply
@bijukply 3 жыл бұрын
Sir..nice and informative vedio..do u have any vedio or information about millet value added product line..like rava maker..roaster..blender etc..pls share ur number or contact I wish to learn more about value added line..thanks
@srinadh6
@srinadh6 Жыл бұрын
send me details of project and machinery costs
@milletadvisor
@milletadvisor Жыл бұрын
Hi, written a blog on Millet processing unit and named few manufacturers. You can directly contact them and get your quotation as per your budget. Please go through this article, it will help you in understanding the millet processing in a better way. tcrconnectingagriculture.com/2020/10/millet-processing-machine/
@hydtechietalks3607
@hydtechietalks3607 3 жыл бұрын
TOO COSTLY.. ANY MACHINES FOR SMALL SCALE FARMER SOCITIES..... ?
@venkatanarsimhareddy1402
@venkatanarsimhareddy1402 4 жыл бұрын
Hi sir nice video. I want full details sir.where this unit sir?
@milletadvisor
@milletadvisor 4 жыл бұрын
Thank u so much.This unit is at Indian Institute of Millet Research,Hyderabad.
@venkatanarsimhareddy1402
@venkatanarsimhareddy1402 4 жыл бұрын
@@milletadvisor Hyderabad lo addras sir?
@milletadvisor
@milletadvisor 4 жыл бұрын
Himayat Sagar Road, Rajendra Nagar, Near Andhra Bank, Hyderabad, Telangana 500030
@venkatanarsimhareddy1402
@venkatanarsimhareddy1402 4 жыл бұрын
@@milletadvisor thanks sir
@shishirsur3754
@shishirsur3754 3 жыл бұрын
Can you please guide us with cost of line up till packing
@bashuswaraj85
@bashuswaraj85 5 жыл бұрын
Please provide the cost for complete installation
@milletadvisor
@milletadvisor 5 жыл бұрын
It will cost about 5-6 lakhs for machinaries and construction of buildings about 4 lakhs(this may vary upon your choice).
@shobharampatel686
@shobharampatel686 Жыл бұрын
Please l want to visit to this workshop. Tell me adress.
@shivanidurgamwar7490
@shivanidurgamwar7490 Жыл бұрын
Hello where can we find this machines...?
@shobharampatel686
@shobharampatel686 Жыл бұрын
Please give me adress of some units and machine showrooms
@infodileep
@infodileep 3 жыл бұрын
Do you have ragi skin removing machine?
@pradeeprajchekuri
@pradeeprajchekuri 5 жыл бұрын
Please Let Me Know Where this Processing Unit is Installed?
@milletadvisor
@milletadvisor 5 жыл бұрын
Its in IIMR, Hyderabad & ARS,Vizianagram.
@pradeeprajchekuri
@pradeeprajchekuri 5 жыл бұрын
Thank You For Your Prompt Reply
@rk6135
@rk6135 5 жыл бұрын
Sir, i meet at vijayanagaram pls send address and phone no
@mrskusumnegi6600
@mrskusumnegi6600 5 жыл бұрын
how can i buy this mechine and other details
@milletadvisor
@milletadvisor 5 жыл бұрын
U can send your mail id..will send u the details.
@sivareddy175
@sivareddy175 4 жыл бұрын
lsiva051@rediffmail.com
@sreeseenu1582
@sreeseenu1582 4 жыл бұрын
@TCR Connecting Agriculture please send details to sreeseenu.70@gmail.com
@svranga1
@svranga1 4 жыл бұрын
@@milletadvisor sir, I would request u to send complete details. yours.reddysvr@gmail.com
@raghusai99
@raghusai99 4 жыл бұрын
Perfura Technologies (India) Private Limited #7, Maruthamalai Gounder Lay Out, Ramakrishnapuram, Ganapathy, Gopalakrishnapuram, Ganapathypudur, Coimbatore, Tamil Nadu 641006 098948 50009 maps.google.com/?cid=17424103355548501897
@srmv7457
@srmv7457 4 жыл бұрын
How much Minimum investment required for start processing unit
@milletadvisor
@milletadvisor 4 жыл бұрын
It depend on the capacity of machines and which brand you are looking for. Will send you the details. Pls send your email ID.
@srmv7457
@srmv7457 4 жыл бұрын
@@milletadvisor srinivasan.mv2011@gmail.com
@hemanthneo
@hemanthneo 4 жыл бұрын
Sir please send me details of the project..I m very much interested..My email id- Hemanth.neo@gmail.com
@saurabhporwal9529
@saurabhporwal9529 4 жыл бұрын
@@milletadvisor I am also interested in processing unit...plz share detailed information on porwalsaurabh13@rediffmail.com... thank you very much for such a informative video
@kaladharankesevan8901
@kaladharankesevan8901 2 жыл бұрын
Sir, I am planning to start a unit in Central kerala. Please provide me with the details
@9908381827
@9908381827 4 жыл бұрын
Mini rice machine processing unit
@azhakesanpillai2516
@azhakesanpillai2516 4 жыл бұрын
Any ideas on millet faking machine ?
@milletadvisor
@milletadvisor 4 жыл бұрын
U can have the technology from CFTRI, Mysore
@user-jd8ud4lf1r
@user-jd8ud4lf1r 3 ай бұрын
Sir,I wanna to install the processing unit in odisha.please tell about the procedure
@milletadvisor
@milletadvisor 3 ай бұрын
You can write a email to me about the details of your project. My email ID: tapas@milletadvisor.com
@ranjitbhaipatel8156
@ranjitbhaipatel8156 7 ай бұрын
What is price
@bpcgunpur9123
@bpcgunpur9123 3 жыл бұрын
can u inform us about its cost
@qma5104
@qma5104 Жыл бұрын
sir, is this machine can (dehulling) process oats.
@milletadvisor
@milletadvisor 3 ай бұрын
No, it is only for millets processing
@lokeshgupta7236
@lokeshgupta7236 4 жыл бұрын
Good job. Sir from where we can get all millets in wholesale. Please help
@ganeshgupta103
@ganeshgupta103 4 жыл бұрын
I can provide Ragi in huge amount 7979912559
@murlisahu6401
@murlisahu6401 Жыл бұрын
Machine kahan se khariden
@oegstv5899
@oegstv5899 4 жыл бұрын
Why nobody invents millet husk removing machine?
@shobharampatel686
@shobharampatel686 Жыл бұрын
It is too old. Please update it.
@v.chandravanshisonychirag7880
@v.chandravanshisonychirag7880 Ай бұрын
Could you share the Machine supplier's contact details
@MADAVAREDDY786
@MADAVAREDDY786 4 жыл бұрын
How much total amount in project
@Lakshmikumar08
@Lakshmikumar08 4 жыл бұрын
Sir, do you provide installation in chittoor district Andhrapradesh
@raghusai99
@raghusai99 4 жыл бұрын
Yes
@aveebittoo
@aveebittoo 3 жыл бұрын
Sir how to contact with you?
@milletadvisor
@milletadvisor 3 жыл бұрын
Please mail me at tapas3773@gmail.com. I will call you.
@sainaveenmorampudi7133
@sainaveenmorampudi7133 5 жыл бұрын
What is the capacity of that machines
@milletadvisor
@milletadvisor 5 жыл бұрын
pls provide your email id...i will send s details.
@sainaveenmorampudi7133
@sainaveenmorampudi7133 5 жыл бұрын
morampudi.sainaveen0001@gmail.com
@krishnamohanetagoni8945
@krishnamohanetagoni8945 4 жыл бұрын
Dear sir, Kindly send details to mohanka835@gmail.com
@premsaklecha9792
@premsaklecha9792 3 жыл бұрын
premcoolguy77@gmail.com...send me quotation Nd capacity
@mahfooz786withu
@mahfooz786withu 3 жыл бұрын
Kindly give information of plant mahfooz786withu@gmail.com
@chinnimanikanta7199
@chinnimanikanta7199 5 жыл бұрын
How much cost total project
@milletadvisor
@milletadvisor 5 жыл бұрын
It will cost about 5-6 lakhs for machinaries & construction of building about 4 lakhs.
@arvindkesharwani7588
@arvindkesharwani7588 5 жыл бұрын
Nirmata ka phone nu
@sureshmalsurana5341
@sureshmalsurana5341 3 жыл бұрын
Sir holsale millet purchaser give me name
@pandey5158
@pandey5158 Жыл бұрын
मुझे एक यूनिट लेना है कहां मिलेगा
@pandey5158
@pandey5158 Жыл бұрын
कांटेक्ट नंबर
@ShankarSingh-bz3ey
@ShankarSingh-bz3ey Жыл бұрын
Contact detail
@bhumikakandimalla238
@bhumikakandimalla238 3 жыл бұрын
Pressing nothing curret
@moyinolaoluwa4038
@moyinolaoluwa4038 2 жыл бұрын
Please contact me, I'm interested in your machine
@shivprakashbissu8180
@shivprakashbissu8180 10 ай бұрын
What's up namber sending
@manjithbunny6919
@manjithbunny6919 3 жыл бұрын
Not perfect hullar I.venubabu.kurnool
@AkashGupta-ig2tc
@AkashGupta-ig2tc 3 жыл бұрын
number send,kijiye
@milletadvisor
@milletadvisor 3 жыл бұрын
Please mail me at tapas3773@gmail.com. Will call you.
Son ❤️ #shorts by Leisi Show
00:41
Leisi Show
Рет қаралды 10 МЛН
Little brothers couldn't stay calm when they noticed a bin lorry #shorts
00:32
Fabiosa Best Lifehacks
Рет қаралды 18 МЛН
Magnetic Destoner | Excel Magnetics
2:37
Excel Magnetics
Рет қаралды 9 М.
Blueberries MEGA FACTORY: Processing Thousands of Blueberries with AI
11:53
The Smart Farm
Рет қаралды 1,1 МЛН
Son ❤️ #shorts by Leisi Show
00:41
Leisi Show
Рет қаралды 10 МЛН