Milling VW 02M AWD to FWD gearbox plate on DIY PrintNC - Start to finish

  Рет қаралды 18,225

Beaned

Beaned

Күн бұрын

Пікірлер: 26
@conradocarro4103
@conradocarro4103 9 ай бұрын
Just wanted to drop a line to say thanks for the video on machining parameters. Super helpful stuff!
@thomasj8681
@thomasj8681 9 ай бұрын
Thank you for sharing your work and a big thank you for adding speeds & feeds.
@TMonteiro.
@TMonteiro. 9 ай бұрын
Hey again! Big improvement with the feeds and speeds mate! Keep up the good work.
@keegansimpson340
@keegansimpson340 9 ай бұрын
running a SFM of 1374 is nuts!
@TheWrate
@TheWrate 2 ай бұрын
Darn impressive. Have yet to try aluminum on my PrintNC
@boessi
@boessi 9 ай бұрын
Sehr schön! Dafür gibt es ein Like!
@lefavour1
@lefavour1 9 ай бұрын
First things first, your parts look absolutely amazing! I am, however, a bit curious of your machine setup. Such as servos/steppers, drivers, and controller? I am also, so curious as to how you are holding the part? Is it just some double sided tape?! If so, what tape is that? Keep up the great work! -Caleb L.
@Beeeaned
@Beeeaned 9 ай бұрын
Cheers! It’s a pretty basic PrintNC build, just Nema23’s, StepperOnline DM542T drivers, PicoBob controller from Expatria (RP2040 chip for step gen, runs grblhal, utilises a Mach3 BOB for isolation). Just blue painters tape and mitre adhesive for workholding most of the time ✌️
@lefavour1
@lefavour1 9 ай бұрын
Thank you for the information. Keep up the great work! I run a large 3 axis machine for my day job and am in the works of building my own machine in my short amount of spare time, to hopefully get to making parts as nice as yours, some day. Stunning work, man!
@TheMadManPlace
@TheMadManPlace 8 ай бұрын
Nice - VERY nice... All your machine needs now is an automatic tool changer and a vacuum material hold down fixture and to be the ultimate dream machine. NOT saying that your machine IS NOT ALREADY the dream machine though...
@fabog3732
@fabog3732 4 ай бұрын
Which cnc controller board are you using ? And which motors ?
@gsherbs
@gsherbs 2 ай бұрын
Where did you find the diamond tip bits for engraving and what cam op did you use for that?
@Neeqone
@Neeqone 9 ай бұрын
Can you please do a video on two sided milling?
@williamnorris1516
@williamnorris1516 9 ай бұрын
Hi I enjoyed watching your video and I took some notes, the devils in the detail hey, I picked up that it looks like you set stock to leave at 0.5mm then do finishing with 0.1mm step over as in 5 x 0.1mm spring passes with feed rate of 1000mm / m neat trick I will try that out today and see if I can get those mirror finishes . And chamfers don't get me started on chamfers you set your chamfer width to 0.4mm but it looks more like 1.0mm or is it just the camera angle etc, I have been having the same thing happen on my last job I set the chamfer width to 1.0mm and it cut more like 2.0mm do you think what it does is cut 0.4 in and 0.4 down ????? I don't know what's going on next time I will do 3 induvial chamfer programs 1 at 0.2 then try 0.5 then 0.8 and run them using single block function to try and sort it out Ok sorry I got a little derailed there Mate another great video I really like that you added the speeds and feed at the start of each operation You could go one step further and add some audio ha ha Cheers Bill
@Beeeaned
@Beeeaned 9 ай бұрын
Cheers Bill! Yeah I usually run 0.4-0.5 stock as a force of habit, a lot of the stuff I do is 25-32mm thick so big stick out and risk of chatter so I play it safe, could get away with 0.1-0.2 most of the time. Running the 3f at that RPM with the low feed does cause some rubbing and heat but on my machine that’s about the sweet spot as far as finish goes, talked about it on Discord a week or two ago with some examples comparing different 3f’s too (Polished, normal, unequal helix). Around the same time I posted some pics/videos of chamfers too, the back side op probably looked larger than 0.4 because I forgot to apply the rotation and it was a little out but generally seems to do what I’d expect it to do. Didn’t really intend on doing any videos but the first one I put up after Jaymis asked if I had anything on KZbin took off so I thought I’d throw some more up, might eventually put some more effort in haha
@quasarix
@quasarix 9 ай бұрын
Love that diamond engraving with auto level, where do you get that?!
@Beeeaned
@Beeeaned 9 ай бұрын
It’s a relatively cheap (Compared to the alternatives) one I found on UK eBay, a search for “spring loaded diamond engraver” should show it up.
@jgtools
@jgtools 9 ай бұрын
Hi bro, what command you use to control your CNC ?
@MNIMWIUTBAS
@MNIMWIUTBAS 9 ай бұрын
Nice! What insert are you using for the BAP?
@Beeeaned
@Beeeaned 9 ай бұрын
Just a plain carbide APKT1135, 0.4 radius ✌️
@RateReducer
@RateReducer 9 ай бұрын
Really nice finish. What kind of aluminium do you use?
@Beeeaned
@Beeeaned 9 ай бұрын
6082 T6 - It’s the most commonly available here.
@RateReducer
@RateReducer 9 ай бұрын
@@Beeeaned alright ok, that's the higher strength stuff, that's perfectly for millig as you can see it on that awesome finish 👌
@yolowrue2582
@yolowrue2582 7 ай бұрын
How do I get in contact to purchase this? Looking to get an Audi tt 225 tranny and swap to FWD. please get back to me with info!!
@Beeeaned
@Beeeaned 7 ай бұрын
My website is down at the moment but you can throw me an email at beanedcnc@gmail.com ✌️
@yolowrue2582
@yolowrue2582 7 ай бұрын
@@Beeeaned email sent!
Transforming A Stainless Steel Bolt Into A Fully Functioning Miniature Lathe Chuck
28:44
«Жат бауыр» телехикаясы І 30 - бөлім | Соңғы бөлім
52:59
Qazaqstan TV / Қазақстан Ұлттық Арнасы
Рет қаралды 340 М.
🎈🎈🎈😲 #tiktok #shorts
0:28
Byungari 병아리언니
Рет қаралды 4,5 МЛН
УНО Реверс в Амонг Ас : игра на выбывание
0:19
Фани Хани
Рет қаралды 1,3 МЛН
Meet The Self-Made Woodworker Who Works Out of His Garage
26:35
Andy Bird Builds - CNC
Рет қаралды 2,2 МЛН
Making a simple component (CNC Milling)
8:55
CncFrezar
Рет қаралды 11 М.
14 Amazing Metal Work Processes You Must See ▶1
10:50
TechFreeze
Рет қаралды 2,3 МЛН
Homemade Rifling Machine | New Idea Solve An Old Problem
18:41
Impossible Woodturning. Unusual devices. Oak firewood. Diy.
17:44
Pavel Evmenov
Рет қаралды 11 МЛН
Turning a Cheap Mini Mill into a Capable CNC Machine
15:13
Someone Should Make That
Рет қаралды 259 М.