Looks good to me. I wrestle caliper bracket bolts with a breaker bar most of the time because of limited access preventing a full size impact gun from being used.
@Diggl3_Wiggle_49er4 ай бұрын
Ratcheting wrench for me haha works great
@kamehamehaX3004 ай бұрын
Step back and use an extension. I’m an amateur and ik that
@rYan-qo9si3 ай бұрын
@@kamehamehaX30090% of the time 1/2 drive impact with universal joint
@kamehamehaX3003 ай бұрын
@@rYan-qo9si you’re saying that’s a good solution 90% of the time?
@Diggl3_Wiggle_49er3 ай бұрын
@@kamehamehaX300 just because you think you know all going through your little apprenticeship doesn't mean shit grow up quit arguing and just use what makes UR JOB BETTER like you said your an amature trying to prove a useless point 👌
@bigp24874 ай бұрын
I still love my breaker bar and ratchet. It just reminds me of the times of working on the cars with my dad.
@abrahambarkhordar55724 ай бұрын
Aw
@alexandergunaka6664 ай бұрын
Your dad would probably tell you if there’s a faster easier way then what are you doing
@naruttaanime94713 ай бұрын
Do you put penetrant spray of a couple drops of oil a few hours before?
@bradmacgregor8722Ай бұрын
Your probably not a flat rate technician then
@tbbainter7774 ай бұрын
No mystery here. It has max torque of 250lbs. Anything in that range is its working window
@kwaynejohnson68064 ай бұрын
You'd be surprised by that thing being far further than 250lb because of corrosion etc. Sometimes it takes some serious gut strength to loosen bolts like those.
@kkswain964 ай бұрын
The right angle has 220 ft lbs. the m12 stubby & m18 compact are 250 ft lbs.
@jimmyjamessac71714 ай бұрын
Underrated
@richardrecupero43424 ай бұрын
Hurt my soul when I couldn’t even take an oil pan drain bolt off with it
@alexandergunaka6664 ай бұрын
You don’t live where there is rust and it shows
@dfacedxa4 ай бұрын
Disagree w this in 1/2 over 3/8. I feel like i can fit 3/8 sockets more places, and this thing isnt kicking like a half inch anyway. I think ttc showed that 3/8 hits harder out the gate too. This thing has saved my ass tho. Paid for itself many times.
@Tegidytowelie4 ай бұрын
It looks like it gets the job done to me. I need one of those
@brett80164 ай бұрын
I have one and I love it. Perfect for truck brakes and some suspension.
@ben10mama4 ай бұрын
In my humble opinion i prefer my capri tools flexible air right angle impact over the Milwaukee electric. Now I've just borrowed the Milwaukee never owned it but i just never felt a reason over the air version
@Enrightauto4 ай бұрын
I’ve got the Capri palm impact and right angle they aren’t bad either
@ToolsareusАй бұрын
If you want one for just power, your best option would be the cobalt 24 V. If you want to know more about it watch torque test channels video. It is a very impressive tool.
@EnrightautoАй бұрын
Not a fan of kobalt stuff
@ToolsareusАй бұрын
Did you have a bad experience with a cobalt tool? I haven’t had any break on me yet, but my favorite thing about their tools is the price for what you get.
@mosthated81903 ай бұрын
You Definitely need this in the 1/2 , I also feel as if the 3/8 of this tool doesn’t do it any justice.
@takeshi12423 ай бұрын
I use thing a lot on my car, very useful!!
@donotrobme92954 ай бұрын
That tool isn’t needed there obviously but that’s fine. I recommend this tool in pneumatic. Only way to get the torque imho
@Enrightauto4 ай бұрын
The point is to just show it in action. Having this in air isn’t any more powerful I own them in air
@A861404 ай бұрын
I love mine, it's an amazing tool
@coronadotony80514 ай бұрын
I specifically use mine on 57ft dry van trailer air bags Hard to reach top mounting nuts 1 1/8in
@Enrightauto4 ай бұрын
Nice!
@name_less76874 ай бұрын
The people that complain about them are the same people that try and use it as an electric ratchet and try to use the ratchets as impacts. Nobody with any sense would listen to them.
@Enrightauto4 ай бұрын
True 😂
@daveburn714 ай бұрын
I use mine in 3/8... great for front of engine work like water pumps and stuff.
@buttadog50734 ай бұрын
The 3/8 puts out more torque as proven by torque test channel, as long as you use 3/8 impact sockets
@Enrightauto4 ай бұрын
🤦♂️🤦♂️🤦♂️
@buttadog50734 ай бұрын
@@Enrightauto no not "🤦♂️🤦♂️🤦♂️" you're straight up wrong, go watch torque test channel, they have an insanely accurate test rig, the 3/8 puts out like 30 more ft/lbs, don't be telling people do buy inferior products
@Enrightauto4 ай бұрын
@@buttadog5073 🥴🥴 sheeple people. You should really do some research.
@buttadog50734 ай бұрын
@@Enrightauto no, you should, also project farms proved the 3/8 has more power too, they're both rated the same, the 1/2 has more instant torque but the 3/8 has higher peak numbers and given that the tool is designed to fit in tight spaces anyway I'd buy a set of 3/8 impact sockets and buy the 3/8 RA and not the 1/2
@Enrightauto4 ай бұрын
@@buttadog5073 bahahahahahaha project farm. Ok bud thanks 😂😂😂😂 now I know what I’m dealing with. Move on
@jhouzen25124 ай бұрын
I would agree with a ½ drive version. I have one myself and it kicks ass.
@youwerentthere19404 ай бұрын
I use DeWalt....should I ge the DeWalt version of this? (1/2 in = High Output Battery)?
@FUCKEDUPFAB4 ай бұрын
Ive found with mine in 3/8 the controll mode has more torque than the 3 mode witch bugs me cux i want the speed too
@f30sosa4 ай бұрын
Nice combo I use the same setup
@sugarskulllyfe58904 ай бұрын
Yea I used mine with a 3ah and it struggled on a rusted caliper bolt but once I sprayed the rest with PB blaster they all came off easy
@kq8gh9654 ай бұрын
Love mine its great
@gomezrene164 ай бұрын
Theres a high out put 6? I thought it only came in 2.5 and 5.5
@El_Diablo_LI4 ай бұрын
The M12 HO batteries only come in 2.5 and 5.0 AH sizes. But the M12 6 AH battery works just as well as the 5.0 HO. The power boost each gives the tools over say a 2.0 or 3.0 is about the same.
@Wtrxprs007able3 ай бұрын
Now i wanna see it do a late model vw group caliper bolt. They sometimes start bending my 4 foot breaker bar
@FixitFred4 ай бұрын
My 1/2 milwaukee right angle impact broke caliper bolts free that were rusted to no end in Canada on a decade old caravan which drove on super salty winter roads with only a 2.0ah m12 battery. But yes I totally agree if being a mechanic is your profession put the high output on it.
@YOUZTUBE20003 ай бұрын
So the 1/2inch Milwaukee right angle comes in M12 or is that a typo? I thought M12 would be for 3/8 and M18 for 1/2? Please clarify-- Thanks, sounds like the 1/2inch is the one to buy.
@FixitFred3 ай бұрын
@@YOUZTUBE2000 not a typo in m12 right angle impact you have 3/8 and 1/2 for anvil sizes. Both are super handy because the 3/8 is great for smaller sockets in tight spots like caliper bolts. But the 1/2 can take way bigger sockets great for suspension bolts
@YOUZTUBE20003 ай бұрын
Thanks- good to know. I didn’t realize the 3/8 and 1/2 were only M12.
@DUMPTHETRUCK4 ай бұрын
I like mine a lot, I use it Alaways to take off and on my steel skid plates on my 4runner or anything that I need to reach out with just one arm to work on. Of course it’s not a power house but it’s better than a ratchet most of the time
@asmautollc4 ай бұрын
Not sure I agree on the 1/2” part. It works great on most 3/8” applications. Use a 1/2” air right angle putting out 400+ ft lbs for the bigger stuff. I get that a 1/2” socket adds weight, but if you are using a right angle, it’s often accompanied by a stubby socket. All that being said, I mostly use it on caliper bolts so maybe it does make enough of a difference even with stubby sockets. 🤷♂️
@madjackgamingandfitness4984 ай бұрын
Yeah 3/8 is enough in opinion for whatyou can use it on. Most days for me the thing is a real pos, but it’s nice when it works in 1 out of the 100 applications. The head is too bulky for most jobs.
@redmanmr25 күн бұрын
Controversial why?
@TribalBigMac2 ай бұрын
Impressive
@zacharykarna28104 ай бұрын
How do you like those Capri impact sockets? I have tools galore at work, but was thinking about their complete 3/8 impact set for home.
@Enrightauto4 ай бұрын
They are fantastic! These are the ones I use the most amzn.to/3TV02LH
@qwedfwedf4 ай бұрын
Hahahajajajajajajaja I normally used the 1/2 inch impact for that and is so good.
@Mike-we3rbАй бұрын
My stubby 3/8 can’t break that bolt loose with a full battery. I got ripped off with mine
@The.Toaster2 ай бұрын
3/8 mid torque makes light work of brake jobs. The stubby is for most engine bay stuff imo.
@castortroy91944 ай бұрын
I don’t know about the 1/2” vs 3/8” but I got the 3/8” because the head was slightly smaller. I wouldn’t use it on anything that I wouldn’t use the stubby on.
@Danielxperez143 ай бұрын
what sockets were you using and do you reccomend the sunex master impact socket set?
@Enrightauto3 ай бұрын
Sunex are great sockets. I usually am using snap on
@Danielxperez143 ай бұрын
@@Enrightauto thanks, and yea snap on is above my budget, i just need a good starter set
@SecurityZone14 ай бұрын
Looks to me like a left angle impact
@Enrightauto4 ай бұрын
I agree
@SecurityZone14 ай бұрын
@@Enrightauto 😆
@RobertLiggett4 ай бұрын
This thing is perfect for a race car that has suspension adjustment every hour or so
@npw91312 күн бұрын
Mercedes does not require any loctite. not even anti-seize. just make sure the bolt is clean
@seanmarchiny4 ай бұрын
What’s the model number on this
@richardpatino9353 ай бұрын
My question is... How about if you use a breaker bar? You have plenty space to work with.
@Enrightauto3 ай бұрын
There is 0 reason to use a breaker bar. That’s highly inefficient. It’s the difference of a diy’er and someone who does this for a living
@electric8668Ай бұрын
Breaker bar with Milwaukee M12 ratchet works fine.
@EnrightautoАй бұрын
Awesome
@loganwork70244 ай бұрын
Just buy a right angle impact wrench extension. It lets you use your impact like an even smaller stubby impact with even more torque. Plus its cheaper.
@Enrightauto4 ай бұрын
🤦♂️
@owenpetrey11054 ай бұрын
Those capri sockets tho!
@Enrightauto4 ай бұрын
Yes they have been fantastic
@saltybuckeye4 ай бұрын
I'm sold I'm buying one tomorrow
@calebhazelwood871618 күн бұрын
What’s the difference in the right angle and the insider?
@Enrightauto18 күн бұрын
Right angle is an impact. Insider is a ratchet
@calebhazelwood871618 күн бұрын
@@Enrightauto thanks so much, love your content btw
@Enrightauto18 күн бұрын
@@calebhazelwood8716 no problem and thank you for the support!
@naruttaanime94713 ай бұрын
Do you like long neck instead of short neck?
@Enrightauto3 ай бұрын
There is only a long version of the right angle impact. This is not a ratchet
@lucascoxe14814 ай бұрын
How hard is it to use it to break the nut loose first manually then use the power to zip it off?
@alexandergunaka6664 ай бұрын
Pretty hard when your finger is on the trigger
@Enrightauto4 ай бұрын
If you watch the video again and see the bracket move you will notice they are already loose. These build up with rust on the threads and run out tight
@alexandergunaka6664 ай бұрын
@@Enrightauto Don’t worry, he wasn’t actually wondering. He just wants people to know he takes longer to do everything. People that always bring up breaking the bolts free first as if it is a religion are the same guys that will grab a ratchet to break the bolts, exhale as if work was done, gently put back in the ocd organized drawer, then grab the electric tool. Remember if it doesn’t take longer than you’re not a real or honest mechanic you’re a hack.
@lucascoxe14814 ай бұрын
@@Enrightauto ok maybe for these specific bolts. But your argument for why its needs to be a 1/2 in. and if its any good etc. 99% of users aren’t running into rusted bolts and thats what impacts are made for. If people used tools properly they would be extremely useful.. for what they are good for. Not what you want them to be good for
@Enrightauto4 ай бұрын
@@lucascoxe1481 sorry wrong video I thought this was the ratchet video not the impact video The 1/2” is for more power transfer through the anvil and the socket. Much better overall And the statement that 99% of people aren’t running into rust is false
@John-jr7xn3 ай бұрын
Capri sockets ??? Nice.
@Enrightauto3 ай бұрын
Yes they have even fantastic
@ricardogomez32054 ай бұрын
Capri sockets 👍🏻
@crackerjack81153 ай бұрын
Why not 3/8
@boostlee52364 ай бұрын
Hope you wasn't about to stand that up on the lift for it to just get knocked down
@Enrightauto4 ай бұрын
I Always stand them up 💪💪
@Honoer4 ай бұрын
Of all my Milwaukee tools I’m not saying it’s bad, It’s just the least impressive I have. lol except for castle nut bolts. For whatever reason it zaps them off with not a problem even big 1 1/2 nuts.
@connorbroyles33694 ай бұрын
I want milwaukee to make it in a m18 there sister brand rigid has it whats the hold up
@Enrightauto4 ай бұрын
Too bulky imo I don’t have much interest. The rigid only has 250 compared to 220 not worth the minimal difference with that much larger of a battery
@rc-t3k4 ай бұрын
Snap-on impacts are stronger, and milwaukee is a universal tool idea, both are good.
@emmcee4763 ай бұрын
Makes no sense to use a ratchet when an impact wrench fits in there just fine. If there's space, I go for a wrench before a ratchet
@OscyJack-4 ай бұрын
I got it in 3/8 cuz my 3/8 set goes to 27mm, and this thing doesn't have tons of beans on deck for 1/2". Imo.
@Enrightauto4 ай бұрын
More power transfer for 1/2” and bigger sockets as well for 1/2” I’ve found the battery is the biggest differentiator for sure. But I do love the sets that go to 27mm in 3/8” they are awesome. My Astro nano sets have so many sockets
@OscyJack-4 ай бұрын
@@Enrightauto I love the nanos. I got the HD variant. Those on this thing is so tiny. Good point on the extra oomph. I was torn, 3/8 seems to work in most scenarios I've found. But, there will def be "the one I couldn't get"
@Enrightauto4 ай бұрын
@@OscyJack- yea 100% the 1/2” is the same. Everyone keeps asking for it in 18v which I think could be ok. I wish they would just beef up the motor in this one and make a beastly 12v battery for the size aspect. I think 300ft lbs would be perfect
@OscyJack-4 ай бұрын
@@Enrightauto I figured I'd get the 1/2 18 if it ever came out.
@crackerjack81154 ай бұрын
@@OscyJack- elaborate
@trumanray66264 ай бұрын
Love mine she did my brakes
@Bigazzy8064 ай бұрын
Swivel socket big 1/2 gun
@mechsupernova4 ай бұрын
They WAY over estimate what the M12 ratchets can do🤣😂
@precesionnoreaster15074 ай бұрын
They just straight up use it for the wrong purposes, there's a reason air ratchets were called wrist snappers. They are direct drive tools, like come on bro just ratchet it first
@kato2182Ай бұрын
best right angle impact to have ever bin created
@witnesszer04 ай бұрын
those brake rotors look weird
@Enrightauto4 ай бұрын
Lol too much rust for ya?
@AudiTech264 ай бұрын
Id break the bolt loose first with a breaker bar and the spin it out, all that vibration is going to cause premature damage.
@alexandergunaka6664 ай бұрын
It’s not an electric ratchet it’s an impact. It’s going to have vibration.
@AudiTech264 ай бұрын
@@alexandergunaka666 i didn’t call it an electric ratchet, any power tool is going to have vibration. My small snap on 3/8 impact broke trying to take of lugnuts do the the vibration and it not being able to handle high torque and vibrating to much.
@alexandergunaka6664 ай бұрын
@@AudiTech26 So if it’s always going to vibrate then what’s the point. I bet it did I wouldn’t be taking off lugnuts with a 3/8 anything. Operator error.
@cheddarshredder65723 ай бұрын
Unfortunately the 6.0 battery is not H.O.
@malbright454 ай бұрын
Ford e-450 caliper bolt then I’ll be impressed lol
@Mr._Flunky4 ай бұрын
Or you could just turn the tire and use a 1/2 air impact and be done in less time..........🤔
@juanaguilar56323 ай бұрын
Put that thin on a rear axle
@dmitrykarkov47474 ай бұрын
That’s beautiful enough to divorce your wife for.
@dadadadankable4 ай бұрын
Okay, that’s impressive for a handheld. Those caliper bolts are always a mofo. Even on brand new vehicles. Still won’t buy it as I have the stubby, the smaller powered ratchet, and the long shaft older big head 3/8 that they don’t made anymore than shiiiiiiiiiiiits on all their old or current 3/8 powered ratchets.
@trumanray66264 ай бұрын
3/8 is best i got 1/2
@Enrightauto4 ай бұрын
1/2”
@trumanray66264 ай бұрын
@@Enrightauto i have the 1/2 and it has the same torqure the 3/8 has smaller sockets fit in smaller nuns cunts
@trumanray66264 ай бұрын
@@Enrightauto go watch a KZbin video comparison of the 1/2 vs 3/8
@Enrightauto4 ай бұрын
@@trumanray6626 I have
@boosted2.4_sky2 ай бұрын
The Kobalt and Ridgid are both better.. Milwaukee's is outdated and just old really
@Enrightauto2 ай бұрын
🤦♂️🤦♂️🤦♂️
@boosted2.4_sky2 ай бұрын
@Enrightauto I have all three.. the Ridgid is a MAC clone...☝️beast(yes, like Dewalt)