Mini Amplifier tip41 | Super Bass

[@dwtech6777]

Thank you very much friends for watching my video.. Hope this video is useful. Apologize if something is wrong with this video. Other recommendation videos: ➤ TDA2003 Amplifier Circuit 12V - Powerful Heavy Bass kzbin.info/www/bejne/pHvLZ6yfjqlkqbs ➤ DIY Stereo Mini Amplifier With PAM8403 - Very Simple Bass kzbin.info/www/bejne/iZ2ppoltg5V6mJY ➤ DIY Mini Power Amplifier 12 Volt Using transistor TIP41 kzbin.info/www/bejne/oJCXgq16qdmhb6c ➤ TDA2050 Amplifier Circuit Diagram - Very Simple kzbin.info/www/bejne/nYTVdo2Zo7ZsoZo

[@lordsagagaming9088]

Bang klo potensio nya dobel dua gimana caranya bang

[@jbssiders2621]

Dijual ga bang?

[@cristobalortega7530]

Mándame otro video

[@mktgudang9222]

what bout grounding ( phones have 4 poles for jacks and this main reason to kill IC audio in phones cause grounding if done poor can loop back current to phones and damage IC audio leaving the phone mute/deaf)

[@elirochamusicasoficial9085]

Ok

[@rolandha912]

This kind of circuit can make the speaker hot because it is connected to positive wire. Playing long will surely make the speaker to smoke and damage.

[@dhemisomsantos2999]

Cara eu fiz igual o dele. E deixei tocando por mais de uma hora e não vi fumaça nem huma.nos autos falantes e nem no capacito e nem no tipe- 41 E nem no potenciômetro.

[@jaguare3772]

Mantapp bgt , saya coba lgsung jdi , mksh bang ilmu nya , sngt brmnfaat , moga sehat sukses sllu .

[@milespeterson5049]

This circuit is so simple, but yet so powerful. I am using an FM radio kit, and on its own there isn't any amplification, so when you connect a speaker to the output, it is hardly outputting any sound. But with this circuit connected to the output, the speaker is now much louder, thanks. 👍

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@luistomala353]

Transistor tip45 Resistencia 1k Capacitor 100uf 16v Potensio 100k Jumper

[@davidzkorn]

Can i use TIP31 transistor brother? Or not .. ?

[@Ok-wl5bt]

Can i use a 50k volume controller

[@giwaependi]

Terima kasih banyak telah berbagi ilmu, sangat bermanfaat, tlah kita praktekkan hasilnya memuaskan bisa pasang di leptop maupun hp, volt nya bisa pakai power beng juga , smoga Sukses Ngan aminn.

[@dwtech6777]

oke, saran hanya untuk percobaan tidak dianjurkan penggunaan dalam jangka lama. kalau mau pemakaian sehari-hari bisa pakai TDA7377 kzbin.info/www/bejne/aJy5nWCvjKx_e9E

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@abdulmajidmahvy2909]

I TRIED THIS, GOOD AUDIO, THANKS, I AM FROM MUMBAI, A RETIRED CHARTERED ACCOUNTANT!

[@dwtech6777]

Great 👍

[@iveedd]

Is it loud sir?

[@Radbula]

I built it and it's not worth the trouble, works like regular 5W. But I respect you for your hobbies

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@daxsax]

Cuantos watts entrega max?

[@Random_4400]

At 5v probably not more than 5w

[@kennmossman8701]

For such a circuit NO specs are given - very strange - maybe he does not know. Many ask how much is the output power; the formula is Wrms = [Vs - Vce] / 2 / Speaker Impedaance so for 12V and an 8 Ohm speaker its barely 1/2 Watt[rms]. In the comments he says 10W which is nonsene. WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@marcosvinicio8794]

Pode substituir o tio 41 para o tio 31C ou 13003?

[@SERVISLAPTOPJOGJAPRO]

Jalur dari sumber audio out jack, harusnya masuk ke ground dan kaki pinggir potensio, bukan kaki tengah potensio. Kalo masuk kaki tengah potensio, di posisi volume minimum audio out dari jack akan ter-short. Output jack audio tdk boleh di short. Kaki tengah potensio harusnya masuk ke kaki minus Elco (koneksi kaki - elco dan + jack terbalik).

[@dwtech6777]

terimakasih atas koreksinya kk 🙏

[@sarifudinbaharsah3367]

Coba gambarin skemanya?

[@momazosyorick6059]

If my jack connector has green, blue and red, how do I connect them to the potentiometer?

[@dwtech6777]

look for ground and audio input

[@adaomartinsdasilva]

Bom dia. Pode usar um resistor acima de 1k?

[@foxi4002]

Também estou com está dúvida amigo

[@Random_4400]

Very nice, I'm guessing the topology is class AB?

[@dwtech6777]

Yes, it is

[@สุมลเพียรดี]

ชอบดูครับได้ความรู้ดี

[@kennmossman8701]

WARNING WARNING WARNING this is a very bad design which can/will DESTROY your speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@elizabethkinnear8479]

Can I use TDA7377 as well

[@jorgearmando2506]

Excelente, se lo puede conectar a 12 voltios?

[@khairulazharnst389]

good, the higher the voltage, the cleaner.. but you have to use headphones so that the heat doesn't get too much

[@ikilyou1b]

⁠@@khairulazharnst389more transistor?

[@godfather9892]

It's working perfectly......thank you ... can I make 3 channel with tip41c

[@dialrigaMc]

Una preguntas cuantos voltios re ciste, es que yo tengo 2 parlantes 25 w quisiera saber si ese sistema sirve para para conectar los 2 parlantes ?

[@dwtech6777]

5 voltios, si desea utilizar 2 altavoces, utilice 12 voltios con un sistema estéreo. mira el video aquí kzbin.info/www/bejne/pJ24mnWpp7N0eK8

[@wiliamesanfoneiro7923]

Sera se da pra usár em duas caixas de som doméstico?

[@tarcioch]

Muito legal seus vídeos,simples de entender até para quem não intendi nada de eletrônica como eu! Seria possível fazer um vídeo enssinando como construir um mine amplificador para guitarra? Obrigado e parabéns pelos vídeos!

[@dwtech6777]

Obrigado por assistir. muito provável

[@fg_jk5930]

Fiz um com dois 13007 e uma fonte 2.4 amp 24voltz forte pra caramba pena que toda vez que liga o falante sobe

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@thanhcanvo5690]

Ad cho hỏi có Transistor 13003, Tụ 16V 220uF, R 1k ohm thì ok không?

[@thanhcanvo5690]

Mạch trên thử 2 loa 3W hát ok bạn.

[@dwtech6777]

use NPN transistor

[@raimundononatotim7454]

Obrigado por compartilhar seus conhecimentos isso é bom de se ver 👍

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@คนให้โอกาสคนคือยอดคน]

Our capacitors are type 100.uf-50v ..Can it be used interchangeably?

[@dwtech6777]

yes u can

[@คนให้โอกาสคนคือยอดคน]

Thank you

[@filenotfound__3871]

Soo: when u turn the potentiometer to lowest volume u basicly short across your audio input?

[@SERVISLAPTOPJOGJAPRO]

Yup, misplaced connection among audio in, elco and potensio. + Audio should be swap with - elco on potensio.

[@BuluBuridSMDA]

@@SERVISLAPTOPJOGJAPRO Ada skematiknya yang benernya 'masgan 🤔? Newbie pengen belajar rakit buat bass ndentum gleeeerr ..😅🙏

[@taikong7952]

thank you. tip41, how is the stereo circuit?

[@pulpo439]

¿Cuántas veces amplifica la señal de entrada? (más de 3, ya és válido). ¿De NO tener a mano ese Tr, ¿Cuál sería el mejor sustituto, (equivalente)?

[@RFF097]

IRFZ44N

[@NuriawanWelder]

Ada mslh ini kang dr tutor sampean yg sy pratekan di rmh, klo TIP 41 sy psg yg 42 bermslh gk trs, untuk speaker bks tv kan ada dua tuh L R, yg L ada kbl mrh dan htm, yg satu lg ground coklat 2 2nya bgmn cr mengkonekannya di jlr speaker, satu lg kbl untuk jek punya sy yg biasa untuk ke hp dan RCA speaker kan ada 2 cbg tuh pink ground dan pth ground bgmn itu mas, sy konek kok gk keluar suaranya lagu yg dr hp

[@santowalterscaramella6323]

Obrigado. Como fazê-lo ser para um canal filtrado só de graves ou só como woofer? Por favor.

[@dwtech6777]

Obrigado por assistir, Este é apenas um exemplo, não é bom a longo prazo

[@RicardoHernandez-gy8ev]

Hi ! I have a battery powered portable amplifier that I use for busking. It has a subwoofer, Q: Can I put this amplifier you made as a preamplifier and give it more punch?

[@radensuryo.h.n9896]

Well,,, this is like this even without talking,what I like is very detailed.What I want is a series like this,but complete with potensial volume,bass and treble. If can please make it like that. Thank you very much for you knowledge,I wish you a long and healthy life success.

[@dwtech6777]

Thank you for watching

[@kylermatheny6481]

Yeah it would be cool it it had it all with it instead of just the bass

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@valtenirsb6401]

Essa fote é a mesma do carregador do celular ? Ela é de quantos volt ?

[@dwtech6777]

sim, 5 volts

[@genesmith482]

I know these are simple circuits but PLEASE show schematics.

[@masdani2155]

Mantap basnya gelerr 😀😀👍👍

[@masdani2155]

Tip 42A bisa bang

[@dwtech6777]

bisa bang

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@alejandroperez8968]

Hola muy buen video pero cuántos parlantes puedo ocupar y de cuántos wats o ohm

[@dwtech6777]

Gracias por ver. Altavoz de 10 wats 8ohm

[@alejandroperez8968]

@@dwtech6777 con este sistema puedo utilizar solo 1 o puedo conectar 2 a la misma vez

[@alejandroperez8968]

Seguí tu tutoríal y no me funcionó 😭

[@kennmossman8701]

@@alejandroperez8968 WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@kennmossman8701]

@@dwtech6777 lmao what nonsense Wrms = [Vs - Vce] / 2 / Impedance so for 12V it is not even 2 W

[@KhushiShah0214]

Can it work with a 1000uf 25v capacitor

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@OscarGutierrez-jy1ij]

Gracias por compartir tus conosimiente en sonido. Lo intentare hacer.👍. BENDICIONES.

[@kennmossman8701]

WARNING WARNING WARNING this is a very bad design which can/will DESTROY your speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@prashanthkumarvadyarapu6576]

Can i use L7805cv transistor

[@ALPHALabs02]

If you have an analysis how it work, your video is wonderful. It is helpful for audience. Thank you

[@dwtech6777]

Ok, thank you

[@электро-лис]

Хрень. Самый обычеый усилитель на 1м транзисторе и подтягивающем резисторе. При чем недоделана схема.

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@eilacagayon6957]

Is that ok to use 9v battery?

[@dwtech6777]

yes

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@eduardomarin33]

Hola muy buen video una pregunta se pueden conectar 2 altavoces?

[@Oscar-kv8vw]

Podrias conectarlos, pero recuerda que la potencia se enviara a dos altavoces, por lo tanto la potencia disminuirá dependiendo los altavoces

[@eduardomarin33]

@@Oscar-kv8vw de que capacidad es el altavoz que utiliza en este video

[@sookdeofamily9334]

In the beggining whats that big piece

[@juanpasinche4023]

Interesante el proyecto 👍🏻, y si lo quisiera para amplificar sonido ambiente poniendo un micrófono, cómo lo haría ? Te agradezco tu ayuda 👍🏻

[@jonascrookedneck5487]

AA

[@audiotoxico]

Distorciona de esa manera ??? O solo es por el micrófono??

[@kangbahar170]

Great sharing....👍👍👍👍mantap gan.. auto sub...

[@hingpistv7036]

Hingpis tv..

[@kennmossman8701]

WARNING WARNING WARNING this is a very bad design which can/will DESTROY your speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@zunarjibriel3500]

how do you connect it with a 12 volt dc bluetooth mp3 with 2 speakers?

[@FebrianRizkyRamadhan]

Luar biasa menginspirasi... Kreatifitas josss.. Thx masee motivasinya🙏

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@kylermatheny6481]

Is there a way to make it for a car so u can have it plugged in to the car and plugged into ur phone

[@GonzagaCustom]

Salve Mano Fiz o amplificador mas não sei porque ficou muito baixo Mesmo anulando o potenciometro

[@danubio1841]

Você usou 5v ou 12v? Dependendo da tensão e tbm da amperagem o son vai sair baixo mesmo.

[@danubio1841]

Mas esse amplificador é. Um classe a então não pode ter muita tensão no falante se não queima a bobina.

[@supinisreal9150]

Usb - white or pink?

[@dwtech6777]

pink (+) white (-)

[@reskyopransyah8197]

terimakasih bang sudah mau berbagi ilmu sukses selalu💪

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@dwisetiani9609]

Is it true that the 40 watt speaker is strong?

[@FunkyDisco79]

Yes, the 40 watt speaker can lift a cow.

[@luishenrique3450]

otimo video!!! quantos autofalantes desse da pra ligar ?

[@dwtech6777]

obrigado apenas um

[@vyakhro2334]

I am still not convinced because the sound quality will somehow depend on the recording device you have used and also the device use by the viewer.

[@sathishsathish6074]

We can use 2200 uf 25v capasitor

[@joseraucci9953]

Tank you, i make is project. ❤️❤️

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@ogietechvlog3912]

nice tutortial video sir its very simple DIY bass amplifier i've learn this thank you for your sharing this video.new friend and subscriber. 💯%❤full support your channel.god bless.😇

[@luisgermanromero3105]

por fabor responder en esta clase de circuitos nunca dicen los vatios de las resistencias 1/8 1/4 1/2 o 1vatio cul sera?

[@ekopujiyanto9181]

jangan asal colok ke hp.kalo gak mau hp rusak.heheheh😂😂😂

[@dwtech6777]

pakai bluetooth receiver

[@ekopujiyanto9181]

iyapp.right

[@antoniopires1839]

legal não sou escrito mas gostei ..........................................................................................................apo

[@dwtech6777]

Obrigado por assistir

[@Aprendiendofacilacamacho]

Muy buen video y fácil de hacer 😎👍

[@kadang490]

can it be put on a wooden stick or make a place?

[@markanderson8066]

The aluminum block is the hear sink for the transistor.

[@wayandiana8110]

input audio di potensio kok masuk pin out ya?

[@newtronschanell6954]

gak masalah tetap bisa

[@renrose5135]

Is it heatsink use as a board?...

[@НастяЛебедева-ш9м]

*Вот ты крутой электронщик! Такую серьезную схему собрал.*

[@Son_of_Khan_Family]

Mono or stereo?

[@dwtech6777]

mono

[@andresmirandamilan5406]

Con un potenciómetro de menos ohms hubiese funcionado mejor creo

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@vladimirmazare7363]

Achei bom este amplificador por favor me diga quantos wats de potência ele tem ?

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@andyfirmansyah8110]

Thank you so much for this content 🙏

[@dwtech6777]

Glad you enjoy it!

[@raultorres2305]

Hasta cuantos ohmios del parlante soporta?

[@engkushidayat6568]

Kl colok langsung ke gitar elektrik bisa kenceng ga

[@mktgudang9222]

can we use it to amplify it to a cheap speaker like fake JBLs ( poor man portable amp scheme)

[@unknownuser1758]

Thanks for the help dude

[@dwtech6777]

Happy to help

[@felipecosta6794]

Da pra ligar em um toca CD?

[@Cloverboi]

Works fine with a NPN BD243C

[@maulanarevydo4343]

Tutor nya mantab bang semoga dilancarkan rezekinya

[@dwtech6777]

amin, terimakasih

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@rahmatwahyudi9627]

No hoax, this real projec god bless for you txs

[@heraldomarques5057]

7

[@heraldomarques5057]

Jj

[@gustavoordaztoledo3204]

Habrá algún problema si le pongo un capacitor de igual de 1000 microfaradios pero de 24 voltios ???

[@dwtech6777]

No hay problema

[@electronicshelpcare]

Nice circuit diageam

[@kennmossman8701]

WARNING! WARNING!! WARNING!!! this is a really bad design which can/will DESTROY the speaker. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@alibiechannel2011]

can you install it in the car or not ?? DC 12V?

[@dwtech6777]

this is simple version amplifier, not recomend use a long time :)

[@masdani2155]

Tip 42A bisa bang

[@nengrahayu3041]

kl di kasih tegangan 12 volt bisa gk Bang?

[@sharatchandr6945]

Lie, NO BASS SOUND

[@rodrigodias5841]

Posso usar um transsistor 13007 no lugar do TIP41?

[@celimaroliveiradealmeidaal424]

Maravilhosa 👍👍👍👀👀👀

[@alessandropaiva2284]

Funciona mesmo?

[@MargaritoMartinezCuervo]

I did it, and it works well...just the pot not control de volume, it works like on (music yes) or off (no music), but the sounds is very good. thanks for sharing.

[@dwtech6777]

Thanks for sharing

[@valdivinosilva2014]

Estou adorando seus vídeos Parabéns

[@dwtech6777]

Obrigado por assistir

[@luisavalos8011]

Muy lindo el sonido pero cuantos w r.m.s tiene es para mover un teléfono solamente?

[@dwtech6777]

Gracias por ver

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@gleiceanebarrosdasilva9488]

Ei! Eu fiz e funcionou, obrigado por Postar cara ficou alto e muito bom dr mais .. Eu dhemisom comentando ficou da hora E que meu celular pifou mais o mini amplificador ficou top.. Fiquei muito feliz quando saiu o audio;

[@AdenilsonPeruchi-n1w]

O projeto queimou seu celular?

[@lucasabreu8932]

Hello. What output power do you have?

[@pinkartnail]

You can visit my KZbin channel: kzbin.info/www/bejne/d5rLcoqlprh8kKs

[@severinonazario8596]

Muito legal parabéns

[@dwtech6777]

Obrigado por assistir

[@sweetsinner-sh3eu]

Buenas tardes amigos tengo una pregunta soy nuevo en esto pero quiero hacer un amplificador con partes de un stereos me pueden ayudar xfavor

[@JoAnSoSaOficial]

Yo te ayudo

[@kennmossman8701]

WARNING! WARNING! WARNING! this is a really bad design which can/will DESTROY the speaker. Also there is no Av - its just a current booster - it is not a proper Amp - output power is very limited.. I recall this circuit being published 30 years ago as a noveliy with the author warning it was likely to damage the speaker. It also suffers from low S/N. This circuit has appeared on several 3rd rate video channels - clearly this guy just copies without any understanding.

[@alexsalas8083]

Funcionó al 100

[@miniengineer7133]

bass be like .mujh se nahi ho payega 😂

[@komariahkomariah2293]

Is speakers same to jbl xD

[@dipaofficial123]

Sir, that's using tip 41/42, bro, if you make 2 transistors of the same type, can you do that, bro? So, how much is the maximum resistance allowed?

[@dwtech6777]

tip41

[@umargul5644]

Great job sir, thanks a lot

[@njtuner3880]

Mbelgedese ukuran piro kui maak?? Speakere merk entut singo... Banter ora geber iyo