MINI ATV First Drive and Metalwork! | Monster Mini ATV Part 2!

After our last last episode, the ATV was looking disproportionate, so we added some tubing to simulate fenders as well as some stunt ATV inspired side steps. Once we finished up the cosmetics, we took it out for a rip. We were super impressed with how the suspension absorbed bumps and the handling. The electric start Tillotson from GoPowersports packs plenty of power for this tiny frame. As always, the links to all the parts we used are down below! Special thanks to RogueFab for sending us a VersaNotcher to help us step up our fabrication game!
RogueFab tubing notcher:
www.roguefab.c...
Thank y’all for watching and be sure to stay tuned for the next step of the build, where we do some more driving and performance mods!
*Be sure to check your local laws before driving any non-registered motorized vehicle. Do not attempt these activities at home. All content produced by Build Break Repeat is for entertainment purposes only*
---------MUSIC --------
Music - Background and Montage Music Is From Endemic Sounds
www.epidemicso...
Intro - Jimmi by Andrew Applepie
• Andrew Applepie - Jimmi
-----------MERCH------------
MERCHANDISE CUSTOM DESIGNED BY YOURS TRULY
teespring.com/...
--------------TOOLS------------
RogueFab tubing notcher
www.roguefab.c...
Pro-tools tubing bender
pro-tools.com/...
Optrel Crystal 2.0 Welding Mask
usa.optrel.com...
Optrel Grinding Mask
usa.optrel.com...
-----PARTS-----
Electric Start Tillotson
-www.gopowerspo...
ARC Billet Rod
- www.gopowerspo...
RLV Muffler
- www.gopowerspo...
Header Pipe
-www.gopowerspo...
Top Plate
-www.gopowerspo...
Hot265 Camshaft
-www.gopowerspo...
Mikuni Carburetor
-www.gopowerspo...
Gold Chain
-www.gopowerspo...
Shocks
-www.gopowerspo...
Axle
-www.gopowerspo...
Axle Bearing Kit
-www.gopowerspo...
Locking Colars
-www.gopowerspo...
Sprocket
-www.gopowerspo...
Sprocket Hub
-www.gopowerspo...
Brake Disk
-www.gopowerspo...
Brake Caliper and Lever
-www.gopowerspo...
Tires
-www.gopowerspo...
Wheels (Rear)
-www.gopowerspo...
Wheels(Front)
-www.gopowerspo...

[@menno729]

Idk why this channel still hasn't hit 1 Million subs, like its quality content!

[@jaredmcquiniff5362]

That mini quad is sick! The metal work y’all did looks great and the performance is absolutely perfect for something that small! Great job guys

[@bobwhite5440]

suspension looks like it works well on road and in the dirt. it would handle better and be less likely to tip when turning if the front suspension was modified to produce a negative camber curve during compression (i.e. when making a left turn the right front suspension will compress and needs to produce negative camber which will allow the tire to dig in for more grip and produce more stability). moving the inner pivot of upper control arm lower may be enough to do it or it may take more changes as well. a lot of variables involved. keep up the good work.

[@motomule]

Big fun in a little package!!

[@jamesmcgee9279]

Might want to throw a stiffer adjustment on the rear suspension! Nice job guys!

[@maxxproductions7749]

You guys are pretty professional quality I’m sure If you took custom order stuff it would be a hit!

[@bradleyj.fortner2203]

It's underpowered or under-geared. If it won't wheelie, it should do a burnout. It doesn't do either.

[@tristanbennett6007]

Suspension to soft my guy

[@ahnurmom_187]

looks so fun to ride! with that tilly and the mods on it it rips!

[@tankdestroyer101]

Kinda sounds like it can rev higher. Super dope build looks fun 🙌

[@mingusbreeze]

Thanks, guys.

[@samsgarage1716]

I put a 212 on a mini atv for my daughter and she loves it.

[@bryduhbikeguy]

Another awesome win guys!Maybe when on road racing you can put some wheel spacers in front for even more stability.I like the way they set for off-road,being a hint wider.Will you throw on a set of meats and run this up in your hill trails?That thing will Fly once you're comfortable running to it's limits.Happy Trails !

[@gooberclese]

I just got a 125 Chinese little 4 wheeler I'm thinking of doing this to. I only need it for yard work and yard sale cruising so that would be perfect. Nice build.

[@RustyIronGiant70]

Great build guys that thing is tiny fantastic.The suspension looks a little soft in the rear and you should get a "Juggernaut" from GoPowerSports to improve your takeoff and top speed. Love your content Guys. Great job. Looking forward to what you bring next.

[@BuildBreakRepeat]

Juggernaut and comparison video will be out soon!

[@jurriendw050]

Do power upgrades little too underpowerd for me

[@BuildBreakRepeat]

Power upgrades coming soon...

[@samuelrecicar1576]

Looks sweet.

[@dennisleger9229]

We’re so excited ( most boring tone ever)😆

[@Tampaboys]

Looks great guy's. Ride's really nice to looks like a fun lil quad I need to finish mine so I can rip it around

[@RogueFabrication]

Awesome video guys. It does look way more complete with the bars added. And it's probably safer too.

[@BuildBreakRepeat]

Thanks, looking forward to putting the notcher to work in the future!

[@xkillajay]

You should tack on some diamond plate for the fenders that would look sick

[@jefflarson4117]

You built the ultimate motocross pit bike!

[@BigRichEHhthang100]

great job guys

[@urcoldkiller6231]

I want this thing so bad. It bad ass

[@calvinwright1816]

The filming quality is perfect 👌 sick build 👍🙂

[@cadentilton8072]

You should install the front brakes some of these mini quads came with, then you could use them as a form of launch control so you could wheelie (hold the front brakes then apply just barely not enough throttle to push through the brakes and then let the breaks off)

[@ronniewilliz153]

Killer build

[@liambrewer7751]

You should stand on the back bars and do a big wheelie

[@ollilehtonen6764]

Shorten the rear fork by three quarters of an inch and stiffen the suspension by 30% and you've got a mad wheelie machine with easy control over the angle.

[@lechkenassh9008]

those 50cc quads just go for a bigger rear end gear 32 tooth and 60 mph on road. and more teeth for off-road and build a box for the extra gear and chain and tools for all situations !!! or the 125cc quads and the same but a jack shaft to get 7or9 to 1 and lawnmower tires on the rear end. and same extra gear and chain for off road use. both set-ups should hit 60 mph= depends if your willing to hold on in the end. and the 50cc quad has skinny rear tires from a snow blower for hardness (and 3 inch wide fronts are stock)!!! and the lawn mower rear tires(fronts are stock) auto level after 30 mph and hold on !!! And a good road/trail the front last a while 1500 miles if shocks done right so when you sit down the tires stand up right and not leaning or turning. for speed and gas economy !!! At least that is how I build then with a 212cc or 420cc but with the chain clutch #40 chain !!! and stock motor straight to the governor and by pass al the rest to get 7000 rpm stock. just needs lots of air !!! to cool it in the higher rpms. and some 2 stroke oil in the gas for the higher rpms. to save the motor !!!

[@nicolec7290]

The tires are the best

[@billsemailis]

It looks like your barstool racing.

[@jimmyflint6153]

Where u get them wheels and tires

[@theogarner2833]

Nice build I’m chopping up a 50cc quad and throwing a 212cc in it wondering where u got the rear axel setup?

[@seanclarkminikartgarage1616]

Should add a led light bar on the front

[@jonessjunk144]

What size wheels are those? I found plenty of street tires for the 6in but none for the 7

[@mindovermatter3988]

Hey guys i build alot of these quads specifically the model you have. They're are many variants of them from diffrent chinese manufacturers. Tao tao, roketa, coolster, boyang, etc... Many more but the point is i have the same tires the same exact type of quad. Ata110b-ata110b1-3050b and all other simalar models. They sell nitrogen shocks at t bolt usa with motora that bolt the factory engine mount. All the way up to a 4 valve 190cc i highly recommend checking them out. Im pretty sure you guys know cars & camera's, they have also had a mini qaud & if you check all chineae atv's, pitbikes, pocket bikes. Etc all use the same engine bolt pattern. They can fit a 49cc Chinese honda clone all the way up to 125cc, bolting in of course. after that the 140cc with require you to extend the frame but good work i hope to come out and have some fun with the quads at a meet maybe.

[@mindovermatter3988]

I forgot to mention the various amounts of aftermarket parts you can get for these things that are extremely cheap but that's too much to say here

[@joshuabynum4456]

What did you use to extend the rear axle?

[@ipad1729]

Imagine custom wheelie stunt quad

[@jaredstone6666]

I’m doing the same build. I have just one question how did you weld up the axel?

[@gooberclese]

Solid axle swap I bet. Probably a Go Powersports set up as he mentioned getting the break lever from them. Those guys have EVERYTHING gokart or minibike.

[@botskifani22]

whats the orginal frame

[@snowdad90]

Forsale???

[@nsk6914]

What type of welding machine is this

[@Hochodo]

Paint ideas?

[@Dave96z34v2]

Heads up! For some reason none of videos on your channel that I subscribe too have been showning up in the last 4 months in the news feed.

[@BuildBreakRepeat]

Do you have our notifications turned on to "all"?

[@Dave96z34v2]

@@BuildBreakRepeat how do I change that setting. Another strange thing is in missing a bunch of channels as on my list.

[@BuildBreakRepeat]

@@Dave96z34v2 If you click on the bell icon near our channel name, it should have three notification options (All, Personalized, and None)

[@Dave96z34v2]

Crap I miss wrote the first comment. So yeah my youtube mysteriously unsubscribed to your channel and 8 others that I have found missing so far.

[@dkendrick652]

It looks awesome, but it really needs floorboards. You're running the risk of a foot falling off of the nerf bars and getting trapped between the ground and the bar. Your foot placement looks really sketchy.

[@BuildBreakRepeat]

True, We ordered some ATV nerf bar netting that we'll be installing in the future

[@zxggwrt]

I came here to say the same. Looks great but it could mangle your whole foot! Keep up the good work!

[@jonessjunk144]

I have a chinese quad with stage 3 predator and tav and I can't keep the front wheels down from 0-20 mph. Might be your gear ratio

[@jonessjunk144]

So dangerous I had to weld willi bars on to keep my friends from looping it

[@TwoBroLawnCareWI]

What sprocket size in back did you use and did you use a clutch or torque converter

[@jonessjunk144]

Its got a torque converter with HD yellow spring in the driven with a juggernaut driver 44 tooth rear sprocket and 12 front on 420 chain and genuine comet belt the chinese one get destroyed in about 10 minutes

[@666slotki]

V max?

[@lawrenceorum6030]

Looks like ur left tire out of line I think lol

[@inspireonex]

Braptor.

[@ipad1729]

Dude put a 425 or what ever it is in it then it will wheelie

[@tristanbennett6007]

Suspensions to soft

[@perry_motorsports4104]

That thing is slow as hell, even my 110 will wheelie and burnout no problem. What is this a 49cc Ebay motor? Lol

[@Gone_rn]

Not too impressed with the tillotson

[@lennym1273]

Bars way too wide, looks goofy...

[@pa6390]

slow

[@ryanbonzagni2299]

What is that tubing bender?