Thanks for the review. I don't mind the silent film, especially since you showed teardown photos. Awesome!
@user-ho7zh5yh3e2 жыл бұрын
Хорошее видео с реальным измерением сопротивления резисторов. Спасибо !!
@Baerchenization7 жыл бұрын
What are you trying to say?! :) 30 minutes ago, I didn't even know there is such a thing as an insulation tester, but after watching 3 KZbin videos, I feel totally confident to use it around the house :)
@ashvanbro93292 жыл бұрын
Just bought one nice bit of kit
@birdking63894 жыл бұрын
It should be good for industrial simple AC motor testing. I bought one years ago but never got a chance to use it.
@lyndonjosephrealubit38922 жыл бұрын
How to use this for ground fault detection locator?
@user-cm1fc7or2t4 жыл бұрын
👍
@poolrodrigogallardoinuma7037 жыл бұрын
¿de que tamaño es?
@edwincatacutan52774 жыл бұрын
So you basically cannot measure 0mega-ohm with this? Thank you for the reply.
@ScreggaeaficionBw Жыл бұрын
one wire in the earth and one wire in the R-S-T.
@sikkepossu7 жыл бұрын
When you tested the connection between earth and solder tip it did not display "short". I displayed 1.7 mega ohms! So, why said it was showing the correct value?
@bjornroesbeke6 жыл бұрын
Because it won't go any lower, even when having both leads directly connected. It's a measurement error but because the LCD showed 1.7 MOhm, the user assumed it to be 0.
@brianwoodard2337 жыл бұрын
ti is silent laugh!
@cyrildelacruzjr43653 жыл бұрын
Hmm
@kerimaltinok23688 жыл бұрын
thanks for the video I'll stay away from it hahaha probably it's better to spend another 200 300 bucks to get something better for the long run and more accurate testing etc.
@user-kb8pv5cw3k7 жыл бұрын
בס"ד לא ברור לי א) אין הסבר לדגם UT501A ב ) לא ברור לי מתאי בודקים בנקודות החיצוניות ומתאי בפנימי
@seandempsey93963 жыл бұрын
1 on left of display means over range that is more than the instrument can read that is a good reading, if you test live and neutral you should get the same reading if the soldering ion is in good condition, if you press the test button with the leads not connected to the the ion you'll get an open circuit and 1 will be displayed on the left of the screen short the leads to gether and the meter will read 0. The minimum value the meter can read is what the manual says this refers to the resistance of the circuit you are measuring. If you get a reading less than 1megga ohms then the circuit or appliance must not be used as it is unsafe. I am an Electrition so I know what I am talking about the test instrument is a great tester for some one who is new and starting out in the electrical industry I have been using uni-t testers for 15 years and I have never had any problems with them.
@fnpfar11 жыл бұрын
No push button? This is so dangerous!.. If you touch by accident the probes you can die.. It should to had an push button so if you receibe a discharge , you will be able to stop by pulling off your finger.. Well sorry my bad english..
@fernandojara19993 жыл бұрын
Mudo ctn
@brianwoodard2337 жыл бұрын
silent films we do not like !
@NoMercy19007 жыл бұрын
Well go make your self one with sound ;)
@blackterminal8 жыл бұрын
Another video where no one talks. Please if you dont speak english then just load it in your native language. I dont understand the desire for silent videos. :)
@davidprice28616 жыл бұрын
Something wrong with your leads, short should show nearly 0 Ohms not 1.5 Meg Do you know what you're doing? If not, please don't post, you could cause death or injury.
@NoMercy19006 жыл бұрын
David Price No nothing is wrong with the leads, this is not a Ohm meter, it is a insulation tester, and it has a minimum ohms reading, and now... Do you even know what you are talking about? If not, don't post garbage in the comments and mislead people...