Single Mosfet Mini SSTC Tesla coil with 10 + cm Spark

This project is sponsored by PCBWAY www.pcbway.com...
Only $30 for an SMT prototype order. Free shipping & free stencil.
You can make this miniature and simple Tesla coil in less than a day along with winding the secondary coil which contains only 500 turns. In addition, the final result is surprisingly good with a generated spark with a length of 10cm and more and relatively low consumption, especially when using the Staccato controller.
SAFETY NOTE: Please do not attempt to recreate the experiments shown on this video unless you are familiar with High Voltage Safety Techniques! Direct Current even above 60V maybe lethal, even when the AC supply voltage has been disconnected due to the stored energy in the capacitors. I have no responsibility on any hazards caused by the circuit. Be very careful. This is a humble request.
Detailed instructions, pictures, and schematic at :
www.hackster.i...
Chapters:
0:06 Short Demo
1:30 Description
2:42 Parts
6:10 First test and tunning
9:20 Demonstration
10:12 With Staccato interrupter
12:00 Staccato + SCR Regulator
13:58 Conclusion
14:51 Building
If you are interested in this area, see the Playlist at:
• High Voltage
If you like my job buy me a coffee: ko-fi.com/mircemk
Visit my KZbin Channel for more Projects , DIY and How To Make videos:
/ mirkopavleskimk
by mircemk
SUBSCRIBE LIKE AND SHARE !!!!
Thanks for your Support !
#highvoltage #teslacoil #mosfet #pcbway

[@electronics.unmessed]

Hi Mirko, I am always enjoying your DIY projects very much! Thanks for sharing. I am always wondering about the RF interference of the Tesla coils. Could you elaborate a bit on that, especially in the short wave and UHF range?

[@electrogravlabs]

Please do

[@samj1012]

Please add audio modulation. Great channel

[@gerd3136]

Amazing, thank you!

[@someguy5971]

Very nice video once again! Although it would have been also interesting if you showed the heat difference using the special thermal camera that you demonstrated in a previous video, but overall very nice!

[@MirkoPavleskiMK]

Nice idea, thanks :)

[@Wicak_s]

Amazing❤❤❤

[@realityforecast]

Fantastic!

[@BlazenWinchester]

Build a slightly larger one, making a video of step by step instructions

[@Mrjjjjjj]

Hi sir, where in mosfet you connected the interruptor?

[@MirkoPavleskiMK]

Between Gate of Mosfet and GND

[@Mrjjjjjj]

​@@MirkoPavleskiMKis there any other change i need to make in tesla coil if i connect interruptor?

[@helicopterkin1607]

Can u1560 fast diode be used to replace u1540?

[@MirkoPavleskiMK]

Yes

[@helicopterkin1607]

@@MirkoPavleskiMK What types of capacitors can be used? Is it possible to use polypropylene capacitor or mkph 450v capacitor?

[@MirkoPavleskiMK]

@@helicopterkin1607 I use MKP capacitor

[@helicopterkin1607]

@@MirkoPavleskiMK but in my place I only have cbb22 capacitor and the new electrolytic capacitor is 1uf,400v the rest is not there, can I use it?

[@MirkoPavleskiMK]

@@helicopterkin1607 You can use 1µF/ 400V electrolitic capacitor

[@cisarvialpando7412]

What can I use if don't have that transformer ballast...

[@MirkoPavleskiMK]

You can use primary from 150W standard E-type transformer

[@Wicak_s]

Does the circuit use AC or DC electricity?

[@MirkoPavleskiMK]

It use pulsed DC, one diode + small value capacitor

[@cisarvialpando7412]

How