Missing Items Using Two Tone Ferrous? Follow These Simple Steps | Tips And Tricks | Metal Detecting

Hi, Im Liam , a Metal Detectorist ( not a treasure hunter) , and a tester of Metal Detecting machines, with a utube channel.
The channel delves into how to detect with hints and tips , settings plus the obvious, SEARCHING FOR HISTORY.
Metal Detectors owned or once owned
Nokta Legend
Minelab Etrac
Nokta Makro Simplex
Xp Deus 2
Garrett Ace 250
Teknetics Eurotek Pro
If you enjoy the content , please subscribe (absolutely FREE), don't forget to hit the notification bell so you don't miss out on future vids.
Your support will be much appreciated.
🛑FOR ALL YOUR DETECTING NEEDS🛑
10% OFF MOST PRODUCTS AT
spinadiscmetal...
Using Code HISTORYREVISITEDUK At Checkout
Metal Detecting Merchandise
www.digwear.co...
History Revisited Merchandise
www.merchandis...
Facebook Group
Metal Detecting Life - History Revisited
/ 1063885334216384
I really appreciate my subscribers for following me , it means a lot. To show my thanks I will give you all a chance to win some prises as often as I can.
#metaldetectortesting #minelab #metaldetecting

[@Iaincrosby]

Great machine in its time - I had great success with the FBS machines back in the early 2000’s. The thing is, technology and performance has moved on quite a bit, especially when it comes to unmasking and recovery speed. Ferrous tones always had its down falls compared to conductive tones. Ferrous tones tend to drag small low conductors down into bottom left of the screen and into the ferrous zone. Conductive performs much better. The Etrac always ran better in conductive fully open or 1 bar along the bottom.

[@HistoryRevisiteduk]

Thanks for the tips Iain 👌🏻🧑‍🦯

[@nigelbrooks7506]

It's great that you are reviewing machines that are not currently In " fashion" I've recently been gifted a Marrs Gauss it looks a well made , light and Powerful machine from the Ukraine, the interface is difficult, I think it would make great project for a video Cheers Nigel

[@HistoryRevisiteduk]

I have been looking at the gauss, I do know people that have used and been very impressed with its depth 🥴

[@markjohnnojohnson5352]

Great video mate love how you go in-depth on all the machines👌🏻👏

[@HistoryRevisiteduk]

Cheers buddy

[@wilj71]

Well done Liam, im tempted to go and get myself another E-Trac now. 😁

[@HistoryRevisiteduk]

Can pick one up for a bargin nowadays

[@onlygazza]

I quite liked the etrac to use and it’s controls but eventually sold mine cos it was a bit suspect on a half gold sov I found

[@HistoryRevisiteduk]

Does seem that depending on what channel the etrac noise cancel is set on decides on what frequency’s the etrac favours , I will be showing this on a future test 👍🏻

[@MDCF1565]

Hunted with the Etrac for over 15 years in heavy iron, I ran wide open just blocking out the lower iron lines and top 2 for wrap around, Found 1000s of 1500s 1600s Spanish colonial artifacts with it in the iron. If that etrac says there's a non ferrous target there TRUST IT, I would pull out handfuls of nails and there was always a non ferrous target there if the Track told me there was.

[@HistoryRevisiteduk]

Great detector enjoyed using it , just a little slow for me so I’ve moved on to the manticore

[@MDCF1565]

@@HistoryRevisiteduk I swing the Legend, went head to head with Minelab Detextpert Sean with his new Manticore the Legend hit every target the core did with ease. Both have a little trouble in the flat iron but I prefer the Legend myself, looking forward to the new update. Cheers, Enjoying your channel From St Augustine Florida USA est 1565 the nation's oldest continually occupied city in the USA. Originally from Walsgrave UK 😊

[@HistoryRevisiteduk]

@@MDCF1565 I have the manti and legend and I’m finding in performance there isn’t much between them. Thanks for the support 🧑‍🦯🙏good fortune

[@vonborgestad]

On the ctx3030 I use combined Tone, I am not sure if you have the same options on the e-track?

[@HistoryRevisiteduk]

Can combine patterns but not tones on the etrac

[@tnsharpshooter8517]

Using 2 tone ferrous using Etrac is akin to fools gold. Preset ferrous line break for giving nonferrous tone is garbage. 4 tone ferrous better setup. And so is conducive tones with disc let down on screen somewhat. Some folks think because they find things using 2TF it is grand. They don’t know what they are missing using 2TF. Oh yeah they are missing stuff. No doubt. Cheers mate.

[@tnsharpshooter8517]

Tone break is set to 17 line ferrous. See page 66 of etrac Manual. 4TF tone break line much higher on screen (lower positioned).

[@HistoryRevisiteduk]

17 is very high on a 50 tdi scale, no tone breaks on this machine either

[@HistoryRevisiteduk]

Out with silver cherry picking discrim pattern later , video incoming