I hope my mistakes have been helpful for your 3d printing journey. Click here to watch me print a GW Battleforce Box: kzbin.info/www/bejne/hnSldKN6n8-abqM
@ThePattonboy12310 ай бұрын
I’m wanting to get back into printing, even though I haven’t had much run time other than 1 print that only printed 3 out of 4 wheels and then my fap broke because I used the spatula to get the print off I learned not to do that and then my lcd I thought went out so I replaced it and it did the same thing no picture so I put it in my storage but if it’s a software issue 🤦🏽♂️ with I hope it is something like that then I can start printing 1/24 car parts for my model kits
@jdc55582 ай бұрын
Firmware is not supporting to pendrive how to connect both together
@B4MBI72 Жыл бұрын
Thats good to hear someone else backup the theory of very slow or very fast lift speeds. 180-240 lift and 300 down for me. I have a half second delay before the UV comes on to give the resin a little time to settle back under the print. One tip I have is, after washing but before removing supports, soak them in very hot water, not boiling, but as hot as you can get away with and still put your hands in. Leave them for a min or so and it really helps loosen the supports which reduces the scaring when you take them off, half the time they will just fall off.
@Habes Жыл бұрын
Thanks for sharing and all your comments on different videos. I really appreciate the insights you've shared on all of them.
@FreedomForce100 Жыл бұрын
So if you have a curing station do you cure after the hot water?
@poggestfrog Жыл бұрын
@@FreedomForce100Usually it's wash > hot water > remove supports and then cure
@ChrisEpler Жыл бұрын
Tip: You don't have to put your resin back in the bottle every session. You can leave it in there for days, weeks. This way you won't be tempted to try cleaning your FEP and thus wearing it/scratching it. Also, paper towels are bad for cleaning the FEP, if you must clean it then get the resin out (large 250ml syringe) then soak up for rinse out the remaining with IPA and then gently clean the film with a clean microfiber cloth, NOT paper towels. Paper towels can leave it cloudy, just pushes the resin all over and you're left with a cloudy FEP. The microfibers are key to sucking up that cloudiness and leaving it clear!
@Habes Жыл бұрын
I need to invest in those microfiber cloths 👍
@Arterexius Жыл бұрын
Makes me wonder whether cotton cloth could do the same. I'm quite a lot into woodworking too and we use cotton cloth with our oils, as paper towels can leave unwanted scratches on a fine sanded surface. Cotton cloth for woodworking won't do that, have excellent suction ability and can be bought in rolls that are much cheaper than microfiber cloths
@JohnVanderbeck Жыл бұрын
Are you just tossing the cloths after?
@Arterexius Жыл бұрын
@@JohnVanderbeck Idk about this, but I imagine they could be washed for resin in IPA and then just left to dry, once the majority of the IPA have been squeezed out of the cloth
@YarHarFD Жыл бұрын
Some resins have to be stirred if they sit for more than few hours.
@jackschlaeger50242 жыл бұрын
I've been resin printing for a couple of years. You have offered good, relavent advice to beginners. I however, am still guilty of having too many STL suppliers. You CAN collect so many STL files that you can become paralyzed on what to print next.
@Habes2 жыл бұрын
Thanks for your comment! Yeah I'm starting to have that problem too, with too many STLs.
@cptkessler2 жыл бұрын
I agree. The library of shame has grown so much. I've noticed that I've become spoiled with pre-supported files and can't be bothered to do my own supports.
@DiavloPL2 жыл бұрын
Waaaaaaaaay too many STL's and patreons supported. I'm spending more money than I have spent on GW models earlier.
@The_Gryph2 жыл бұрын
@@DiavloPL Yep! Told my group that was it. Now more wild spending until I'd cleared my pile of shame. Then went and got a 3d printer and spend hundreds on STLs for other games systems! I could have bought an entire army with what I've spent this month alone :')
@DiavloPL2 жыл бұрын
@@The_Gryph and my 5th 3d printer just arrived, its not a best hobby for compulsive/impulsive :D
@tomyocom58862 жыл бұрын
Regarding failed prints. Depending on how complete they are and the Games you are playing, they can be casualties . Say an arm gets blown off or leg gets cut clean through with a sword. You finally get to use that blood red paint you have been saving. You get the idea. Melt a few as well everyone uses that dam fireball anyways!!!
@Habes2 жыл бұрын
That's actually quite clever. I've kept most of my fails that are at least 50% intact, so I'll look at making some objective markers and the like. Thanks Tom!
@tomyocom58862 жыл бұрын
@@Habes welcome and keep up the great work
@ashleyduckworthyt3224 Жыл бұрын
That’s BRILLIANT 😅❤ How did I not think of this
@deformiertergolfball4847 Жыл бұрын
yeah, im soon getting into printing and im not even scared of failiures cause i think they can get very decent terrain pieces or basing material. also if you are wargaming you are able to exchange your misprint with the decent print to show that it is down. imagine a full tanke beeing exchanged with a broken tank and then just get a LED candle with some cotton to make a smoke&burn effect.
@tomyocom5886 Жыл бұрын
@@deformiertergolfball4847 more than Awesome....that is great thinking!!
@LandoFabrizian Жыл бұрын
I'm about to take the step and purchase my printer. It's incredible how many people have such great advice across every line of model and through all experiences. Every video I watch and comment i read teaches me something I didn't know that I am better off knowing. So I thank the creators and the community. Much love guys❤
@Habes Жыл бұрын
Glad we can help. All the best with printing!
@lightningrocketcreates2 жыл бұрын
I went to check my resin settings and my lift speed was PERFECTLY in the middle of the dead zone, which explains why my prints suck. Thanks for the awesome tips! :D
@Habes2 жыл бұрын
No worries, glad I could help. All the best!
@dankehrig3419 Жыл бұрын
I been printing with the halot one for the last 3months and only had a hand full of fails and that’s only because of videos like this one!!! Plus the set up is super easy right out of the box!
@Habes Жыл бұрын
Thanks Dan! I'm glad you've found this helpful.
@Infernoblade10102 жыл бұрын
It's funny, I've had virtually all of these issues while learning resin printing! Great list and explanations!
@Habes2 жыл бұрын
Thanks for the encouragement John!
@falconiusazurius55722 жыл бұрын
One of the big lessons for me was that hollowing my prints decreased the wear and tear on my FEP.
@Habes2 жыл бұрын
That's a good point! I haven't printed too many hollow items yet, so thanks for the tip!
@garwmart Жыл бұрын
I've been thinking of getting 3d printer for a long time now. I saw some pretty good deals online, and that brought me to you channel. After pouring over loads of your videos, I pulled the trigger. I love 3d printing, and your videos have made it really easy to get into. Thank you, and keep up the great work.
@Habes Жыл бұрын
No worries Garrett. I'm glad they have been helpful. When it arrives, feel free to message me on instagram if you get stuck setting it up.
@garwmart Жыл бұрын
@@Habes PSH you made everything so simple. It's all set up and printing. I had 2 fails so far, but I'm printing in a basement. Did some small adjustments, and boom. Solid as a rock. Thank you again.
@Habes Жыл бұрын
@@garwmart glad it's working!
@GeorgMierau2 жыл бұрын
Thank you for your list! Made the Nr. 11 myself and would also add Nr. 15: leaving your IPA container open for many hours (even without direct sunlight it evaporates fast).
@Habes2 жыл бұрын
I'll have to remember that, I didn't realise it can evaporate like that. Thanks for the tip!
@samuelgreen1200 Жыл бұрын
I love Water-Washable resins and i swear by them. The cleanup process is less smelly, easier, and less likely to dry my skin or give me headaches
@Habes Жыл бұрын
Nice. Thanks for sharing Sam!
@CatalystPaints2 жыл бұрын
Awesome tips! Thanks for the video. I just started resin printing this week. Really enjoying it so far
@damo6662 жыл бұрын
My biggest tip for anyone is make sure you have enough holes in your prints so resin does not pool inside a print. A hole at the top and a hole at the bottom of the item is best for airflow and cleaning.
@Habes2 жыл бұрын
That's a great tip, particularly for hollow prints.
@christopherpardell44182 жыл бұрын
In particular, Run thru the model layers in the slicer and look for isolated chuck of resin shaped like a cup or bowl. These literally can from “suction cups” when the model is upside down and trying to pull up off the FEP, multiplying the suction force dramatically. So in a hollow model, there might be the cup shapes formed on the interior of the bottom wall, or even formed in the exterior of the upper surfaces. Drill a hole thru the lowest point in all of these to allow air and resin to flow readily so a suction cup isn’t formed. This goes for solid models too, any feature on the model that might form a suction cup against the FEP should have a hole drilled clear thru to the other side. This is especially important as models get larger as the suction forces multiply with area of the cup.
@321357w Жыл бұрын
I often add a hole at the lowest point of the print (for example, the head) not only to allow flow through when cleaning but to avoid resin accumulation when cleaning due to vacuum lock with the interconnecting passage being too small to allow sufficient cold resin to flow and drain when cleaning hollow prints.
@internalscreech Жыл бұрын
How do you then hide/fill in the hole in the print of the finished product? This makes a lot of sense, but I wouldn't want there to just be visible holes in my models
@poggestfrog Жыл бұрын
@@internalscreech If the miniature is large enough to warrant hollowing which is when you'd be hiding it then just print it in parts, usually the holes go in attachment points
@spruceg00se2 жыл бұрын
My biggest advice for those in colder climates is to make sure your resin is warm enough! You can buy a fermentation belt to help but cold resin is more viscous and increases print failures and decreases overall quality
@Habes2 жыл бұрын
Yeah, cold resin lead to a lot more failures for me.
@kilgoretrout54562 жыл бұрын
I second that. With viscous resin it’s super important, like Siraya tech blu. You can print a little heater enclosure and get the instructions from a Couple KZbin vids. It’s nice because it has a thermostat so you can set the exact temp you want your resin to be. It costs like $20/$25 total for all parts plus printer enclosure.
@scthomas1982 Жыл бұрын
When I started using a mini grow tent with a space heater in it my success rate increases exponentially. Definitely a worthwhile investment. Also makes getting rid of fumes easier
@keYserSOze2008 Жыл бұрын
I have a mars 2 and have had only a few failures, all of which were the result of the model orientation. My biggest tip would be to orientate your model with the majority of the mass (like the body) closest to the build plate, with the lightest parts (like the limbs) printing last.
@Habes Жыл бұрын
Yeah that’s a good one. Thanks for sharing 😁
@ZeroesToHeroes Жыл бұрын
As someone who is looking to get a resin printer bundle sometime this month, this is extremely helpful advice! Like Num.12, I would've never thought to wear gloves or a mask when using resin or curing, but now I know I'll have to keep some in supply
@Habes Жыл бұрын
Yeah safety is pretty important, particularly if you’re going to do it for a while.
@geekdiggy Жыл бұрын
i've been taking a serious look at resin printing over the past month or so as i will be getting back into scale modeling for the first time in 25 years. i've watched these helpful videos from many different youtubers, and based on all the information i've gotten, i can reasonably conclude at this time, resin 3D printing is just not for me. when i can free up more space at home and more time in my schedule, and get more serious about what i need to do with models (body kits, wheels, tires) then i'll give it a shot. but for now i think it's best i just look online for custom parts. thanks a bunch for the helpful tips. you saved me my own brand of nightmare. i hope to update a few years from now with good news of me finally getting into this.👍
@Habes Жыл бұрын
No worries, glad I could help. Looking forward to hearing back from you in the future if things change :)
@rizencomics91452 жыл бұрын
Good stuff. My Elegoo Mars 3 comes in tomorrow along with their wash and cure. Hope to avoid some mistakes after watching this
@Habes2 жыл бұрын
All the best printing. Glad I could help!
@MortdeathMinis Жыл бұрын
nice to see a fellow Halot one appreciator, I've had mine over a year, I must say I haven't bothered with dialling in the resins with the calibration tools etc. I just estimate given the resin parameters anbd its basically always been fine, for example my current product says 5-15 seconds and I just go at about 6.4 seconds and works fine. Also changing the location of your prints in the bed not only saves your FEP (cheap and easy to replace) but its also saving your LED screen (much harder to replace).
@Habes Жыл бұрын
I never thought about it saving the screen. Thanks mentioning that!
@PhilXavierSierraJones2 жыл бұрын
Nice video! I've had a print fail because I was printing too fast, and learned to dial the speed in correctly. The units matter a lot!
@Habes2 жыл бұрын
Thanks! Yeah getting the right speed makes a difference :)
@321357w Жыл бұрын
One other thing to mention is the recommended printing temperature by the Resin manufacturer per brand and or type of resin. Printing at a room temperature below the recommendation will result in higher resin viscosity resulting in failed prints due to the additional drag when the print lifts which can cause separation of part or all of the print as well as support contact points tearing away from the actual print object. Also, when you do a validation print like the cones of calibration, make a note of the room temperature as it only takes a few degrees Celsius lower than the minimum recommended temp to invalidate the calibration.
@Habes Жыл бұрын
Those are really good insights 😁
@321357w Жыл бұрын
@@Habes Thanks, trial and error with a bit of thinking about problems help solve a lot of issues.
@mr.delicious331110 ай бұрын
4years FDM and no resin printer but I’ve followed the tech and some of your advice is still useful for makers like me. like splitting up large prints into smaller pieces in case of failure you can reprint the pieces instead of wasting product. Appreciate the candid advice
@PawnSacrifices2 жыл бұрын
Also holes. If you’re doing a big print, you’ll naturally hollow it out. But without a hole the resin is being sucked up inside of the model each & every lift. (Think washing a cup & pulling an upside down cup above the water line with the water still inside) It creates a heap of unnecessary vacuum & will overload your supports mid print, leaving you with just a heap of ladders & the model in the vat. So tip. Using your slicer, Place a hole as soon as possible.
@GeorgMierau2 жыл бұрын
Could you share your curing routine for the hollow models?
@Habes2 жыл бұрын
It's not something I've done yet unfortunately even though I should. I would assume a UV torch pointed up one of your model's holes. I've seen one guy have a UV LED and he pushes it all the way up inside the models and moves it around to cure the inside. Sorry I can't be much more help.
@GeorgMierau2 жыл бұрын
@@Habes I've ordered an UV LED and will try this method as soon as it arrives.
@Habes2 жыл бұрын
@@GeorgMierau Hope it goes well :)
@manamedia Жыл бұрын
Thank you so much for producing this video. Helps a lot!
@Habes Жыл бұрын
Thanks! Glad I could help.
@mrj494 Жыл бұрын
suction force... make sure to add drain holes if your model allos it. ive just used ggreen stuff and/or resin to fill the hols and tada... but reduces suction cup issues
@Emtbtoday Жыл бұрын
I'm waiting for my anycubic 4k to arrive now so I think this os going to be one of the best channels to actually get help with it as a noob! Lol
@Habes Жыл бұрын
Thanks. Happy to help where I can!
@TheChariotdriver Жыл бұрын
Wonder why Anycubic doesn’t put a microswitch onto the platform for the wash and dry station to know when the wash station is installed. This would allow the circuit to not be placed in wash mode unless the tank is sitting on the platform which would prevent the high speed spinning mistake when trying to cure the model.
@Habes Жыл бұрын
Yeah that’d be super handy.
@Insan3_Script3r Жыл бұрын
Thanks it really helped me,since there is not so much info about the Halot One
@Habes Жыл бұрын
No worries, glad you found it helpful!
@Captain_Draco2 жыл бұрын
9:30 A mask won't do much for fumes, you just need better ventilation if this is an issue, the mask is just a safety blanket at that point.
@deformiertergolfball4847 Жыл бұрын
i mean it will still filter a little bit doesnt it ? like every bit of saftey is better then no saftey at all
@superslimanoniem4712 Жыл бұрын
Organic vapor cartridges should work.
@barneymiller40887 ай бұрын
You need to point out that each resin change means finding the right settings again. It may sound like fun changing resins each print, but this is a huge paint. Cleansing the vat takes time, but failed prints inevitably damage the FEP. Tuning the printer for a resin often ends with failed prints. Another one is printer cleaning. The resin is pretty nasty and light inevitability makes cleanup difficult. Also point out humidity Amd temperatures effect printing so working to keep these constant is a key to success.
@Habes7 ай бұрын
Very important point!
@ChessasWorld8 ай бұрын
I'm going to buy my first resin printer soon and I am really scared to be totally devistated thinking I'm too stupid for it because I would do things wrong I don't understand, but your video helped a lot :) Now I know what I should look out for! Sure there still will be things that will go wrong because of settings and such, but I know now what other things could happen and why. Made me a bit braver! Thank you very much ♥
@cavinrauch2 жыл бұрын
Funny you say you printed on the right side. Im currently struggling to get parts to stick on the left of my build plate. Also a Halot-One
@Habes2 жыл бұрын
Hopefully that's just a coincidence and not something wrong with the Halot One completely.
@cavinrauch2 жыл бұрын
@@Habes oh no 100% me the halot one has been amazing. Especially after the firmware updates lately. Super inspiring to see what you have printed with it so far
@troibandy21392 жыл бұрын
Nice video!!! I’m just getting into resin printing. Great suggestions. Honestly, the more I learn about resin 3d printing, the more I feel I don’t know. But, I’m trying as I’ve invested too much money to fail! In also have a Creality Halot Sky printer. I think my next print is the Congress of calibration AFTER I update firmware startings! Great tips!
@Habes2 жыл бұрын
All the best! Looking forward to hearing how you go!
@BloodSteyn Жыл бұрын
Thank you for this. I will be unboxing my Halot One and the UW01 Wash/Cure when I get home today and your video will be of great assistance on this journey. o7
@Habes Жыл бұрын
Glad I could help. All the best printing.
@dirkschoute33072 жыл бұрын
I had a lot of misprints like you. Models came loss from the supports and sticks to the FEP. My experience is that it's most of the time a problem with the supports. I use Lychee slicer and if you place supports at 0.00 mm into the object the issue increase. I always have my settings to 0.30 mm into the object. Lychee handles that setting different than ChiChubox dos. In Lychee the supports don't go in to the object for real. So an Island only sticks better on a support. My second collusion was slower lift speed and slower Retract speed. I set my lift speed to 1.8 mm/s and retract speed to 3 mm/s and lift the build platform 5 mm. I had more failures when this speed settings was higher (now I have non). The Lifthight can decrease/increase the print time in many minutes. 1 mm difference can save you 1 hour. Do not cure your botomlayers too long because the resin is too stuck on the FEP, and then you need a larger lifthight. Time settings...... just never change them again when you find the sweet spot. My opinion is that every Printer brand has his own setting. An Ellegoo printer can react different from an Anycubic and so on.
@Habes2 жыл бұрын
So true about different brand printers having their own settings. Always have to calibrate the printer individually.
@dirkschoute33072 жыл бұрын
Levelling the printer is also very important. Not just the built plate, but the printer too. This will give you less failures
@arcanterracrafts Жыл бұрын
Awesome video! I'm in the process of buying my first resin printer (have a FDM atm). This was just honest and quick tips. Much appreciated. You my friend get a sub!
@Habes Жыл бұрын
Thanks. I’m glad it was helpful!
@spencerbondy2043Ай бұрын
They now sell these magnetic baseplates for msla printers , using a 175x55mm on the mars ultra. Its smaller than original plate but you use two it like two sided tape applying the magnet and it has a thin plate for bending like ender printer down build plates. Which eliminated build plate scratches. Perfect prints. Easy cleaning. Around $20 CAD on the web. Only downside is you loose about 2mm in z axis build volume. Cheers hope this helps .
@Ricanthunda Жыл бұрын
I have the exact same printer and was wondering what your exposure setting were for the elegoo water washable resin. I just switched to this resin and have only gotten failed prints so far.
@Habes Жыл бұрын
I ended up using 3.5s iirc. There's a video of me review that resin with the Halot One. kzbin.info/www/bejne/jGqvo614gcR1epI
@Hartwig870 Жыл бұрын
Just use the user settings on Lychee to get a good ballpark. My cones printed perfect the first time with various resin types.
@Habes Жыл бұрын
Yeah those user settings are pretty useful
@erikstrawn38856 ай бұрын
When I'm working on my cars, my rule is to never put a bolt in place unless I'm going to tighten it. Use the same rule for your build plate and you won't ever leave it loose.
@ilan2592 жыл бұрын
Hello, can you go a little more in-depth when it comes to the dead zone? To me it sounds like you should not be printing within the 80-150mm lift speeds but I think youre implying the opposite of that? I'm new to this so I'm just trying to understand this better.
@Habes2 жыл бұрын
Sorry if it wasn't clear. Either print at 0.8mm/s (48mm/min) or slower, or print at 3mm/s (180mm/min) or faster so you're outside the dead zone of 50-180mm/min. I opt for printing at 3mm/s just because I don't like waiting so long, but I have to add some extra supports because of the extra strain it puts on the supports.
@DataAllister2 жыл бұрын
@@Habes And in regards to the increase in lifting speed to 180mm/min. That also risk damages to FEP that was stated earlier, correct?
@Habes2 жыл бұрын
@@DataAllister yeah there can be a bit more risk to damaging the FEP at faster lifting speeds. For me I've chosen that faster lift speed and will just deal with the risk that my FEP might not last as long in favour of faster printing times. That could change further down the track, but for now that's what I'm trying.
@accentplaya182 ай бұрын
One of my biggest fails was when I first bought my Mars 2 Pro. I spent 2 days changing printer settings before eventually realizing I never removed the plastic from the FEP film. Second biggest fail would be the number of times I've forgoten to even put the build plate back on when cranking out back to back to back prints. #8 Was hilariously applicable to me. I very much fall into the camp of having "files of shame". There's just so many models, toys, and tools that I'd LOVE to bring to life!
@faolheamh8422 Жыл бұрын
Funny you should say about tightening the build plate I always remember that, but have twice now forgotten to screw the vat down - first when I got the printer, second after cleaning it (had the printer about a week) So I've stuck a post-it on the machine to remind me
@robsonribeiro75522 жыл бұрын
Thanks dude! Your videos is helping a lot, just got my printer set up this week, let see how it goes =). CheerS!
@Habes2 жыл бұрын
Glad I could help. Happy Hobbying :)
@hauntswargaming2 жыл бұрын
Great tips! Definitely try different resins. The cheaper resins are cheap for a reason :)
@rcane68422 жыл бұрын
I want to jump into resin printing as a hobby. I'm a bit familiar with the traditional resin mold. My question is, is the resin being used in SLA printers the same as that of the traditional resin crafts? Can you also put alcohol inks to make random colors?
@hauntswargaming2 жыл бұрын
@@rcane6842 no, sla printer resin is activated by uv light. You can dye it. Idk what kind of dye to use though.
@bjohns3961 Жыл бұрын
I got an elegoo with elegoo resin and it basically worked right out of the box. I even forgot to tighten the build plate and it printed perfectly
@Habes Жыл бұрын
Yeah I found that with my Saturn 2 as well. I think the newer printers are becoming more plug and play.
@erfquake111 ай бұрын
Oh man, this is really helpful, thanks so much. A great idea for a video would be more examples of failed prints, specifically what was wrong, and what the solution was/were. eg: I'm getting this weird edge-lifting of flat-bottomed objects, making them look more like cartoon boat hulls. I think it might be a loose or sticky FEP, or plate crowding, or wrong initial exposure time duration, or not big enough skirt, or gypsy curse or something else, but there are frankly too many variables and not enough time available on the local library's "village bicycle" resin printer. So itemizing specific problems as a compilationin video would be gold to me. Thanks!
@Habes10 ай бұрын
Sorry for the late reply. I did record a video of “common issues and how to fix” but found it wasn’t up to scratch for a video. After hearing this I think it’s worth me revisiting that idea. Thanks!
@glodigit2 жыл бұрын
I'm designing a resin printer (have only used FDM) so this was insightful.
@Habes2 жыл бұрын
Glad you found this helpful!
@blueckaym Жыл бұрын
I printed almost all of my first bottle (Phrozen Aqua Resin Ivory 4K, which I understand is actually good resin, but I picked just for the color), on a Mars 3 Ultra (not Pro). Also I don't have washing and curing machines, I just use a plastic box of alcohol and cure them in the Sun (of which lately there's very little - mostly clouds and rains). And so far I have zero fails! I'm quite surprised too. I've watched many videos on resin 3d printing and saw how many things can go wrong. Also when I started I did no settings in the slicer (chitubox). I opened the settings windows saw that I have no idea what I'm looking at and only set the printer to be my model in the slicer. The only issues I had so far is getting out the printed parts out of the build plate. Especially those I print flat, which I do for the miniatures base plates - being low profile and flat bottom seems waste (of resin and most of all - Time!) to angle them and support them, so I just put as many as I can for single print, and in 20~30 mins they're done. But yes the flat base plates are the hardest to remove from the build plate (but also the strongest so I don't shy of using extra force). And the other issues are that I broke 3 pieces when removing the supports (after I've removed them from the build plate). Fortunately 2 of the 3 breaks were clean and was very easy to superglue (the 3rd one was also clean, but I didn't notice it when removing the supports and I guess I've thrown the front of a female figurine foot in the trash). So as a result I got cocky and I printed a bracket to hold the build plate at an angle after printing to better drain the resin left on the build plate before washing it. I got that pre-supported (and clean stl of course) and I was going to print the supported version as usual, but I noticed some supports looking weird and unnecessary (and too thick), I played few minutes trying to fix just the weird ones, but I gave up, started with the clean STL, set supports to light (and even made them a bit lighter, down to 0.7mm thickness), printed it expecting epic fail and that I would have to finally drain the resin in the tub thru a filter to remove the failed parts (and avoid breaking my screen afterwards) ... I even hollowed the bracket and put few small drain holes because it seemed to me it has good potential to save on resin, while still being acceptably strong ... But I got a problem - it printed perfectly fine! Build plate removal and supports removal was much easier. Wasn't sure if the resin from inside the bracket was drained already, so after cleaning it and curing it a bit more in the sun I dared put my lips on one of the holes to blow in and see if any resin will get out, but nothing got out except for some air. So now I still have no idea what to do if something goes wrong :/ I'm going to buy a flex-plate to make prints removal much easier, and perhaps I'll get simple curing box (or put one myself - DIY style), and next I'll have to use the regular resins, so I wonder if there'll be any difference.
@Habes Жыл бұрын
Thanks for sharing. Sometimes it's easier to reprint that try save the print, depending on what print is. All the best with the printing.
@blueckaym Жыл бұрын
@@Habes , Thanks! You too!
@edeaglehouse2221 Жыл бұрын
Don't risk getting uncured resin on you. Use a straw, air compressor, or vacuum to test for leftover liquid resin. The chemicals in resins are no joke. Be safe.
@blueckaym Жыл бұрын
@@edeaglehouse2221 , I know. Thank you for the reminder! I'm being intentionally very careful (in addition to the mask, gloves & glasses), doing everything slower than I would normally do, and so far I don't have a single spill. I'm also waiting now for the wham bam flex-plate magnet to stick to my build plate (72 hours), and in the mean time I'm making a DIY UV-curing box from a cardboard box Alu-foil and uv-led-strips. Even got couple of those tiny turntables for jewelry (found them for about 5€ a piece. Actually I found them even cheaper, but I had to order 100 :) which of course I didn't) Btw I played with hollowing and made an extreme print - a ~30mm human fighter mini hollowed to a 0.5mm wall, and added plenty of holes in hard to see places (some smaller holes armpits and under-side of the cape to allow for air to enter/escape and push the resin thru the bigger holes on the feet, arms and also one where we all have a hole :)) I'm saying this because I wondered how the easiest to get liquid resin from inside the model, and thought about blowing thru, but then I read that this is excellent way to get droplets of liquid resin flying all around (if there are such inside the model in the first place). So I'm focusing on rinsing it really well in IPA to get it in & out many times and wash any leftover liquid resin there. Bubbles are a good indicator that air & IPA are moving thru with each dip. It works well when the cavities and at least 2 holes are big enough. The challenge is with tight cavities in a model, given that also in those places often it's difficult or impossible to add a large hole. But here Lychee slicer actually helps. It allows me to block areas of the model hollowing to avoid such tight spaces and focus only on a larger cavity that's much easier to manage and clean. What I though about for curing the resin inside tighter cavities is perhaps I could get few optical fibers, tie them together on one end, and place them directly again a UV led (probably some bracket could be useful), and then insert the free ends in the holes of a hollowed model to cure it better from the inside.
@mrjinglesdice2368 Жыл бұрын
generalizing a bit here. much more to consider when calibrating exposure time like environment etc.
@Habes Жыл бұрын
When I made this video, temperature wasn't an issue for me, so I never even thought about its affects on calibration.
@nicholasvinkler16355 ай бұрын
Love it. Made sure not to mess up that one. Earned my sub
@Habes4 ай бұрын
Legend!
@strilteras23212 жыл бұрын
The hardest thing for me to for e myself to do is the ppe primarily the respirator but also not cross contaminating tools. Have a procedure and stick to it for cleaning the machine and your tools.
@Habes2 жыл бұрын
Yeah I struggle not to touch anything once I get resin on the gloves when handling prints. No matter what I do, resin just finds a way to get everywhere.
@ScootLogix2 жыл бұрын
5 failed prints so far. Did a lot of research too prior to purchase. Was getting pissed, lol, did research into fixes and making some progress. Alas I come here and your cones of calibration seems like what I might need. We have same resin printer. Thanks, almost gave up hope lol.
@Habes2 жыл бұрын
Thanks, my first week was pretty rough XD Good luck, can message me on insta or discord if you need help. Both in channel bio.
@Chimer24-qs5wo7 ай бұрын
I'm considering starting 3D printing and this video's a big help. Forewarned and all that. Thank you. Subscribed )O(
@Habes7 ай бұрын
Thanks. All the best with the journey!
@danieltomczyk70058 ай бұрын
I am just starting with resin printing for miniatures for my tabletop games. I am using the water washable resing at the moment but I'm having trouble with the removal of my print off my print bed. after taking the printout and into the wash, when I tried to scarp my print off: 1. my scarper had a very difficult time just getting between the print and the bed AND 2. When I tried to scape/lift it off the bed, the print cracks/brakes. Any tips and or tricks?
@andrewwelsh91928 ай бұрын
some great tips, don't forget resin temperature, that was causing all sorts of problems until i realized it was a factor in fails.
@EricPaul0072 жыл бұрын
Great video, great tips. Recognized your not fastening the build plate, had a similar moment of shame: forgot to fasten my vat, also a recipe for disaster.
@Habes2 жыл бұрын
Thanks. I'm glad the video was helpful. I always have to triple check the build plate, sometimes even as it's lowering into the vat as I start a print.
@pkmcleod Жыл бұрын
Recently started, and it's going great so far! Just struggling to figure out which resin to buy... and which ones in Australia won't break the bank! Any tips/hints?
@Habes Жыл бұрын
Hey Peter, I’ve been using Elegoo Abs Like for minis. Usually buying off eBay when there’s a deal. Best to buy in bulk when there’s deals if you can manage. However I haven’t seen any recently.
@pkmcleod Жыл бұрын
@@Habes Thanks for the quick reply! That's the stuff I got with the printer... but it's $60/1,000 on Amazon, so I'm on the hunt for something a bit more affordable...
@Habes Жыл бұрын
@@pkmcleod yeah, I think if you can get $40/1kg that's a good deal. I got around that but had to buy 4.
@shabadooshabadoo4918 Жыл бұрын
i bought a anycubic i3 mega x a few years back and its never printed correctly lol. I think its PCB overheats or something im not really sure. I've switched the sd card and replugged all the cables and done like almost everything possible. But after like 2-8 hours of printing it just freezes. So im pretty confident its not my user error at this point but for a long long time i was pulling my hair out trying to figure out what was wrong because it was my first 3d printer and i assumed it was user error the whole time. Its nice to see that resin printers can have failures too cuz I was considering abandoning fdm for ease of use and picking up resin.
@Habes Жыл бұрын
Yeah. The newer machines are getting more plug and play though. Saturn 2 I had hardly any issues.
@shabadooshabadoo4918 Жыл бұрын
@@Habes Hi habes, a quick update. I finally got the damn thing working I think. its been printing 24h with no stops. The anycubic i3 mega x apparently only comes with a 1 inch fan on the pcb and no exhaust fans. I added an exhaust and an intake and it seems to have fixed it. If you hear anyone else complaining about a similar printer or issue then you know whats going on.
@funx24X72 жыл бұрын
My first print failed from not enough resin in the vat (or perhaps too ambitious a print). I'm surprised there aren't level indicators on the side of the vat for this reason, at least there aren't on the one in my anycubic.
@Habes2 жыл бұрын
Yeah, I think some companies have started adding markers to their vats, but it's weird that they didn't have them from the start.
@keeganpenney1692 жыл бұрын
One very important thing you forgot. Ambiant room temperatures. In warmer parts of the world less of a problem, if you live in colder regions your gonna want to get that room temp up to between 20 and 30C as the warmer it is, the more viscous your resin is, less print failure. Also depends what your printing but generally speaking you cant expect great results if your printing in a cold room.
@Habes2 жыл бұрын
Yeah that's definitely true. When I made this video I had only been printing for a few months and we were slowly heading into winter, so I hadn't experience what happens once it gets colder. Definitely solid advice. Thanks Keegan!
@countrydude1832 жыл бұрын
Would something like a fermentation belt or another source of heat also do the job instead of raising the overall room temperature
@Habes2 жыл бұрын
@@countrydude183 Yeah, particularly from and energy/cost point of view. I current have a small 40W heater that I use with my printer in a small cupboard when it gets cold. Haven't tried a fermentation belt though.
@countrydude1832 жыл бұрын
@@Habes I was thinking that would be an alternative but just wanted to confirm, thank you very much.
@geroschorch13652 жыл бұрын
*LESS viscous
@HarryBHouchinsАй бұрын
Some interesting help here. I've been remarkably UN-successful! Do you have a "special" room set up for printing? I use my garage in the summer when temperatures are around 70+ degrees F.
@HabesАй бұрын
I do print in my garage too. I think hotter is better than colder. In winter I heat up the resin before printing.
@DavidFernandez-sc5ws2 жыл бұрын
I’m just getting into res printing. What’s a good time to wash/cure models? Like how long should I wash/cure a small model vs a bigger model?
@Habes2 жыл бұрын
I don’t know the exact “science” of it. For washing I use a wash and cure station and put them in for about 4-6 mins depending on how many prints are in there and the size. I think you can’t “over” wash the prints, but I’ve heard of prints being ruined when people have forgotten to take it out of the IPA for a few days. For curing I put it in the cure station for around 4 ish minutes. It’s on a spinning plate. I know some people cure it for shorter times, because if you over cure it, the resin may become brittle. However the aim is for the print to not be tacky/sticky on touch and that usually takes 4 minutes in my set up. Bigger models might take longer as they might have to be rotated to get all parts cure.
@Dark0Adonis2 жыл бұрын
My on going issue is the bumps left after removing the supports.
@Habes2 жыл бұрын
I haven’t had too much trouble, but sand paper or a nail file might do the trick. For bigger supports it could be worth using some clipper like you would for removing plastic models from sprues. I hope that helps Jonathan!
@jakeplaysgames28202 жыл бұрын
I have the exact same printer as you and literally got it yesterday. I must say your video helped me out so much but as this is my first printer I'd love more tips and so on.
@Habes2 жыл бұрын
Thanks for the comment. I'm hoping to do a review on the printer as I've had it for 7 months now. Is there anything specific you're interested in?
@jakeplaysgames28202 жыл бұрын
@@Habes it's hard to say exactly considering this is my first printer and I've barely ever sratched the surface but I would like to to kniw what washing and curing station you're using.
@Habes2 жыл бұрын
@@jakeplaysgames2820 I'm using Anycubic Wash and Cure 2.0 but the Halot One's build plate is a bit too big. It fits inside fine, but if you have a full build plate it won't fit.
@jakeplaysgames28202 жыл бұрын
@@Habes Gotcha I'll keep that in mind before I order my curing station.
@johnwillenbruch3958 Жыл бұрын
Any advice on making it as close to plug and play as possible? I want to 3D print to get cool minis not as a hobby in itself. Do you have a video on that?
@Habes Жыл бұрын
Newer machines. I bought an Elegoo Saturn 2 and I could easily print stuff with the default resin profile for their ABS like resin. There will still be some tinkering around as fails will happen a lot of the default settings with more recent printers will get you like 95% of the way there. All the best with it!
@TheZahnputz Жыл бұрын
good advice, especially since youre only printing since 3 Months but i cant agree with you about "overloading" the buildplate. Its different with large parts with big cross sections, but with miniatures which are pretty similar concerning the print area (=not problematic), you can fill the plate to the last gap - even with a 13'' printer like the Anycubic M3 Max, given that you adjust the lift speeds
@Habes Жыл бұрын
Good point! It’s one of the things I’d change in this video looking back. I squeeze my build plate to the max now.
@ashen938119 күн бұрын
Is an enclosure/air purifier required for resin printing? Would a desk fan and open window help with removing the VOP fumes that are released during the print?
@Habes14 күн бұрын
I'm not sure about air purifiers. An enclosure is only good if you have a way to vent the fumes out. Otherwise when you open it, all the fumes are there. I can't confirm if a fan and open window would be enough for a health perspective. But for me I would have the printer in a dedicated space that I don't go in often, with a lot of airflow. I hope that helps.
@Jediand2 жыл бұрын
Hey; great video but can I ask a couple of questions? I've been struggling with my 3D prints and would love your help. Should I remove the supports before curing or after? I use a water washable resin atm as I don't have a washing and curing station. Also I seem to be losing a lot of definition on the smaller models, could this be due to over exposure while printing? Can you over cure an item? And would you recomend any 3D programs to help do things like divide a model? Thanks and have a great day!
@Habes2 жыл бұрын
I'll try my best to answer. I always remove supports before curing. I found that to be easier, and sometimes you can use warm water to help in that. It could be over exposure, maybe it could be worth lowering your exposure and doing the same model and compare them. I'm not too experienced with post curing process. I usually cure it until the print isn't tacky/sticky anymore. That is usually a couple of minutes in the wash n cure. I think you can over cure prints but I'm not sure what happens, I think they become a bit more brittle 🤷♂ I've have used prusaslicer to cut models but it's pretty bad. Only does a straight line. If you want a more detailed program maybe Blender? But it's a bit of a learning curve (I can't use it 🤣). I hope that helps, happy hobbying :)
@Jediand2 жыл бұрын
@@Habes Thank you so much with the reply! Take care and happy printing!
@edeaglehouse2221 Жыл бұрын
Best advice I've seen is to clip supports after washing but before final curing. Then, the print is a little softer and removal doesn't leave as much scarring.
@EctoBeats Жыл бұрын
You know, I laughed at you when you talked about securing the build plate. Got my 3d printer, must have done it 2-3 times now. Thanks for all the tips!!
@Habes Жыл бұрын
Yeah I almost need to put a sign up reminding me 😅 Glad the video helped
@nfldend501 Жыл бұрын
Can u help me? They are only about 22mm high but one leg on 5 seperate figures didnt print then i printed two one total failure second is missing a leg again
@Habes Жыл бұрын
There could be a lot of reasons. I suggest joining a 3d printing Facebook group or discord and post your settings and picture of the slicer. I hope that helps
@aaronjones4397 Жыл бұрын
this is a great video for beginners, something I'd like to add, is do not wash resin down the sink. Its bad for the environment
@Habes Жыл бұрын
Yeah that’s a great point that people easily overlook.
@No1sonuk3 ай бұрын
My favourite so far (after a week) is forgetting to secure the VAT! Came back to the printer after a half-hour print to find the build plate lifted to the"finished" position, with the vat still attached to the plate! 🤪
@disturbedfan5452 жыл бұрын
Honestly getting a good slicer program made it much better for me. I use to use like anycubics slicer but just got failure after failure. Then I switched to Lychee and bam, success
@Habes2 жыл бұрын
That’s a good point. I personally haven’t experience that as the first slicer I used was lychee but I’ve seen people have slicer issues which can be frustrating if you don’t know it’s the slicer causing the issue.
@joshbedo8291 Жыл бұрын
What are you using for paints? Also what are you using for curing?
@Habes Жыл бұрын
Stand acrylic paints for miniatures. Vallejo, army painter, citadel. I’m using anycubic wash and cure 2.0
@joshbedo8291 Жыл бұрын
@@Habes thanks for the help!
@jordonr1002 жыл бұрын
I once forgot to bolt down my vat and came back an hour later to the build plate lifting the vat full of resin up and down
@Habes2 жыл бұрын
Oh no! Hopefully it didn't make too much of a mess.
@dakr3464 Жыл бұрын
Im learnin today ! 😅 yesterday i started a 19 hour beserker print file on my halot 8k and first 2 trys it diddnt stick to the bed so now im on number 3 and its stuck but now im worried imma run outa clear blue ink in the trey. i started with 500 now its lookin light and i gotta go to bed so im thinking about adding clear red to make a half blue half purple print incase it runs out.😅 uhh hopefully the blue dont run out
@Habes Жыл бұрын
If they have the same exposure settings you should be good. All the best!
@karlh66922 жыл бұрын
At the 2.55 minute mark on your video you show an empty vat but in the sections that show the screen there is static cling or moisture attraction happening on the screen. It looks like bubbles but it is major cause of print fails. Try cleaning the screen and underside of the vat with alcohol and pre warm the resin so during the peel process the suction is not pulling moisture out of the air and attracting it to the cold vat.
@Habes2 жыл бұрын
Thanks for the tip Karl!
@Павел-в9е2уАй бұрын
Good afternoon. Can you tell me why when you click on the model to print , on the printer,Creality ld 002r, the error is displayed: The cutout does not correspond to the projected -1440 resolution?
@Ultimaniacx42 жыл бұрын
8:44 I've had my printer for a couple months now. I still make this mistake every once in a while.
@Habes2 жыл бұрын
Same here, I'm super paranoid now, even as the build plate lowers down, I'm checking if it's fasten.
@kennyg21ful Жыл бұрын
my mars 3 pro prints fine with normal resin but as soon as i switched over to water washable resin, failures every time
@pekwalker Жыл бұрын
Don't fear failure. Every failure can be a learning experience and a bridge to something better down the road.
@Habes Жыл бұрын
That's great advice. We can learn from everything!
@edh326810 ай бұрын
Thank you for this very informative and concise video! Do you have a recommended slicer software you prefer? I know that can play a big part in 3D printing.
@Habes10 ай бұрын
I use lychee. I don't have too much experience with Chitubox or other slicers. I think a lot of it is personal preference.
@yuyu632 ай бұрын
I almost exclusively use water washable resin for the last 3 years, here is what i have for anyone who thinks they want it. The details are better than other resin's, it flows smoother and doesn't separate so i have left resin in my printer for months and just started a print up one day and came out fine, use a raft the parts are brittle till cured and if over cured, it doesn't have much of a smell and i can use it in a room im in with just a box fan keeping air moving. Happy printing
@johnnobravo19782 жыл бұрын
Hi there from Australia, just wondering if a Anycubic Photon M3 Max would be any good ? Looking at starting out thinking resin might be better due to detail as I want to print Figurines , cars , and buildings and maybe movie character helmets. Just so so scared to lay out so much money and never done this before and wondering what to print to make money on
@Habes2 жыл бұрын
I have briefly looked at that printer as I'm looking for an upgrade. It looks like a good model. Just remember it's going to take a while to learn, and things won't always work out so easily. If making money is what you want to do, I'd suggest starting it as a hobby, see if you like it and then start small. You could buy a printer and start and find out you hate it. Maker's muse as a video on "printing on demand" and making money 3d printing so that could be worth checking out.
@johnnobravo19782 жыл бұрын
@@Habes yeah sweet. Definitely more going to be a hobby at first as I love figurines, model cars , model planes , movie props, famous buildings around the world , certain movie characters and creatures etc. I know resin is more detailed and FDM is more durable and easier and cheaper. So I'm stuck between Anycubic Photon M3 Max for $1600AUD or Anycubic Kobra Max for $800AUD or should I get both lol. Also seen a 3D printer scanner at Jaycar Australia for $799 but not really a big scanning area. I can just see it all adding up especially with materials and paints and tools resin and fdm and the Alchohol for wash n cure. I just know I get into things and lose interest quickly and it gets expensive with that. Then again I don't want to spend 2 weeks making something and end up selling it for $20 Been trying to search up so many ideas and things to print and another thing is I guess sure it would be cool to print then paint something but then I'd leave it on a shelf and get over it lol.
@Habes2 жыл бұрын
@@johnnobravo1978 I got no idea about FDM printers. I'd pick one type of printer (FDM or Resin) and learn that. All the best with it!
@wminster2 жыл бұрын
The only STLs I’ve purchased are a guy who had a one time purchase on his etsy where he continuously updates a mega folder that contains all the STLs he makes, and it was like 70% off
@Habes2 жыл бұрын
That sounds like an awesome deal!
@samualwilliamson11872 жыл бұрын
If you have a filament (pla) printer you must check the printing at least every 1/2 hour. A catastrophe is just one blob away.
@Habes2 жыл бұрын
Yeah that's happen to me before XD
@JohnVanderbeck Жыл бұрын
Links to Tableflip and Atlas would have been helpful
@Habes Жыл бұрын
Soz, was a typo in the description, wrote Tabletop instead of Tableflip. Also added Atlas now. Thanks for the comment!
@nosalis2 жыл бұрын
the exposure calibration is per resin type ? or do you need to do it every time you get a new resin bottle ? ( even if it's the same you have been using before) I haven't bought 3d printer yet but I'm almost on the edge of buying it, so I'm looking at all kinds of the videos I have seen this one a lot > exposure calibration this model looks great !
@Habes2 жыл бұрын
It's per resin type. So if you have ABS Like and then swap to Water Washable, you'd want to do an exposure calibration. It's even worth doing if you swap brands, as there could be a little variance. I hope that helps.
@nosalis2 жыл бұрын
@@Habes ah perfect, yep that's what I though, that's for confirming. Really hope to embark on the 3d printing yourney, it's been something I have been thinking about for few years now
@Habes2 жыл бұрын
@@nosalis No worries. All the best and glad I could help.
@edeaglehouse2221 Жыл бұрын
Exposure depends on the resin and the printers light source. The manufacturer and printing communities can likely suggest settings for your combination of choices. Somebody it there has probably already tried them. There are many folks happy to help.
@RetiredToddler Жыл бұрын
Hello, I'm a beginner with a HALOT-ONE and I'd love some advice if you're willing. I've just got a new bottole of Phrozen 8k gray resin and my prints are not sticking to the build plate at all. When I drain the tray, I see the first few base layers of the print stuck to the FEP. Do you have an idea of what might be causing this? My most recent bottom exposure layer was 5, base layer exposure time 35s, exposure time 2.5s. I have learned recently exactly what's happening in this printing process (thanks to you and other YTers!) and now I'm wondering if my FEP needs to be replaced.
@Habes Жыл бұрын
I’d relevel the build plate. Most times when things aren’t sticking to the build plate that’s the reason. Have a look at the FEP. If it’s super cloudy and scratched replace it, but otherwise it should be ok.
@heleneholz53002 жыл бұрын
hELLO! Thank you for sharing this video. I'm really curious about the Lift Speed Deadzone thingy. Do you know where I can read more about it?
@Habes2 жыл бұрын
Thanks. I had a quick look and couldn't find anything specifically relating to it. It came up when I was talking to some tech support from Atlas when I was having trouble at the start printing some One Page Rules minis. If I find anything later on I'll let you know. If I can find the information, I'd really love to do a video going deep into the math/physics behind print failures.
@heleneholz53002 жыл бұрын
@@Habes thank you so much for the leads! i will take a look at Atlas :)
@Definitely.not_0li Жыл бұрын
Would you say buying a wash/cure machine is worth it?
@Habes Жыл бұрын
It's kind of personal preference. Lot's of people will say you can make sure own washing station with a bucket, then a box with foil and a UV lamp. For me I'd rather spend the $$$ same a bit of time and hassle. I've got the anycubic wash and cure 2.0, and have found it worth while.
@mrsnufflekins2 жыл бұрын
I have a question, everyone recommends a respirator but noone says what kind to get. What kind would you roccomend? Are there certain specs to look for?
@Habes2 жыл бұрын
Hey, I'm really sorry I don't know the specifics of what is REQUIRED. This is the one I use, and it's to Australian and New Zealand standards so it could be different in your country. "The Trojan A1+P2 Replacement Respirator Cartridges + Pads provide A1 Vapour Protection and P2 Particle Protection as per Australian Standard AS/NZS 1716:2012."
@navyrobot47782 жыл бұрын
Hi! As soon as my resin printer arrives I’ll be diving into the world of resin printing, though safety is a concern. Do you think having the printer in a desk on my bedroom safe? I planned to open my windows and go somewhere else while printing to avoid fumes. But I’m no expert :P so what can you suggest me?
@Habes2 жыл бұрын
I've seen online that people do it. That doesn't mean it's safe. I personally wouldn't have it in the same room, particularly a place where you sleep. If you can find another place in your home that would be better. One friend has his in the laundry with an air purifier.
@bbg-designs83642 жыл бұрын
If I were to program a little jiggle when the print is lifted out of the resin so that the resin could be jiggled out, would that effect the print?
@Habes2 жыл бұрын
If this is in between layers, I don't think it would be necessary. If it's at the end of the print to shake of excess resin, I think it would be ok as long as it's not too strong. Some printers allow for rotating the build plate, and the excess can drip back into the vat.
@thesasquatchgamer97133 ай бұрын
Whats that model at the start of the video that looks like a samuari in power armor?
@RazDesignAB2 жыл бұрын
Hi! Regarding the ending, I have been working on a solution that make the safety of resin printing a lot better. Would that perhaps be something you be interested to talk about? Best regards//Rasmus
@Habes2 жыл бұрын
I saw your kickstarter, looks very interesting.
@Mdbunn20132 жыл бұрын
wahoo, just click you over till 500 likes. nice video man. feel like I've missed out on 5 minutes of unboxing.