Mistakes When Trimming Your Truck To Fit Bigger Wheels And Tires

[@CustomOffsetsTV]

Shop for anything you need when it comes to your build at Customoffsets.com!

[@BravoakaMrAlabama]

Pulled a muscle running to this channel.... Great information, can't wait to throw these 26x14-81 Lincoln 37x13.50 on my Tahoe...

[@CustomOffsetsTV]

Way to go!

[@nemesis851_]

Banker speaks the TRUTH !!

[@tysentheking]

I really really love you guys. I’m doing an 01 Suburban overlander. I’ve learned so much from you. I watch all your videos.

[@MrTylerg506]

That undercoating you talked about should be an oily/waxy type undercoating like Woolwax, Blaster Surface Shield, Fluid Film….etc because that rubberized stuff will trap moisture and what not underneath and rust it even worst.

[@Pescador2022]

Thank you for the informative video. I had one question please I wanna make sure I understand when you’re talking about 9 wide you’re talking about the tire rim for example, 20 x 9 rim. Not the tire. Thanks 👍

[@GrampsforSix]

any recommendations on a minimum clearance between the tire and Upper control arm? I'm running 12.8 wide on a 1500 - 2" lift 1/4" spacer and only have about 1/4 clearance to the control arm... I'm going to a 3/8" spacer, but don't want to make the rub worse by going wider on the spacers.

[@capt.crunch1276]

About to trim the crash bars this weekend.

[@RicardoCerveraBlanco]

Hi man, thanks for the video, I am increasing my wheels for a couple of inches and your advise on the front wheels is great... Regarding the rear wheels. If the new size fits, do I leave it or should do some trimming anyway?, I am lifting it anyway to compensate for those 2 extra inches. Thanks.

[@KROCK062]

I appreciate you ! 😂

[@JB-nf8nk]

More power to ya if you just grab that sawzall, put in the 10" blade and give 'er the onion! Let 'er rip tater chip🤘I think sawzalls are awful... I've used them for 25 years and have several and I hate them every time I use them. They always seem like the perfect tool, then they're not... People love them, but even the sawzall lovers have hated having to use them. I'll always try an air cut-off or air recip or reach for the angle grinder, hell, I'll even grab the multi-tool before I try the sawzall.

[@trin_sierra]

FYI, you can use a Dremel to do a NorCal. It just takes a little bit

[@chrischurlymccormick6681]

Oh ya nor-cal baby 👌

[@blakebox1481]

Made 22x14 -90 and 355/40 nitto trail graps with with no rub on my 14 Silverado 1500 stock height. Truck is in the gallery too. Blake.Box

[@AndrewChildress]

Do you guys sell spiked lug nuts for motiv wheels?

[@CustomOffsetsTV]

We got spiked lugs right here www.customwheeloffset.com/store/wheel-accessories

[@AndrewChildress]

@@CustomOffsetsTV you guys are great

[@red_gt_5.025]

I got a 2016 stock height ford f150 lariat 4x4 if I get 20x10 -18 offset do I need to level ? I have 305 55 20 tires

[@amacklifts]

100%

[@SilveradoJoe]

🔥

[@Yaboi4Life]

Yoyo

[@Pure_KodiakWILD_Power]

These damn tubi commercials 🤦‍♂️

[@jeremypeck5781]

My titan xd was the worse!

[@A_Chevrolet]

Day 10 of asking for a “so you want an OBS Chevy” video!