Mitsubishi Ductless Mini Split Installation | Central Florida & Orlando HVAC Contractor

[@tuffram2165]

Finally Finally a Mitsubishi mini split system is installed by pipe dr. Best mini split on the market.

[@MikeyPipesOrlando]

Glad you like it!

[@tuffram2165]

@MikeyPipesOrlando I've. Been on you for a couple years about installing them but iirc you can't get them in NY? Which is nuts

[@cengeb]

Mitsubishi are indeed the best, all others try to copy, I have 5 in my house, heating and cooling keeps me comfortable all year long, in silence and SEER of 28 and more

[@scotts4125]

Christian pro tip. I'm in So. Florida and mounted mine on a hurricane bracket same block and stucco wall. This will go against everything you know but trust me. When drilling Tapcons DO NOT use hammer mode. Just use drill mode. It takes a minute longer but no strip outs. If you are drilling a bigger hole from the block side out to the stucco side as soon as you just breakthrough drill from the stucco side in. You will have much less of a stucco blow out. The best low voltage guy I have ever met taught me about not using hammer mode. Since I tried it I have not had 1 stripped Tapcon hole. I would say before doing it this way 25% were stripped out. Yes the wire thing works but now i don't have to do that.

[@MikeyPipesOrlando]

Thank you so much for that. I never thought not to use the hammer mode when drilling in a tapcon.

[@kat2641]

I have in the past match the angle to the house. Level said was not level but it looked level with the crooked house. Tuff call at times 🤷🏻‍♂️ but if we match the house it doesn’t look like we put it up crooked 🤦‍♂️😂😂 Nice job !! Very neat install 👍

[@MikeyPipesOrlando]

Thanks so much! Would you mind leaving us a Google review? g.page/r/CRzew4MImYRZEBE/review

[@kens.3729]

Keep Up the Strong 💪 Efforts, Christian. 👍🙏

[@MikeyPipesOrlando]

Thanks. Please consider leaving us a Google review: g.page/r/CRzew4MImYRZEBE/review

[@jeromesosnoski7001]

Looks good nice job sure customer was Happy keep up the good work.

[@MikeyPipesOrlando]

Thanks 👍I really appreciate it. Can you give me a review here? g.page/r/CRzew4MImYRZEBE/review

[@cengeb]

keep the condensate pipe below the refrigerant lines, it does matter

[@MikeyPipesOrlando]

Thanks for sharing again

[@scottmaz4063]

Great job Christian

[@MikeyPipesOrlando]

thanks

[@cengeb]

yeah need the rest of the line hide, they have a bottom fitting to finish it off, so it looks better, and also there are ty Rap bases on Mitsubishi line hide, to keep tubing and everything inside line hide secure, Even Rector seal has thinner line hide, but has ty Rap bases that snap in

[@MikeyPipesOrlando]

Hey, do us all a favor start your own KZbin channel and install the systems yourself

[@josephcorry6443]

Is it possible to install a Mitsubishi with analog gauges or do I need to buy a digital micron gauge?

[@cengeb]

should get the H2i+ models, much better SEER, and heating efficiency

[@MikeyPipesOrlando]

You got a wealth of knowledge maybe you should start your own KZbin channel

[@cengeb]

E=MC stupid, that's me

[@scottmaz4063]

#1🎉

[@MikeyPipesOrlando]

hi

[@cengeb]

Nylog on the flares?

[@MikeyPipesOrlando]

Tell me where in the manual for installation does it specify using nylog?

[@cengeb]

@@MikeyPipesOrlando highly recommended. Sometimes above the minimum is better. Not on the threads, just the flare