Mitsubishi VRF | how to fault find error code 6607(noise filter PCB)

[@LRBennettInc]

Finally a expert Mitsubishi service tech!! Thank you very much

[@BonMj]

Welcome

[@u5t636]

Hi how are I've a question about The indoor unit doesn't have a signal to the remote control

[@florencionolido5288]

Good day sir Bon!thanks for sharing your knowledge 🙏 im terry from jeddah working.

[@BonMj]

Hi, thanks

[@oiltubewalker]

Noise f supply&output by vac, not required to wait for vdc to drop unless inverter pcb failure

[@jaykenlopez6771]

What is the cause that the boise filter is not supplying DC voltage to the control Board ? Thanks.

[@BonMj]

Replace the pcb

[@muruganantham595]

How do we conduct the test run from outdoor dip switches for this model ? Can you please tell for us ....

[@dayronchagoyen402]

Usually what is the voltage DC between P and N ?. Thanks for reply.

[@BonMj]

P and N just for checking the DC voltage At inverter PCB. The voltage can up to 500VDC. For safety issues.

[@BurhanSOG]

I hope the health will always be given, mister

[@BonMj]

Thanks🙏🙏

[@Kai-18v]

Hello sir bon. How to see refrigerant quantity at deep switch?? At VRF Mitsubishi

[@kusariyanto9197]

how to determine the damage to the filter pcb? thank you

[@shivaHVAC]

Super sir...you are great

[@BonMj]

Thanks bro

[@maheradous9257]

Sorry . I mean all new video don't forget share to me thank you.

[@JavierEduardoGonzalez-iu4ze]

Condensadora PHY-450 al.momento de querer encender los relay de la tarjeta control pcb clichean y no enciende los led que puede ser ?

[@BonMj]

Check pcb

[@sirawing828]

sir, what is the cause of the mitsubishi 1 indoor unit vrf ac not cooling enough? clean evaporator

[@BonMj]

Many reasons

[@maheradous9257]

Good job 👍

[@BonMj]

Thanks 👍

[@shreekanay698]

Thanks Sir, great information....

[@hermanfung8888]

Mitsubish how to test running ?

[@chunhatminh2015]

Do you sell that broken old PCB? I want buy it.

[@BonMj]

No

[@jhonmichaeldalisay1653]

hi bon, may i ask , ah hav vrf sytem also mitsubhi, 3 units were bring 2 times in inddor cassetes , i already change pcb inddor & thermistor but still desame error,, how ca i fix this? thanks

[@BonMj]

Sorry for late reply. Try check TH 2 or TH 5 thermistor

[@jhonmichaeldalisay1653]

@@BonMj sir i already replaced those sensor with new both including indoor pcb main , but still p2 error, is it possible related to low refrigerant? the current pressure of suction is 115 psi only.

[@BonMj]

@@jhonmichaeldalisay1653 what is your outdoor model ?

[@Jrbdhome]

Think you for video🇧🇩

[@BonMj]

Welcome

[@destroyandrecreate]

Can i use this method to troubleshoot pumyp125vhms vrf mitsubishi,is it the same?

[@BonMj]

For checking is same,but some design are different

[@karaors8970]

Nice Job 🇹🇷👍

[@BonMj]

Thanks

[@peramaraj2763]

I have a doubt sir error code 6607 pcb set address 009 CRC appear 009 but wire remote control only view m-net address 015 why like this ?

[@BonMj]

Try reset outdoor power

[@wongcmy9373]

Hi sir, I have replaced the N NET board and the outdoor control PCB, but the error code 7113 still happened. How could I solve it, thanks?

[@BonMj]

7113 Check inverter board and control board wire connections Dip switch setting ,correct?

[@wongcmy9373]

@@BonMj The control board wire connections and Dip switch setting are correct. check the inverter board P - N 550 VDC ? thanks

[@nickymorley4949]

Maybe you should add, for clarity, that a 6607 fault is normally caused by a lost indoor unit.....😁

[@HotdawgMusicStuff]

I have a fault with an outdoor unit (address 52) with error code 6607. There is no LED lit up on the control board so I think this board is faulty. The other condenser unit coupled with it is address 51 with error code 7100 for capacity error but it still runs full speed and the attached FCU's are cooling ok. I suspect the unit with address 51 has error 7100 because the unit address 52 with error 6701 is not operating to provide full capacity to the system. I also have another outdoor unit on a different system with 3 x outdoors(address 58,59 & 60). Address 58 has the same error 6607 but there is power on the control board LED so I am confused. The video states that no LED lit up on control board but with AC and DC power supply means faulty board.

[@wilsonalfredo436]

good evening teacher my name is Wilson Alfredo I live in Angola Africa and I would like to know how much the set of these Mitsubishi plates costs I work with these types of devices and here it is difficult to clean these types of material Moisés filtro, control PCB e Filtro PCC..?

[@BERESHIDA2008]

ALfredo those are not very cheap parts , but they depend where you live

[@laworder6092]

Cheers buddy

[@BonMj]

Thanks .

[@mbl4689]

Is it possiblity cause by indoor for this error 6607?

[@BonMj]

Yes.check controller

[@mbl4689]

If yes, is it FCU main PCB or other spare parts?

[@BonMj]

@@mbl4689 check remote control or system controller got problem may be

[@BonMj]

@@mbl4689 indoor if one of the pcb faulty ,only the unit cant on.for other still can work

[@mbl4689]

The CU just 1 to 1 replace few days ago.. 😅 then start error 6607

[@EncikTangga]

Thnx share ilmu

[@BonMj]

Thanks

[@technicalmindkhan5573]

Vrf unit Error 2502 and 32 show error sir how to soled

[@janshaw5472]

i can't make out contrl filter and inverterpcb 😅

[@windyoceanrise]

Hi Sir, our team encounter error code 6600.. how to solve overlapping N-MET address?

[@windyoceanrise]

Mitsubishi PUCY-P300YKA 2 units with same address.. how to set? thank you very much for the reply

[@BonMj]

6600 Check all indoor unit address . (1 to 50) Check all outdoor address (50 to 99) If found the address wrong setting,please correct it. Off the power supply all indoor unit and outdoor unit and system control more than 5 minutes and on back

[@BonMj]

@@windyoceanrise 2 outdoor units should set, Example master unit 51,slave unit 52

[@BonMj]

Or CU 1 (51) CU 2 (52) CU 3 (53) CU 4 (54) Indoor FCU 1 (01) FCU 2 (02) FCU 3 (03)

[@terrychoo5940]

Usually 6607 is PCB issue ?

[@BonMj]

6607 communication problem, normally power trip or outdoor pcb faulty.

[@merwingibit7685]

how to trouble shoot error code 5301

[@BonMj]

Pls check inverter board. P & N =550 VDC

[@bibin3807]

Bro it good make a details video

[@BonMj]

Thanks

[@merwingibit7685]

sir tanong q lng pano po itrouble shoot ang error code 5301

[@globaltecnicianworldsbest3031]

👍

[@BonMj]

Thanks

[@maheradous9257]

Please all new video don't share to me. Thankyou.

[@rootievlog7020]

Are u hiring?

[@BonMj]

No.sir.

[@naveeedd]

Annoying music, unclear instructions