Jobbing job for a plumber....and terrible pipework under a kitchen sink Dont forget to subscribe to the channel....
@s.wilson56752 ай бұрын
When I see the title, "Plumbing Fail!! Pipework is Terrible!!", I thought good to see Mark's improved! It's not until watching the video I realised what you meant! Great video Mark and great looking pipework at the end. I hope you enjoyed your early day.
@MJTiffPlumbing2 ай бұрын
Thanks mate 👍🏼👍🏼
@tkthebear9842 ай бұрын
Splendid job Mark 👍. You can always rate a plumbers work by looking under the kitchen sink 🙂. Great video as always 👍
@MJTiffPlumbing2 ай бұрын
Thanks mate 👍🏼👍🏼
@paulreece71482 ай бұрын
In my opinion the way that tap fixes to the sink is the best most solid way there is. Great idea.
@MJTiffPlumbing2 ай бұрын
Yep they are great ain’t they👍🏼👍🏼
@johnwaby43212 ай бұрын
That's tidied the pipes up,.very nice 👍👍👍👍 Good news on those extra long sockets coming out 👍👍
@MJTiffPlumbing2 ай бұрын
Thanks John 👍🏼👍🏼
@CEO7862 ай бұрын
Really neat job, great work.
@MJTiffPlumbing2 ай бұрын
Thanks pal
@stephendavies9252 ай бұрын
A box spanner and a stubby screwdriver is always good for me
@MJTiffPlumbing2 ай бұрын
Yep that always work👍🏼👍🏼
@fabianmckenna81972 ай бұрын
Me too but then I've only had to install two sinks at home.
@markhannan47122 ай бұрын
Much neater than before Top job
@MJTiffPlumbing2 ай бұрын
Thanks Mark
@Smart_fix2 ай бұрын
Great job Mark well done 🙂👍🏼❤️
@MJTiffPlumbing2 ай бұрын
Thanks mate
@Dystopia952 ай бұрын
Lovely job there mate. Looks much tidier. I’m relatively new to plumbing, and don’t know what the double check valve is for. Could you explain why you used it in that situation? Thanks mate!
@MJTiffPlumbing2 ай бұрын
Thanks mate. Double check valve is to stop back syphonage…. So the water doesn’t go back into the cold supply…. Basically a one way valve
@robcoppin56992 ай бұрын
Kitchen fitters strike again......Nice job on tidying it up mate......I think we've all had the same problem with the Nerrad sockets so glad to see they're addressing it also i use that paste so i'll be looking into into the WRAS side of things with it....I hope it's still ok because there isn't nothing out there yet to rival it 🤔
@MJTiffPlumbing2 ай бұрын
Thanks Rob…… someone messaged me saying the V2 is still WRAS approved 👍🏼👍🏼
@jimh40722 ай бұрын
This is just like my previous house, every pipe in bathroom, kitchen and central heating system ended up being replaced as they were a total shambles. 😂
@MJTiffPlumbing2 ай бұрын
Makes you wonder what people think is acceptable
@robertpeters85312 ай бұрын
Great video Mark liking the butterfly valves are they full bore? Neat and tidy job just how it should be. I’ve had to do this myself a few times and it can def take a lot longer than a normal tap replacement. Thanks again.
@MJTiffPlumbing2 ай бұрын
Yep always full bore mate…👍🏼👍🏼
@chrisholt24742 ай бұрын
Hi Mark, a nice tap change and some pipe work there, it certainly did look better when you had finished. The new deeper Nerad tap sockets are a great idea, have a great remainder of the week, take care, regards Chris. 👍👍👍
@MJTiffPlumbing2 ай бұрын
Thanks mate….. ironically I needed them on this job🤣
@keithcampbell72142 ай бұрын
Neat and tidy, looks the part, another good job, well done Mark😊
@MJTiffPlumbing2 ай бұрын
Thanks Keith👍🏼👍🏼
@mattundercoat2 ай бұрын
I can honestly say I’ve had bowel movements I’m more justly proud of than that original pipe work. Looks a ton better now, and all in the space of an hour, going by the clock behind you.
@MJTiffPlumbing2 ай бұрын
Hahaha…. So bad what people think is acceptable
@michaelsharpin33692 ай бұрын
Great video Mark. Was wondering on the outside tap pipework does the iso valve have to be after the check valve or does it not matter.
@MJTiffPlumbing2 ай бұрын
Doesn’t matter as long as the valve is there 👍🏼👍🏼
@robertking98242 ай бұрын
What press tool are you using Mark? Thinking it’s about time I invested in one! Great job bud.
@MJTiffPlumbing2 ай бұрын
Novapress mate…. Great press tool
@josephfelts65602 ай бұрын
Yeah, job done, job won. Wonder who installed the pipework before, surely couldn't be a plumber, with those cable clips!! 👍👍
@MJTiffPlumbing2 ай бұрын
Kitchen fitters having a go at plumbing 🤣🤦🏻♂️
@CEO7862 ай бұрын
@@MJTiffPlumbingabsolutely
@wizard1963uk2 ай бұрын
i love watching your videos mate ..can i ask a question i have just fitted a mixer tap on a new bathroom sink and the water coming out is so slow i mean really slow the old taps was fine any idea what to check thank you
@MJTiffPlumbing2 ай бұрын
Where were the taps from??….. sometimes the way they are made can affect this…
@wizard1963uk2 ай бұрын
@@MJTiffPlumbing thanks for the reply and if I remember they was from wickes
@nickcollins75682 ай бұрын
The Nerrad tapex kit is great but they need some bigger sizes for the taps that use the fixing bolt like a banjo bolt as an outlet for a tap with a flexible hose outlet.
@MJTiffPlumbing2 ай бұрын
New kit coming soon 😉👌🏼
@lewib85262 ай бұрын
It is annoying about the Nerrad Tapex kit have come across this issue a couple of times, do you know how much extension kit will be? Also I’m so glad I bought the angle jaw set for my gun, Best thing I did. Pricey!!! But has gotten me out the S#!? Plenty of times.
@MJTiffPlumbing2 ай бұрын
Yer deffo need some angle jaws I think. Not sure on the price of the kit…. Maybe £80 I would think
@tonymurff52342 ай бұрын
IKEA special edition traps 😢😢, You will a bigger van Mark for all this fancy new equipment 😂 😎👍🤜
@MJTiffPlumbing2 ай бұрын
Hahaha….. very true
@Ragnar85042 ай бұрын
They're a bit of a nuisance outside Scandinavia these traps. In Scandinavia it seems all drains go down into the floor and then these traps make total sense. If the drain goes into the wall they don't.
@ian.M4402 ай бұрын
As always nice job
@MJTiffPlumbing2 ай бұрын
Thanks mate
@Snowy-962 ай бұрын
For them long threaded bars that you need deep long sockets for why dont you cut the excess off so that you can get your socket on there or get some automotive ratchet spanners with a flexi head ? Good job as always tho lot neater than before 👍
@MJTiffPlumbing2 ай бұрын
Thanks mate…. Yep that’s one way…. Or just get the small adjustables up there 👍🏼
@sa45402 ай бұрын
Some advice please, when I try to connect compression to push fit pipe, it never holds. I also am never able to put the olive on with the inset in. It’s made me worried about ever combining them.
@MJTiffPlumbing2 ай бұрын
You need an insert buddy
@SouthWestWildernessScotland2 ай бұрын
Mark, I'm sure it say that it is WRAS Approved in the side tin? Does that paste have to be used up in a certain length of time? Only asking as my tin has been opened for a long time.
@MJTiffPlumbing2 ай бұрын
I’ve had tins opened for years and still used them 👍🏼👍🏼
@nigelchapman70972 ай бұрын
I hate the IKEA Flexi waste pipe very hard to make it look tidy. Nice job only 1 thing i thought it was isolation then check valve ?
@MJTiffPlumbing2 ай бұрын
Thanks mate…… I’ve done it both ways if I’m being honest
@skysantana31782 ай бұрын
Great work mark how come you didn’t pick up a tapex extension kit while you was at the show 😄 they could of given you a free set as you always praise the kit 😄👍
@MJTiffPlumbing2 ай бұрын
Not no n sale yet….. I think I may have one coming to review and do a video on though 👍🏼
@glyndavies5912 ай бұрын
From untidy to tidy looks good now had to laugh when you used the trusty adjustables to remove the old taps some of these tap changes can be a fiddle
@MJTiffPlumbing2 ай бұрын
The irony eh🤣🤣🤦🏻♂️
@mmm0910002 ай бұрын
Builders job I suspect 😡 can’t plumb to save their lives, not all of them’ just my experience ! plastic fantastic 😂 great vid mate ps…the paste is fine’ load of bollocks 😂
@MJTiffPlumbing2 ай бұрын
Thanks buddy
@TomRedshawPK2 ай бұрын
great little video as always 👍 ive had the angled jaws and tbh i think youre better off doing it the way you do, with a bit of pre-planning, they really dont make much of a difference and are just as much of a pain to use. great stuff as always mate.
@MJTiffPlumbing2 ай бұрын
Thanks mate……. 👍🏼👍🏼…..
@MikeSargeant-x1h2 ай бұрын
Why do you use full bore isolation valves when the pipework connects to flexi pipes with an internal bore of 10(?) mm? Thanks.
@MJTiffPlumbing2 ай бұрын
Always have…👍🏼👍🏼
@albertmcivor8792 ай бұрын
Neat job although I would have put full bore on hose tap pipe.You can get them in press ballofix type.And bes has side jaws on sale
@MJTiffPlumbing2 ай бұрын
They are full bore……👍🏼
@albertmcivor8792 ай бұрын
@@MJTiffPlumbing I am on about the balofix valve for the hose tap.Doesnt look like full bore to me.
@jamesscrutton46592 ай бұрын
Hi Mark double check valve is that a non-return valve
@MJTiffPlumbing2 ай бұрын
Yes mate 👍🏼👍🏼
@thomascoyne1572 ай бұрын
I’m all tapped out 😂👍👍👍🇬🇧🇬🇧
@MJTiffPlumbing2 ай бұрын
And me🤣🤣
@edmondchege73812 ай бұрын
Good job mate
@MJTiffPlumbing2 ай бұрын
Thanks buddy
@smarshall1109882 ай бұрын
I've had an issue twice with the swivel part falling apart. They've sent a new one and it's happened again not sure if it's a dodgy part, I've only used the kit less than 5 times
@MJTiffPlumbing2 ай бұрын
Which part do you mean
@seankay81372 ай бұрын
Can press-fit be used in non accessible locations such as under a shower tray or would you solder them? Cheers
@MJTiffPlumbing2 ай бұрын
Can use it anywhere you can get the tool into mate 👍🏼👍🏼
@liamkaizen47852 ай бұрын
Great job but I thought the regs state you need to have a drain off valve on after the isolation and check valve do you can then isolate and drain the pipe out through winter, that’s how I’ve done them anyway
@MJTiffPlumbing2 ай бұрын
Just turn it off and open the tap outside…. Expansion has somewhere to go then. Check valve is regs
@liamkaizen47852 ай бұрын
@@MJTiffPlumbing Fair enough, personally like to just stick a drain off on the pipe inside and drain in completely then
@MJTiffPlumbing2 ай бұрын
👍🏼👍🏼 no harm in it
@Fordy1172 ай бұрын
Them ikea kitchen units and wastes are stuff of nightmares
@MJTiffPlumbing2 ай бұрын
Yep… I agree
@brianmckenna34402 ай бұрын
Great video Tiff Mate
@MJTiffPlumbing2 ай бұрын
Thanks mate
@geometryexplainseverything49262 ай бұрын
Those milwaukee automatic pipe cutters are rubbish on 15mm, still using my pipe slice, too! Just a thought don't ALL outside taps have double-check valves built into their bodies ? Therefore, there is no need for adding an extra one?....
@MJTiffPlumbing2 ай бұрын
You have to get the specific outside tap with check valve in, not all come with them. Plus don’t even bother using them as they freeze up in the winter and shatter the plastic, then don’t have a check valve at all, always best to fit them internally
@IsicobezАй бұрын
Would one of them tappex sockets not have fit over the end of the box spanner if you were in a pinch, if that makes sense
@MJTiffPlumbingАй бұрын
Good shout that
@simmo3212 ай бұрын
Some of the positions we have to get into! 😂
@MJTiffPlumbing2 ай бұрын
Oh mate…… back breaking
@grahamatkins88452 ай бұрын
Mark great video but you say 4 or 5 tap jobs a day but as a ball park figure what would you charge for 1 job just curious,,,,regards
@MJTiffPlumbing2 ай бұрын
£80 give or take…. For a straight swap
@grahamatkins88452 ай бұрын
@MJTiffPlumbing thanks Mark that's what I charge Been Plumbing 15yr as I said just curious many thanks for your time
@MJTiffPlumbing2 ай бұрын
No worries buddy
@JonCooney-m2hАй бұрын
We never use compression on plastic pipe because too much expansion on the plastic. Also if you are you need to use a metal insert.
@MJTiffPlumbingАй бұрын
Never had an issue using them on plastic….. we all do what we are confident with 👍🏼
@ronnierobinson15022 ай бұрын
Put the socket on without the extension in then it sometimes gives u that little extra to get it ....or its the old fashioned box spanner
@MJTiffPlumbing2 ай бұрын
Or the new extension kit😉😉
@ronnierobinson15022 ай бұрын
@@MJTiffPlumbing too right ...until i get it tho
@BestUserNameUKАй бұрын
Buy a cheap set of 'crows feet' spanners😉
@MJTiffPlumbingАй бұрын
Good old crows feet
@itwillbenicewhenitsfinished2 ай бұрын
Is it metal or plastic inserts that are needed
@MJTiffPlumbing2 ай бұрын
As long as they are bracing the pipe you’re good…..
@neillwalker56812 ай бұрын
What do you charge for an average tap change like that?
@MJTiffPlumbing2 ай бұрын
A straight forward in and out tap change is £80
@alansmith94122 ай бұрын
everytime you go under a new kitchen its kitchen fitters and builders plumbing then you have to say to the customer we need to start again
@MJTiffPlumbing2 ай бұрын
100% mate
@mistermikeanson2 ай бұрын
I cannot understand why they can't do a neater job!!
@ianbrooks68162 ай бұрын
Pipework to outside tap ain’t that good is it? And why not sort out that waste while u were there?
@MJTiffPlumbing2 ай бұрын
Are you asking me or telling me🙄…….
@jamesbell76492 ай бұрын
New press gun, want to sell me your old one mate 😂
@MJTiffPlumbing2 ай бұрын
Same one…. Different cover😉
@mastercraft57982 ай бұрын
Why do people/plumbers/kitchen fitters leave the threaded bolt so long? It takes 30 seconds to cut it down to an appropiate size so that a regular socket set can be used to tighten and/or undo it. Then, there would be no need for expensive 'Tap socket sets' that are clearly not fit for their job ( unless you spend even more money buying extended/long reach sockets that should have been included in the original set!). Just go buy yourself some long reach sockets... I've been using them for years!
@MJTiffPlumbing2 ай бұрын
What happens when the long rod is all ready on and your trying to remove it😉👍🏼👍🏼
@evervol12 ай бұрын
They leave the bar the size it was supplied for a very good reason... believe it for not if you cut that threaded bar it voids the guarantee for the tap, crazy I know!
@colintowndrow95012 ай бұрын
@@evervol1Really? I don't recall ever seeing that in the paperwork. Will have a good look next time.
@evervol12 ай бұрын
@colintowndrow9501 some state that if the stickers are removed from the flexies that voids it aswell 🤣
@mastercraft57982 ай бұрын
@@evervol1 Haha, you got me.
@richardlewis53162 ай бұрын
Re the long threaded bar on some taps. I still use the long box spanner which comes in a pack of 3 for about £6.00. They slot tgether and I don't need to buy the fancy set or spanners for I bet £120!! Why paste on plastic pipes? Why paste at all!! It went out with hemp!!
@MJTiffPlumbing2 ай бұрын
Why would you NOT paste on fittings….. it takes seconds and seals well….. And yep, everyone has the £6 box spanner’s….. 👍🏼
@1nice12 ай бұрын
Box spanner’s ( cheap )
@MJTiffPlumbing2 ай бұрын
Yep…. They are
@SuperWayneyb2 ай бұрын
I could do with those longer sockets 👍👍
@MJTiffPlumbing2 ай бұрын
Out very soon I think👍🏼👍🏼
@SuperWayneyb2 ай бұрын
@@MJTiffPlumbing Cool I missed them somehow at Installer 👍👍
@JonCooney-m2hАй бұрын
Surpised you never changed the crappy waste
@MJTiffPlumbingАй бұрын
Wasn’t an issue for the customer so didn’t need to..👍🏼
@JonCooney-m2hАй бұрын
@@MJTiffPlumbing You're right less agro the better lol
@chrisw58292 ай бұрын
Would have pre pressed all the tee, then tightened the full setup o to isolation valve,
@MJTiffPlumbing2 ай бұрын
Yep always so many ways of doing the same job
@neiltwaddle96652 ай бұрын
Honestly my friend..I do 6 mixers a week ...add a full set of Wera Hollow nut spinners to you're kit.....Easy..save yourself a lot of pain .
@MJTiffPlumbing2 ай бұрын
Will take a look mate
@stevedoherty40222 ай бұрын
What is this magic you speak of?
@hewoguys25062 ай бұрын
someone need to invent something that secures taps better coz its one job i bloody hate it is so annoying to do
@MJTiffPlumbing2 ай бұрын
Good shout that mate 👍🏼👍🏼
@tomobrien84172 ай бұрын
Romanians and pole ish. Do love a push fit on IKEA crap .great vid mate your beging to sound like me oid school plumber .😂
@MJTiffPlumbing2 ай бұрын
100% right buddy
@richardlewis53162 ай бұрын
Under a sink - push fit is so much easier!!
@MJTiffPlumbing2 ай бұрын
If you’re a DIYer maybe…. But any good plumber will not have pushfit where it can be seen…. Well, not any respectable plumber Not for me mate……
@richardlewis53162 ай бұрын
@@MJTiffPlumbing Under a sink is hardly on view!! OK compression fittings. Easier to adjust than press fit!! Maybe we agree to disagree!! Oh and whay all that apste!! Never used it!! Ha ha
@llamedosr78432 ай бұрын
Black taps,obviously not a hard water area
@MJTiffPlumbing2 ай бұрын
It’s probably the hardest water area in the country🤣🤣🤦🏻♂️
@Jeff-bg7pt2 ай бұрын
The pipe work was a mess
@MJTiffPlumbing2 ай бұрын
Yep
@TomasAuskalnis-e2f2 ай бұрын
Garden tap feed looks ugly... Ufff
@MJTiffPlumbing2 ай бұрын
Not for you then??
@Chubby_T05112 ай бұрын
Get what you pay for. The original job was clearly the cheapest quote.
@MJTiffPlumbing2 ай бұрын
Think it was the kitchen fitter 🤣🤦🏻♂️
@heatpump85662 ай бұрын
Watching g the first minute, that’s a kitchen fitter install! Shabby and awful
@MJTiffPlumbing2 ай бұрын
Yep… typical kitchen fitters🤦🏻♂️
@SuperWayneyb2 ай бұрын
🤘😎🤘🫖☕️🍪🎥👍👍
@MJTiffPlumbing2 ай бұрын
Evening mate
@SuperWayneyb2 ай бұрын
@@MJTiffPlumbing Evening Bud No loft jobs being done this week 😂😂😂😂😂👍☀️
@MJTiffPlumbing2 ай бұрын
Not a chance mate….. I’ve been doing the decking in my garden all day🤣🤣
@SuperWayneyb2 ай бұрын
@@MJTiffPlumbing been double boarding a ceiling and even with a board lifter I feel broken 🤣🤣🤣🤣🤣🤣🤣🤣🤣😓
@namAlexander2 ай бұрын
lol , i am no plumber but do my own to and extent just some people really need to throw there tool bag on Fb market place for free and let the common sense people have the tools, ive done a better job using the force lol, remember the fitting the tap and tails trick i did that not long after i watched your vid, your like WTF is going on that easy lol
@MJTiffPlumbing2 ай бұрын
Your no spelling guru either mate 🤣🤣🤣
@namAlexander2 ай бұрын
@@MJTiffPlumbing i am not but Education don't make you intelligent lol, think you took it all the wrong way
@MJTiffPlumbing2 ай бұрын
Tbh mate I’m not sure what you’re on about….. sorry
@namAlexander2 ай бұрын
@@MJTiffPlumbing It does look a bit beer talk lol , last part was about that vid you did fitting the tap without faffing around underneath, I did it a few months later on Kitchen tap