MK60 ABS Install Overview (S13 240SX)

[@ElectricSuperCar]

I have a habit of watching any video that KZbin recommends with less than 1000 views. It is my way of helping the smaller channels!. Keep ot up

[@VictorPitstop]

Excited to see the results on track!

[@FlatBlack_240SX]

Interesting fact/update: I am converting from 48 tooth tone rings to the OEM Nissan 46 tooth tone rings. I drove my car with the 46T rear rings and 48T front rings and it worked just fine, so I guess you don't even necessarily need to match the tone ring teeth count, as long as they are close. I assume this is for tire diameter differences, and other total tire height variables.

[@FlatBlack_240SX]

Confirmed today that the Yaw sensor is not required for ABS to function

[@th1_s138]

That would be great if you would give us a update/review of it working at the track

[@FlatBlack_240SX]

It is amazing! I mounted the module near my hip, and you can hear it click when it's working, which is great audible feedback for low-grip sections of the track. At an event in September, I could hear it clicking through a high speed corner where I was trail braking just slightly to get weight on the nose of the car, and I could hear it activating ABS as the unloaded/inside tire was trying to skid. I never would have heard that skid without ABS and the functionality is super effective. I can focus on my corner entry and other inputs now that I don't have to hyper-focus on the corner entry and listen very closely for a skidding tire.

[@ApexAdventures.]

Great vid! Just got a module for my subaru and following the same principle and thanks for the vid as there is not much out there Just a Q on the data you are getting from the k-line can data, what are you using to read that data (i see you referenced a kline obd reader cable) but wht software are you using to see the wheel speeds etc? Im going to be wiring in speeds etc to a digital dash but want to be able to test all of this first before i do that kind of wiring Thanks mate

[@FlatBlack_240SX]

The software is called "INPA" - from what I understand, it is a reverse engineered and English language translated version of a BMW diagnostic software. There are links on BMW forums, you'll need to Google "INPA download" to find a currently hosted version

[@ApexAdventures.]

@@FlatBlack_240SX thanks mate

[@ap9engineering]

Great overview! Does the rht setup also have abs warning light?

[@FlatBlack_240SX]

Yes, the RHT harness has a labelled wire for the ABS warning light, but there are also diagrams for the harness pinout (check the links in the description) if you want to DIY it

[@andrewlintz9639]

Are you using 3/16 line from the master or 1/4? The thread on grm says to use 1/4 but I'm stuck with 3/16 because of my fitting sizes

[@FlatBlack_240SX]

My whole car is 3/16 - the line size shouldn't matter.

[@th1_s138]

Hi ! i already have an s13 Silvia with ABS ( crappy ) , so does it mean the installation is a lot simpler ? I also have GKtech diff cover with provision for dual 300zx sensor not sure ?

[@FlatBlack_240SX]

I'm not sure what the OEM ABS tone rings look like on the front of an S13 but yeah I'm using OEM S14 hubs/ABS rings and OEM G35/37 rear sensors on ABS-ring-5-bolt axles (from a Z32). It should be much easier. I've heard the 90s Nissan stuff is 3-channel, do you have 3 lines coming out of your brake master cylinder or just 2?

[@th1_s138]

@@FlatBlack_240SX yes oem is 2 sensor in front and one on diff input shaft. i have 2 lines coming out of MC and going to the ABS module .

[@th1_s138]

@@FlatBlack_240SX i think that would be the best way to go for me as well . I think the 350z sensor are bolt-on for my diff cover and i would just need to machine fit Dual tone ring on my 6 bolt axle ( s15 helical read diff )

[@FlatBlack_240SX]

@@th1_s138 Well that should simplify things a little bit - you shouldn't have to redo your brake master lines or the front wheel brake lines from the ABS module. You'll probably have to add a line to one of your rear wheels if it's a single line to the rear with a split near the rear subframe like mine was.

[@s-chassis]

@FlatBlackable, Did you have part number of this sensors?

[@FlatBlack_240SX]

No, I got them from the junkyard but I believe this is it for the fronts: www.amazon.com/Front-SENSOR-Replacement-Nissan-Maxima/dp/B09F3L3JY8/ the rears are off a G35/G37 diff cover