RAM Alfaobd 101, What is needed?

[@rolandsalazar5911]

Great video! Finally someone talking about using AlfaOBD and explaining that for RAM 2019+ I needed a security module bypass cable. I bought the OBDLink MX+ and had no problem connecting to it and downloading truck ID information but I could NOT make any changes because the ECM was not responding back to my changes. I believe the missing piece was this Security Module Bypass cable, thank you!!

[@BACKYARD_DUMMIES]

Can I set up Speed Limit For my Service Truck to 70MPH I don’t want it to go Faster than this. This is My Company Service Truck

[@zachderr213]

I have the mxlink+ on order with a Chrysler 12+8 programming cable. Is this going to work? Or do I need the security module bypass cable in addition to the 12+8? It’s so hard to find reliable good information about Alfaobd

[@gobluekurt]

Can you do forced manual regen on 2019 using these three items?

[@brustar5152]

@@zachderr213 Depending upon year, model, you might need a different security bypass cable as my truck is a 2020 1500 DS model and it does no have a security gateway module so the 12/8 bypass I bought was useless along with the later bypass cable I purchased (BOD) to plug directly into the can buss receptacles under the dash. That one came with a cable with two male plugs of the same size but the two buss bars have different diamter pins - so again - useless I have so far invested in the MDX + , the Alfa software, two different by pass cables and have wasted my money so don't get too intriqued with this until you firmly establish what your system actually has by way of security lock-out system.

[@tetedemarc]

Is there a list that describe the features we can change and/or enable . Some are self explanatory but others I have no clue what the feature description mean. Thanks

[@BillyWaggs4052]

Hands down the biggest waste of money I have spent on a tool in a long time. Harness...Software...OBDII device...all for nothing. Windows version of Alfaobd is absolutely trash and the company offers zero support. If you are looking for a more user friendly approach do NOT consider Alfaobd or any of this mess this guy is talking about. I am seeing more people having the same level of success I am having with these products than having the results show in this video....

[@MKSPerformanceOffroad]

What issues are you having? I have seen alot of people have success with this once they do a little research and ask for some help if needed. We use this and our hardware with zero issues on a regular.

[@BillyWaggs4052]

Yes and I believe in every video you have displayed the use of it you are using an android tablet correct...? We have windows based tablets and laptops in my shop and though we can connect via bluetooth to the OBDLink MX+ the software will not actually see the divice... We are an electronics based business and have been building touchscreen dashes based of CANBus communication for a decade now. I can appreciate the suggestion of asking questions and such but trust we HAVE been asking and Alfaobd only replies with the same rubber stamped response that does NOTHING to address the Windows connectivity issue and only suggests we use an android based device. And yes...absolutely could do that. But we bought a product that is said to work with a Windows platform and that simply is not correct. And to think...All we wanted to do was activate fold in mirrors we added to our service truck... My original comments stands...I am sorry... I think this product is a perfectly good waste of money... And it is not based off anything you have shared but the software company's total lack of support along with KAODTECH offering zero post purchase support.... @@MKSPerformanceOffroad

[@MKSPerformanceOffroad]

@@BillyWaggs4052 I have used this same software on a windows based laptop as well because it did perform certain functions better. The software manufacturer is not always easy to get ahold of and other companies like kaod tech to my knowledge dont do this full time which is why you are not getting tech support like you normally would from a large established company. I have been able to successfully help people use this program personally not through a video but walking them through the steps over the phone or even instagram. The program is powerful and can perform a bunch of procedures but you will have to do some learning unfortunately. The recommendations for use of hardware should be considered as this is directly from the developers who have tested these comms devices so we follow them explicitly. What computer system are you using, if you jump over to IG or facebook we could talk about the issues your experiencing.

[@EthanGallimore]

Can you program key fobs with it?

[@MKSPerformanceOffroad]

@@EthanGallimore yes, installed factory remote start and 2 extra keys with it no problem.

[@yogibeer9319]

I have a 2014 RAM 1500 and am going to replace the ABS module myself to save the ridiculous money the RAM stealer wants and got the OBDLinksMX+ today and am looking to get the AlphaOBD. The OBDLinks is now good for iPhone. How do you back up your factory RAM settings on your truck in case I mess up configuration? I’ve been seeing guys on these RAM boards warning about making sure you back up factory settings. Thanks for how to get pin. Great video! I’m a subscriber now!

[@danaberman6929]

Will this work with the 2023 Ram 2500.

[@MKSPerformanceOffroad]

Yes

[@antoniodavis9848]

I'm new to the software I just want to run diagnostic on my ram. I have the pc version can you help me please

[@MKSPerformanceOffroad]

@@antoniodavis9848 what model year?

[@antoniodavis9848]

2017 Ram 1500 Bighorn 5.7Hemi

[@MKSPerformanceOffroad]

@@antoniodavis9848 you likely are having issues connecting to the truck because alfaobd is set to look for the wrong comm port which your cable is connected to.

[@antoniodavis9848]

It connects to the truck but I'm not getting the information am looking for I have a start up issue, I tried to start yesterday and the truck spun over like a choke was on the motor then cut off and I turned the key off and the restarted.

[@MKSPerformanceOffroad]

@@antoniodavis9848 if you have instagram you can hit us up on there or facebook as well

[@JoseLopez-is8yt]

Does alpha obd work on Dodge charger 12 and up. I see it does for Ram.

[@MKSPerformanceOffroad]

Yes, it definitely should. You will be limited to whatever Dodge had programming wise for that year model. As we progress through the later model years the capability is greater.

[@judycrider4373]

We. Have a 2012 ram disel radio works but camera won't come in for nav.

[@MKSPerformanceOffroad]

Which camera, back up camera?

[@x-man4702]

Hello, great video, thanks for posting. Quick question: on a 2016 Promaster City (Fiat Doblo rest of the world) is the yellow obd cable needed along with obdlink LX; SX; or CX ?

[@MKSPerformanceOffroad]

Thanks for your support and question. I would recommend getting the EX or MX+ to allow you to perform any of the processes alfaobd is capable of. Im not sure what the other models will or wont do on a promaster as I have not hooked to one of these.

[@DaddyRuppe]

Does it program trailer brake ?

[@MKSPerformanceOffroad]

Yes it will

[@RoyWeintraub-i4g]

I found your video and your answers to questions regarding the AlfaOBD to be most informative. This software can do more than I require, but the cost of it & the security adapter are quite affordable. (2018 RAM 2500 Diesel).

[@cjbarlow61]

Just found this jewel of a video! Gotta swap abs modules in my 17 ram 1500. Dealership cant get the part and will not reprogram a part from a junker so im going to have to try it on my own

[@MKSPerformanceOffroad]

@@cjbarlow61 order abs module or pump from a place like mymoparparts.com or moparpartsonsale.com. They should have them available. Ordering from dealer is tricky because they all use different warehouses that may or may not have any in stock. ATL warehouse had like 130+ last time I looked

[@bishopgeorge1333]

Will I be able to download the ALFAOBD on my Kindler? Oh sorry but I have the 52gals titan fuel tank is their a setting for that also?

[@JABECO2016]

you lucky your dealer church $120 per hourly my dealer wanna charge me $190 per hour

[@TheMacmax1977]

Hi?I have 2014 Ram 1500 tradesman and I did upgrade my cluster for 7” screen and I have TPMS light in my dash,thinking can fix that?thanks

[@allanartman9936]

What is the minimum Android OS I need to run Alfa OBD

[@tattedup1189]

Your doing this off the WiFi on the tablet correct ? Then Bluetooth to the obd scanner ? Is that how it works in a tablet because i don't have android phone but i do have a tablet with WiFi and Bluetooth

[@MKSPerformanceOffroad]

You only need wifi to save the stock file to google drive before you make changes or to update the software. To use the software it is not required to have the wifi as I connect to the Obdlink MX+ via bluetooth. If you have a windows laptop you can use that as well.

[@tattedup1189]

@@MKSPerformanceOffroad i don't have a windows laptop just the tablet wish they did this on iOS but oh well. And i shouldn't have to save any settings right just make the changes on the alpha app and save three the app right. Not on google drive ? Thanks for your time

[@Relevantminded]

Heres a good question about this program, can you erase the notorious p1745 transmission line pressure variable force code and p0868 using alphaobd on a 2014 dodge grand Caravan sxt 3.6l with a 62te transmission?

[@MKSPerformanceOffroad]

@@Relevantminded great question, I honestly can't answer that as I have not had any experience with that model vehicle. I will say it will erase and clear your codes but if they comeback some troubleshooting will be required.

[@alfredarrendell9284]

I will like to know if any one can help me with my 2014 Dodge Ram 1500 Crew Cab Statemen , I also have Alpha OBD and I did something now I don't have any rear turn signals for two weeks now, I wrote everything down what I change and still nothing can any one help, no rear signal, when I hit the brakes and turn on the signals the brake lights go out, thank you, Alfred

[@MKSPerformanceOffroad]

You need to pull your original log and compare to current log to see what is different in the settings. You will need to go line by line.

[@williammanzare9250]

I have this on my phone and my laptop.both do not work.I tryed 2 security bypass cables and the one they recommended with the obdlink mx + obd2.can't get it to work on my 2018 1500 ram

[@MKSPerformanceOffroad]

What bypass cable are you using?

[@anthonypenna5961]

Do you work on Ram 2500 2022 Power wagon.?

[@MKSPerformanceOffroad]

Yes I have.

[@anthonypenna5961]

@@MKSPerformanceOffroad your location?

[@JeffGilmour-ry7zk]

Other then the software what else do I need to use this app?

[@MKSPerformanceOffroad]

What model year truck do you have?

[@JeffGilmour-ry7zk]

2018 ram eco diesel. Showing 100% filter is clogged and I should go-to the dealership. Someone told me with the alpha I can force a Regen.

[@MKSPerformanceOffroad]

@@JeffGilmour-ry7zk you will need an SGM bypass cable and an obdlink device to access the truck.

[@DanielGoudreault-kl6lg]

I have a 2018 2500m*-Ram Promaster; do i need the SGM by pass ? Is the 4 digit pin number only good for 1 day ?

[@MKSPerformanceOffroad]

Likely that you will need it as Ram started putting in the sgm in 2018. You will need to locate the sgm to verify you have one or simply call dealer and ask them, bet its behind the radio or near driver side dash somewhere near column or kick panel. The 4 digit pin is useful to have for certain procedures and started rolling every 24hrs for 2019+ so you shouldn’t have to worry about that on your 18’. Hope this answers your questions.

[@mr.anderson910]

Almost pointless for 09-12 ram trucks (non powernet) very few usable features

[@MKSPerformanceOffroad]

Depends on what you are wanting to get done and use the tool for. I wouldnt say it is pointless, however, with those model years you are limited on what you can enable or disable because the options just weren’t available then.

[@danielpark2667]

I bought the paid version and it will connect to the obd Bluetooth reader I have but I can't actually do anything with the app, it won't even Ren diagnostics. It feels like the app is locked up. Any thoughts?

[@MKSPerformanceOffroad]

What bt reader are you using now?

[@samueleverett3719]

Can you turn on the SRT package with Alfaobd?

[@MKSPerformanceOffroad]

By srt package are you referring to the splash screen option. If so, yes you can. If your talking about any additional features that come with an SRT than you would need to install those options and then activate them.

[@hhporsche83]

Great video, I have Bluedriver OBD2, will it work?

[@MKSPerformanceOffroad]

Several obd readers will work and the obdlink is the recommended reader by alfaobd. With that being said it is not the only one and yours should work just fine. I haven’t tried any others out so please leave a comment on how it worked and if you had any issues.

[@hhporsche83]

@@MKSPerformanceOffroad I will try it and reply to you

[@milosusa]

Will AlfaOBD diagnose those problems for which you get messages only, but not check engine light ? Immediately I get Service Electronic Stability Control, Service Trailer Brake System and driving for couple minutes I get Service 4WD messages . Plus message in reverse that ParkSense rear braking Off and can 't be turned On in setting . Trying to figure out what causing that or if only dealer can diagnose those problems. Truck is 2020 Ram 1500 ecodiesel.

[@MKSPerformanceOffroad]

Those are all things you should be able to see and perform with alfa obd. Forums have a ton of info on using it as well.

[@lindachatman682]

Can I program my own win module on my 2010dodge caravan with this app ?

[@MKSPerformanceOffroad]

I know I have programmed keys and remote start but Im not sure if you will be able to replace the module itself. Generally this requires more hardware like a j2534 pass through device and access to dealer level software.

[@matthewrunyon357]

Am I understanding correctly that I don’t need the bypass for a 2016 Ram 2500?

[@MKSPerformanceOffroad]

Correct, no security gateway module on trucks older than 2018.

[@davidcandao1]

Hello. Could you please upload a video how to enable/activate the trailer tpms on a 8.4” screem. Thank you for your videos. I got the obdlinkMX+ with the TTXSPP Cable Adaptor/bypass but I have no Idea how to use it and don’t want to mess with the truck without knowing.

[@MKSPerformanceOffroad]

What is the ttxspp cable?

[@garyrichards6041]

I see you have the ezlynk app on your tablet. Did you use that programmer on your 18 Ram before or after the Raceme programmer? Which one do you prefer? Did you use to have a 2003 Ram that you did videos on for a utility bed install and changing from auto transmission to a stick shift? If so you were a lot of help to me back then. I now have a Big Horn 2018 that I added things like you. Bed lights with switch, amp power steps, engine heater delete, 7” cluster, front and rear park assist sensors and a front camera. Thanks for your videos!!

[@MKSPerformanceOffroad]

No sir I had a 2014 Ram. I have not bought any ezlynk programming and strictly used it for data display. I prefer the raceme because of cost as I had already purchased and I didn’t really want to rely on my phone to display data. I use my phone quite a bit for other things. Personal preference to be honest though but there is some good stuff offered on both platforms. Thanks for the support and Im glad some of my videos helped you out.

[@davidcandao1]

Do you have a video tutorial for the front camera installation on your truck ? And where to find the parts? Thank u

[@garyrichards6041]

@@davidcandao1 hi David. I did make a few videos to explain what I did but it’s very confusing because I broke the black and red plastic harness that plugs into my 8.4 radio. I spent many hours trying to figure out how to put a front camera in but finally got it working with a lot of trail and errors. I have pictures, diagram of how I got it to work. I did tap into my cargo camera and connected a toggle switch to go between front or cargo camera. There’s a lot to doing this and I would be glad to try and help you out. Not sure how to get this info to you. Never posted on KZbin before. What year is your truck and do you have the cargo camera?

[@davidcandao1]

@@garyrichards6041 2021 ram 3500

[@garyrichards6041]

@@davidcandao1 mine is a 2018. You might have a open slot on the back of your screen to add a camera?? Do you have a big radio and not the 8.4 that I have?

[@teezytv4634]

I accidentally got the wifi scanner instead of the blue tooth one, do you know if it will work or not?

[@MKSPerformanceOffroad]

Which model is it?

[@mahal3680]

Can this program adjust the interior lighting? I have a problem with my 2017 ram 1500 where my interior lights will not come back on after inital opening of any door after the truck engines been running.

[@MKSPerformanceOffroad]

Possibly, you would need to go in and look at the options. I have been able to go in and adjust alot.

[@donsmods]

How do i know which body computer to select in AlfaOBD? I have a 2021 ram 1500 classic

[@summitbound1]

Does this have the capability of fixing a LED Headlight Bulb flicker on a 2012 Ram 3500

[@MKSPerformanceOffroad]

Yes, it should in the 4th gen trucks. I will double check to see if the option is available on a 2012. I know it is available in alfaobd on 2013+.

[@StevenHamill-h3p]

Is it capable of turning off the air suspension or service air suspension light?

[@MKSPerformanceOffroad]

It should be able to handle that task

[@BryanDoesCinema]

But how do you connect it to the car???!

[@MKSPerformanceOffroad]

You plug in the obd mx+ or cable you have and them connect via bluetooth to the comm device. After that you select the appropriate selections for make, model, year and the respective module. Select connect and then open the car with hood up icon

[@BryanDoesCinema]

@@MKSPerformanceOffroad OK I'll have to buy the cable, I thought it connected with the car's bluetooth. TY for this.

[@MKSPerformanceOffroad]

@@BryanDoesCinema no sir the obd mx+ connects via bluetooth to the tablet once it is plugged into obd2 port on vehicle.

[@uzorick]

Is that it? No dongle or OBD anything to plug into the car?

[@MKSPerformanceOffroad]

@@uzorick there is an obd comms device to plug in which is the obdlink mx+ which is required to communicate with vehicle

[@bigredman5223]

Hope you can help me out. Have to change out my BCM and got a used one but now needing to change my settings on it. How can I find my current settings and change the “new” bcm settings?

[@MKSPerformanceOffroad]

Can you access the current bcm to get the current configuration?

[@RichardL-q2n]

I have the 2019 Cherokee trailhawk. Will I need the bypass cable? Thanks for your help in advance

[@MKSPerformanceOffroad]

More than likely yes. Everything I know of 2018+ got the SGM.

[@RichardL-q2n]

Thanks

[@TheRoddrickblow]

Can this be used to change my '14 SLT to a remote start?

[@MKSPerformanceOffroad]

Shouldnt be a problem

[@jennitsu12]

Iris asking me for a yellow wire for my pro master

[@hcpmdmm]

How do I add Hill descent control to my 2021 ram 2500 using alfa-obd? I have the proper switch installed just need to activate it. Thanks.

[@frankbatista673]

Hi a good video ,Can you tell how is possile to delete AGR system on My Ram 2015 ecodiesel 3.0Lt V6.Thanks

[@MKSPerformanceOffroad]

Alfaobd is a programming and diagnostic tool. It is not possible to perform the action you are requesting. Recommend contacting a tuning professional to see what options are available.

[@frankbatista673]

@@MKSPerformanceOffroad thanks have a good one

[@hoytster138]

Will i need the bypass cable for my 2012 Ram?

[@MKSPerformanceOffroad]

No only 2018+ require the bypass

[@cymbalenthusiast3265]

Do I need to buy an older Android tablet? I've heard people have had problems with the newer operating systems.

[@MKSPerformanceOffroad]

You should be able to go onto the alfaobd website and view the OS requirements. As long as it is a good tablet or computer that has the memory you should be fine. People have issues when they try to get the cheapest tablet possible and it doesn’t have the ability to process information and run the program. If you have an android phone you can try that first.

[@cymbalenthusiast3265]

@@MKSPerformanceOffroad I have a Samsung S22 Ultra plenty of memory and processing power. I've heard people talk about it working one second then the next it doesn't because of an update.

[@RefriedMedia]

Did you have to purchase the full version of the software? The Windows PC only has a demo.

[@MKSPerformanceOffroad]

Yes you will need to purchase the full version. There should be a way to purchase it on windows in the software or on the website. It has been a little while since Ive done it.

[@QuCkScOpE]

Do I need the bypass for 2019 1500 classic?

[@MKSPerformanceOffroad]

Yes, trucks 2018+ will need it

[@TwoEye2079]

Can anyone confirm this works on 22 2500 6.7

[@MKSPerformanceOffroad]

You shouldnt have any issues. There are several people that have been able to connect and make changes

[@brickleberry7829]

Can Alpha obd be used to vin match a abs module. Original Abs module damaged and replaced with a used module? Needs vin match and configuration. So says the codes....

[@MKSPerformanceOffroad]

No Alphaobd cannot reflash a module. You would need a J2534 pass thru device with appropriate access to the manufacture reflash files in order to do what you are talking about.

[@brickleberry7829]

@@MKSPerformanceOffroad thanks

[@rsshemi]

Will this work with any bluetooth OBD scan tool?

[@MKSPerformanceOffroad]

It has but I dont know which exactly. It is recommended at least to use obdlink mx or mx+.

[@lspaccio]

Can remote start be enabled without the hood latch with this software?

[@MKSPerformanceOffroad]

I dont believe so as this would be a safety item that the bcm has to see in the start sequence

[@dashtyATG]

Hy I'm looking for the same answer Do you know 1 that can enable with out the hood latch? Or any other salutation

[@kylewaters7409]

Can I use this software to turn off the EGR system? I have a 2012 ram 3500 I want to do the EGR delete soon but I’m trying to see if I can use this to turn off the codes or bypass the system

[@justinbourassa9546]

I just ordered the obdmx+,what cable do i need to order with that to lower my tpms settings on 22 Ram 2500?

[@MKSPerformanceOffroad]

You will need to get a security gateway module bypass cable from Kaod Tech and your 4 digit pin for RF Hub reset.

[@jamesdefrancisco7174]

Can you turn off the seatbelt chime with this? And also I have a cab and chassis model and want to activate all 6 speakers instead of just the 2 door speakers, I read somewhere that this would allow me to make those adjustments?

[@MKSPerformanceOffroad]

I havent seen the exact procedure for activating speakers, I believe it will do it and I know the chime can be turned off. The chime is one of those things that is often done if you cant get it to turn off any other way. There is supposed to be a procedure you can go through that turns it off but it was just easier for me with the program because I already was in it.

[@michaelbattenfield4100]

You don't need this to turn off the seatbelt chime - there is a procedure to turn that off via a key/buckle/unbuckle sequence

[@MKSPerformanceOffroad]

@@michaelbattenfield4100 correct there is a procedure you can follow to turn the seatbelt chime off without this, there have been a few trucks that I have done this procedure without alfaobd where it would not take and it was just easier to use the program. I think its easier to just turn it off while you are already in there anyway.

[@senosk2434]

Yea you can i did on my

[@timdarby5960]

Put key in ignition, switch to on position but don't crank engine. Buckle seat belt and unbuckle it 3 times on the last time leave it buckled in. Turn switch to off position. If you hear a chime it worked correctly.

[@harleysampson4703]

Doesn’t work on iPhone

[@SilveradoXST]

Will AlfaODB program electric fan temp settings and turn off air shutters? 2021 Ram DS classic.

[@MKSPerformanceOffroad]

I honestly haven’t had a chance to mess with the newer trucks 2019+ so I couldn’t tell you for certain.

[@SilveradoXST]

@@MKSPerformanceOffroad The items are ECM/PCM controlled. So the AlfaODB won’t work. It will allow all functions in the body control module to be turned on/off. Best to add LED lights so no errors appear.

[@MKSPerformanceOffroad]

@@SilveradoXST Alfaobd will change bcm config and some diagnostic stuff it is decent at. If you need to get into ECM/PCM you likely need a programmer or j2534 pass thru to access those parameters. Might check into Warp tuning software and a raceme ultra programmer or mm3 programmer. Those would be the more expensive route though to only change those settings.

[@bishopgeorge1333]

I have a 2018 dodge ram 3500 and I want to be able to run my tail lights in LED and also I want to be able to run my head lights with HID's, I have them in now but if I can get rid of the resistors will be great, can you tell me how to get there and do that in the program?

[@MKSPerformanceOffroad]

Yes, if you follow my alpharex headlight programming I explain how to set those to led lights, as for tail lights there are settings you can change but I do not currently have a video on this. Best source of information I can point you to is on cumminsforum.com under alfaobd thread or the ramzforum.com . This is a very popular mod that people do and there is alot if info to guide you. Hope this helps.

[@bishopgeorge1333]

@@MKSPerformanceOffroad Yes sir and thank you I'm on those forums.

[@leonwilliamsiii7942]

Hello, I have a 2014 Ram 1500 2wd. I am wanting to know about the resetting or reprogramming of the abs module.

[@MKSPerformanceOffroad]

What are you looking to accomplish?

[@leonwilliamsiii7942]

@MKSPerformanceOffroad I've owned an obd link for two years just trying to see if the OBD link could reprogram are reset the ABS module .

[@cjbarlow61]

Same here 2017 ram 1500 4x4. Abs module went out so now I have no abs, traction control, trailer brakes, or 4x4

[@davidcandao1]

My friend thanks you very much for your video. Can you make a video tutorial of how to enable the Trailer TPMS on a ram screem with the obdlinkmx+ and alpha obd

[@MKSPerformanceOffroad]

Thanks for your support. What year truck?

[@davidcandao1]

2021 ram 3500 cummins 6.7L

[@davidcandao1]

Will be great a video tutorial of trailer tpms ,I know a lot of people who will follow and appreciate the video I have expended hours looking for something like it and the closest video was yours.

[@tigervxii]

can you use any bluetooth obd2 reader? or do u have to get the zautomotive one?

[@MKSPerformanceOffroad]

You do not have to use the zautomotive one. You can use many different communication modules but the ones recommended are recommended because they have been proven to work the best with no issues

[@tigervxii]

@@MKSPerformanceOffroad thanks for the replay and knowledge

[@bcrawford9072]

I have a 2015 ram 2500 cummins. Can this due a forced regeneration

[@MKSPerformanceOffroad]

Should be able to.

[@theheilious]

Can I used it to flash an OEM remote start on my 2020 RAM 3500 6.4L? I have the new fobs, hood latch and cable on the way. Dealership wants $750 just to flash it and program fobs...

[@MKSPerformanceOffroad]

Yes, absolutely. Ensure you obtain a 4 digit pin to input for the rf hub

[@theheilious]

@@MKSPerformanceOffroad Where will I get the PIN? Will I also need the bypass cable?

[@MKSPerformanceOffroad]

@@theheilious yes you will need the bypass cable. Either the bypass cable that stays installed or the one that connects at the sgm connections. I believe the 2020 has the sgm mounted in an easier location to get to. Obtain your 4 digit pin from dealer parts dept. It is the rf hub 4 digit pin not the 5 digit. It will be good for 24 hours and then a new one will need to be purchased since the code rolls every 24 hrs.

[@theheilious]

@@MKSPerformanceOffroad, I got the installed bypass cable with only 1 CAN buss lead. I am hoping I don't need the second CAN buss lead? Having some trouble getting the MC+ to connect to the app. Android says it's [paired but I never got a chance to input the Pass code in the instructions? it will pair without the code but it won't connect to the app and if I try to reconnect to bluetooth, it gives me a message: " Must connect to an app". I am sorting it bout but of it's obvious to you? Thanks for all your help so far!

[@jonstevens8949]

All you explained was the software and some of what you can do with it. What is actually needed? Data cables? Orher tools? You were very vague for a "101" video.

[@MKSPerformanceOffroad]

You only need an android or windows device like tablet or computer, an obd comms device like an obdlink mx+, and if it is a 2018+ then you will need a security gateway module bypass cable.

[@MKSPerformanceOffroad]

If you look at the other alfaobd videos that is some other stuff you can do with it being the most popular changes being made. The rest of the changes that may interest you may be found on cumminsforum.com under alfaobd success thread or simply searching alfaobd.

[@jonstevens8949]

@@MKSPerformanceOffroad what about the link cable from an EFI Live tuning device? I understand I'll need an unlock cable for my wife's '20 Wrangler, but will a basic cable work for a '17 Ram? Do I need to buy a specific license for every vehicle? Or one app purchase and done? My whole family has FCA vehicles and this has the potential to save us thousands. I just want to make sure I have everything needed before I get the app.

[@MKSPerformanceOffroad]

@@jonstevens8949 the efi live cable is designed to communicate with the ecm not the other modules like bcm etc. You need to have a compatible device like what is listed on alfaobd.com in order to make changes and access the various modules in the vehicle. Basic cable like obdlink EX will work without the sgm bypass on 2017 and older as these vehicles do not have a security gateway module. It is a one app license and will allow you to program any fca vehicles you connect to as long as they fall into the supported years. Hope this helps answer some questions, anything else let me know.

[@beyondupnorth]

Any idea if the elm27 blutooth dongle for the android torque app is compatible with alphaobd?

[@MKSPerformanceOffroad]

Elm27 dongle should work but no guarantee.

[@fathergratwick]

yes it works I used a 7 year old $12 elm 327 it today to program some new keys.

[@robertvazquez1078]

Where do I download the alpha obd app for IOS ? Thank you

[@MKSPerformanceOffroad]

You can’t, this is strictly Android or Windows OS. Does not work with IOS.

[@mbaddog]

Can this unlock gps?

[@MKSPerformanceOffroad]

No, you need to obtain the unlock code from the dealer.

[@jeffhull4060]

An you delete air ride suspension

[@MKSPerformanceOffroad]

You should be able to turn off applicable air ride suspension settings but that is something you will have to do the research on. Im sure there are people who have done it if you look around on the forums.

[@sppb32]

It might be a great app but does not install on newer Android platforms

[@MKSPerformanceOffroad]

Shows that you need android version 4.0.3 and up. Works just fine on my newer android devices and people I know that have downloaded it. What issue are you experiencing specifically.

[@MrSebesta]

I appreciate the information! Can anyone lead me in the direction for the proper/ recommended interface tool? In other words, what pod is best suited to communicate with the vehicle? I drive a 2008 (DR) Ram 2500 6.7l and I have upgraded the radio so I can't use the radio for wireless connection so I need a way to wirelessly tap into the J1850 (OBD2) connector. Any help will be GREATLY appreciated!!

[@MKSPerformanceOffroad]

Great question, there are many modules on the market that will work but the one that is recommended by the software developer for use is the obdlink modules. I have only used obdlink and have been happy with their products. Hope this helps.

[@MrSebesta]

@@MKSPerformanceOffroad Thanks so much!!! Can you please lemme knows if Alfaobd will work on my truck or is it too old?

[@ericstyer2890]

Do you know if it can change TPMS frequencies? I’ve had a low tire light for a minute. Need to pair the aftermarket one that was used or replace with a new OEM one and pair.

[@MKSPerformanceOffroad]

No, the frequency is set and the tpm sensor should be the same frequency as the system reads which I believe is 433mhz

[@ericstyer2890]

@@MKSPerformanceOffroad the tire shop (Discount Tire) threw on a known brand of aftermarket after damaging the OEM sensor that shows a range that would cover 433hz but the truck doesn’t see it. I bought an OEM one before I took it to them but they didn’t get that memo and used one of theirs. Since then I tried to assign the TRW sensor to the missing wheel on TPMS but it’s not installed so therefore no pressure or spinning motion for the RF-Hub to see active data. Not sure how the RF Hub knows tire position if it’s not programmed, Alfa allows one to assign a sensor and I thought when they replace sensors there’s and activation procedure that helps TPM relearn position but some forums indicate it’s all automatic and senses itself. So far that’s not been my experience. Not only am I missing one on dash but they do not match actual positions.

[@richardpreston6078]

1) will this program and recalibrate the turbo charger actuator? 2) will this do a manual dpf regeneration?

[@MKSPerformanceOffroad]

Yes it should, I have not had to perform the regen though but I know it is an option in the program

[@2LegitTwoQuit]

My I put my LED headlights and my lightbulb (H11) kept turning off after 10 mix max will this fix it

[@MKSPerformanceOffroad]

Which light housing do you have?

[@2LegitTwoQuit]

@@MKSPerformanceOffroad stock. I bought canbus resistors you think they’ll work?

[@MKSPerformanceOffroad]

@@2LegitTwoQuit ok so you have led bulbs in the stock housings. Did you change the settings to HID in alfaobd? What brand of bulb

[@2LegitTwoQuit]

@@MKSPerformanceOffroad they are Sylvania bulbs and no my obd didn’t want to connect to the ecu

[@MKSPerformanceOffroad]

@@2LegitTwoQuit You will need to connect to the bcm and enable the HID setting in order to disable PWM (pulse width modulation) which alternates voltage to the Halogen bulbs to prolong the life of them. This isn’t need with the LED bulbs and tends to cause issues.

[@WHITETAIL215]

Will this work with any bluetooth ODB module

[@MKSPerformanceOffroad]

Dylan .M It should but your capability may be limited with the ability of the BT module you have.

[@dustinmello5715]

Can you do a force regeneration on the ecodiesels and Cummins pickups? Also, laptop vs tablet, can both do the same amount of work or does one do more than the other? Thanks.

[@MKSPerformanceOffroad]

I don’t see a stationary desoot for the ecodiesel but definitely for the cummins. Might be worth a search on the forums. I’d say they can do the same work but computer is better from what I have seen at programming mileage and hour correction. I do like the tablet for quick stuff though.

[@gobluekurt]

This is what I want to know

[@mastermoarman]

What info does it give for the cummins?

[@patvirgin8822]

Does the data link need to stay plugged into the OBD port all the time? or just while making adjustments? if all the time to you have a preference on the type/brand of OBD port splitter cable? I have a 2017 Ram 1500 EcoDiesel.

[@MKSPerformanceOffroad]

Only while making adjustments.

[@jacobsebastien3910]

Can the obd 2 mx+ show transmission temperature in a Ram?

[@MKSPerformanceOffroad]

I think it will but I dont recall off the top of my head. I know I have been able to read alot of different things but I dont remember if trans temp was one of them.

[@markjohnson8726]

You can get your pin number using the alfaobd you don't need the dealer

[@MKSPerformanceOffroad]

Alfaobd doesn’t work to pull pin on all years and you will need the dealer or pin puller.

[@markjohnson8726]

@@MKSPerformanceOffroad it work on my ram 2500 2014.

[@MKSPerformanceOffroad]

@@markjohnson8726 yessir some model years it will and some it won’t. It does not work on my 18’ and 19+ the pin rolls every 24hr.

[@MKSPerformanceOffroad]

Not sure if alfaobd had an update but I was able to pull pin now whereas before it would not.

[@AB-mg8zs]

@MKS Performance & Offroad great video, thanks for the info. I got a question. I can't find any info if this alfaobd program will recalibrate my tpms in my 2016 ram dually. After doing a rotation they tire positions are off now. Will this program allow me to recalibrate tpms position? I have already put 100 miles on them and they have not reset. Thanks

[@MKSPerformanceOffroad]

They should reset on their own, if Im not mistaken you need to drive over 55mph+ for 15-20 min.

[@MrSebesta]

@@MKSPerformanceOffroad that is correct with the exception of, "needs to be above 25mph"

[@akrider174]

Can this be used with a race me ultra installed with the unlock cable that’s with that? Just need to know how to hook up MX+ with um this already installed?

[@MKSPerformanceOffroad]

Are you referring to the RSA unlock cable that unlocks the ECM?

[@akrider174]

@@MKSPerformanceOffroad well my race me comes with an unlock cable for tuning purposes. Do I not need one to do a relearn with the alpha obd software?

[@MKSPerformanceOffroad]

@@akrider174 what year truck? You will need the sgm bypass in order to even talk to the modules in the truck

[@akrider174]

@@MKSPerformanceOffroad 2016 cummins 6.7

[@akrider174]

Found on alpha site only needed for 2018 and above 👍

[@larryheywood1844]

I have a 2018 2500 I have the bypass module my question is can you keep the bypass on indefinitely or do you just use it to make changes and unhook and go back to the original obd port??

[@MKSPerformanceOffroad]

Depends on the type of bypass you have, if its the one that plugs in under the dash from obd port to can bus blocks then you can leave it in as long as you want. If it is the one you plug in behind the radio that requires you to remove your radio than no, it needs to be plugged in for each change. Hope this helps.

[@larryheywood1844]

@@MKSPerformanceOffroad thanks it's the one that connects behind the obd port KAODTECK

[@MKSPerformanceOffroad]

@@larryheywood1844 the Kaod tech is the one I have and can stay installed

[@blakkatsound]

does the car ecm need to be unlocked?

[@MKSPerformanceOffroad]

What are you wanting to accomplish?

[@blakkatsound]

@@MKSPerformanceOffroad thank you for the reply, I am wanting to re-initialize an ABS Module that I replaced from a salvage yard. Love your channel and have learned alot. Thank you for help.

[@MKSPerformanceOffroad]

@@blakkatsound you should be able to initialize it, what year is the vehicle? Head over to IG and give us a follow, we got more coming.

[@blakkatsound]

@@MKSPerformanceOffroad the vehicle is a 2021 Dodge Charger SRT8 Scat Pack, the Abs module went bad so I replaced it with a working one from the salvage yard and just wanting to turn off the ABS light (it's annoying) Once again, thank you for your reply and I def will go over to IG and follow

[@MKSPerformanceOffroad]

@@blakkatsound you will likely have an issue without a sgm bypass like we do on the ram trucks 2018 and newer. You likely wont be able to do anything without bypassing your security gateway module.

[@pelayo620]

Do I need the pin to change the vin..?

[@MKSPerformanceOffroad]

I don’t have any experience with this personally so I honestly dont know. I would ask on the cumminsforum in the alfaobd success thread and someone will know.

[@denismitchell6922]

In the settings what interface connect do you use for the OBDlink mx+

[@MKSPerformanceOffroad]

It should be listed in that section.

[@christhelen3783]

Will this work with 2019 Ram

[@MKSPerformanceOffroad]

Chris Thelen yes it should, I have heard of guys making changes on the 19’s already with it but it might be limited.

[@keithlucking7320]

Can you add fog light option with it on 2018 Tradesman

[@danielkannady8397]

I’d like to know this too.

[@MKSPerformanceOffroad]

Yes you will be able to see pretty much all options that can be added and just need to tell the truck it has them now.

[@SuuuperBurch]

The fog lights are direct, they dont go through tipm

[@philthis68]

Will this let you program the ABS Module replacement ?

[@MKSPerformanceOffroad]

If your talking about programming the factory program then no, you would need a j2534 passthrough device and access to mopar program file to reflash.

[@philthis68]

@@MKSPerformanceOffroad thanks for the quick reply

[@johnstark3058]

Will the alpha obd let me enter injector quantity codes into the ecm?

[@MKSPerformanceOffroad]

I do believe it is an option, are you referring to the trim codes for installing new injectors?

[@johnstark3058]

@@MKSPerformanceOffroad yes trim codes....I was told it's not an option on 2013 through 2016 , those models are vin specific, meaning the injector codes are not put in for those years as long as you buy the vin specific injector for your year truck, that info. Came directly from Alfa obd tech support

[@MKSPerformanceOffroad]

@@johnstark3058 have you looked on ramforumz.com or cumminsforum.com and seen if anyone has successfully done this? I cant say I have because I havent performed this function with alfaobd. I know I saw several people who were able to do this in ecodiesels.

[@johnstark3058]

@@MKSPerformanceOffroad can't be done on Alfaobd for my year model, there is no option in the drop down menu...not to mention AlfaObd has said the same thing, option is not provided because it's not needed so Long as you buy the correct injector

[@MKSPerformanceOffroad]

@@johnstark3058 I didnt think it was needed on the cummins as you said with buying the correct injector. Ive done trim codes for bugger stuff but never these engines. Were you trying to figure out if it was needed or did you have instructions telling you to do this?

[@quatruckin5548]

Will this correct mileage I’ve done a cluster swap in my charger and the new Cluster miles aren’t even close to correct

[@MKSPerformanceOffroad]

Yes it will.

[@quatruckin5548]

@@MKSPerformanceOffroad great I just ordered mines from Amazon

[@leonwilliamsiii7942]

Yes it would definitely change your mileage

[@selvindeleon498]

Can you program the removal of the def system with this?

[@MKSPerformanceOffroad]

No sir, those parameters are found in the engine ecm and would need other software to access them.

[@joe7528]

2015+ the ecm is locked you can't make any changes to the ecm however you can buy an unlocked ecm and have it programmed

[@kylewiese8354]

Can you add the oem remot start and add the sals code with this or am i still going to have to take it to the dealer

[@MKSPerformanceOffroad]

Kyle Wiese you should be able to, here is a writeup on it. www.ramforum.com/threads/how-to-add-remote-start-to-2017-ram.99849/

[@johnherrington3416]

Fyi. Still will not be able to use remote start with uconnect app. Even tho FCA will have you download and update the newest 8.16.xx version for(must use a specific brand thumb drive only kingston fyi) infotainment system as they said this would allow me to use remote start function from phone app. After pulling teeth. Found out unless your vehicle was produce from the factory with the remote start option. The dealer install remote will not be an option via the phone app. Unless someone comes out with app outside of Uconnect. 2017 2500 6.7l 44,xxx miles= New gear box, rear diff, front inner drag link(cannot replace as the morons welded via recall even after i declined and document on paper and service manager telling them not to.) 6 months at dealer so far. Various other recalls, switch here, door handle here. Oh yeah I have the hepres of Ram the service electronic brake system warning that cycle and flares up when it wants but never for the dealer. Damn rash i mean my Ram has been in 3 Ram dealerships various FCA complaints. Yeah I am a Chevy guy. You think i learned my lesson 🤔?

[@mirkomarta6762]

Do I need the security module to activate bed lights I installed on 2021 ram 1500?

[@MKSPerformanceOffroad]

You will need to bypass the security gateway module on any truck after 2017 in order to communicate with this tool

[@gieziaguillon1730]

Can this be use to add keyless entry ?

[@MKSPerformanceOffroad]

Yes, it is possible to add keyless entry with alfaobd

[@gieziaguillon1730]

@@MKSPerformanceOffroad okay thank you for the reply because I’m deciding between taking it to the dealership or just doing it with alfaobd

[@MKSPerformanceOffroad]

@@gieziaguillon1730 do it with alfaobd, lots more to do if you ever want down the road

[@gieziaguillon1730]

@@MKSPerformanceOffroad yeah I’ll probably go with that thanks for the feedback

[@krhofbauer]

So is it just the windows program then? Saw you had an OBDlink MX but didn’t touch on it. I’m looking at doing an air ride delete on my 17 Rebel (to King coilovers) and I’ve read this will disable air ride and turn the truck to standard coil configuration

[@MKSPerformanceOffroad]

This program will do much more than just a windows program and should be capable of configuring your truck without air ride.

[@tundrabear9663]

🎉

[@gregwillet2727]

Quick question, I have a 2014 2500 ram. The dash lights (evic) and the radio lights are not dimmable when the lights are turned off. Can the Alfa obd fix this? The lights are dimmable while in the Auto, parking lights and headlight position. Any feedback is appreciated.

[@MKSPerformanceOffroad]

Honestly haven’t ever come across the need for this myself. I would say that if its not an option in the bcm then it wouldnt be possible but I honestly dont know. Best place to ask would be on the alfaobd success thread on Alfa OBD Success! r.tapatalk.com/shareLink/topic?share_fid=13656&share_tid=2490261&url=https%3A%2F%2Fwww%2Ecumminsforum%2Ecom%2Fforum%2Fshowthread%2Ephp%3Ft%3D2490261&share_type=t&link_source=app

[@kc03300]

will it work on a 2004 ram 2500 cumin. I need to set up my daytime running lights

[@MKSPerformanceOffroad]

kevin c I cant confirm whether or not it will as I have not used it on that MY yet. It is listing on alfaobd.com MY 05-18 but I would suspect that if it has the same modules as an 05 it may work. Your best bet is to check out the alfaobd threads for 3rd Gens on cumminsforum, dodgeramforum, etc.

[@spydersquadatl1980]

@@MKSPerformanceOffroad hey I got a 2017 ram I alfaobd app and obdlink mx+ trying to get my turn signals lights to work on my tow mirrors but can't figure out how to do it

[@MKSPerformanceOffroad]

@@spydersquadatl1980 try this procedure.. www.cumminsforum.com/threads/adding-towing-mirrors-and-alfaobd.2497503/