I've maidened the RSX380! Took it for a short run in the Hot Pond, the lake is still frozen...
Пікірлер: 31
@gerardscheffer88484 жыл бұрын
Beautiful boat man!
@BWWGL95 жыл бұрын
By the time you get that TUNED, she should be in the mid-70's. What are you using for ELECTRONICS & MOTOR ?
@marksrctime83312 жыл бұрын
Did you buy the hatch hold downs ??? and where did you buy them ???
@chilly72612 жыл бұрын
Yes. I bought them from offshoreelectrics.com
@marksrctime83312 жыл бұрын
@@chilly7261 Thank you very much
@chilly72612 жыл бұрын
@@marksrctime8331 👍
@bdanielcal46082 жыл бұрын
Hey sam how wide is the hull there's a lack of 45 and up riggers except gas out there you think a 45 nitro wood fit comfy in there I emailed Mike but don't want to bother him thanks
@chilly72612 жыл бұрын
It's 4-1/4" outside measurement, with 1/8" walls. So it measures 4" on the inside. It measures 3" at the highest point, not counting the canopy...
@bdanielcal46082 жыл бұрын
@@chilly7261 so 4 inch mounts will Work cool thanks for getting back asap
@StrBADCyperIgwt2 жыл бұрын
All fine until the fishing line wraps up in the prop 🥴
@jjrotogeek5 жыл бұрын
Very cool brother. 🤘🤘🤘 need to get out and do come maidens maself
@chilly72615 жыл бұрын
Thank you. So you did some new builds this winter? It's still early weather wise...
@jjrotogeek5 жыл бұрын
Sam Hallstrom yes. I’ve built 2 riggers and a couple hydros. Weather is perking up now, so no excuses!!! I’ve done some build overviews of the boats on my channel. Where ya from
@jjrotogeek5 жыл бұрын
Sam Hallstrom ahhhh Nevermind!!! Didn’t realize u were the ul19 hacker in Wisconsin lol. I’m from northern indiana originally. Your rigger looks great
@chilly72615 жыл бұрын
Haha! Yeah, I'm that guy. The fraud. Your ice should be out I suppose. Time to get them wet...
@jjrotogeek5 жыл бұрын
Sam Hallstrom lol the fraud. Don’t think so. I think you’ve done a hell of a job on that ul19 project. Beats scrapping the hull. Trust me, I’ve done my fair share of odd mods
@SelenaI.4 жыл бұрын
what are the cables taped to sponson tubes?
@chilly72614 жыл бұрын
Safety cables to keep the sponsons attached to the hull in case I break a carbon fiber boom tube. The hull would sink without the sponsons attached.
@arnoldchildress80533 жыл бұрын
Nice looking boat and all but it's too damn cold
@chilly72613 жыл бұрын
Thanks. You're telling me? Haha! Agree 100%...
@noeltampos17864 жыл бұрын
What is the diameter of boat ? Thanks
@chilly72614 жыл бұрын
Length is 38 inches from the sponson tips to the transom. Width to the outside of the sponsons is 24 inches...
@noeltampos17864 жыл бұрын
How about the body of the boat ? Thanks again
@chilly72614 жыл бұрын
Not a problem at all. The tub is 36 inches long and 4-1/4 inches wide.
@RBAERO3 жыл бұрын
Nice. What eletronics you using in the RSX380?
@chilly72613 жыл бұрын
Spektrum SR6000T receiver, Savox SA-1231DG rudder servo, Leopard 4092/1390KV motor, ZTW Seal 200 amp ESC running on two 4S Optipower 4000 mAh lipos in series, so it's an 8S setup...
@edwincordero85 жыл бұрын
I am really happy for your success. Too much epoxy, glue, wood sanding and fine measurements were worth it. Now your fine speed tunings come next for those 60mph's. Congrats.
@chilly72615 жыл бұрын
Thank you very much. It was very enjoyable to build. And rewarding to run it for the first time. I have a lot of tuning and learning about a rigger in front of me. That was a bit sketchy doing the maiden run in that Hot Pond for a couple of reasons. One being I wasn't going in the water to recover it. I also didn't want to run it onto the ice...Cheers!