Stanley Camp Cook Set sale!: amzn.to/2yoo1LP Utensil Holder Stove here: amzn.to/2AgevLy Shop Our Amazon Store: www.amazon.com/shop/iridium242 Stock up on your long term food storage here! www.thrivelife.com/iridium242
Пікірлер: 381
@Iridium242 Жыл бұрын
Be prepared with emergency antibiotics prescribed to you from a licensed doctor in the USA Get your JASE Case today jasemedical.com/?rstr=4460 and use my 10 Dollar Discount Code For Jase: IRIDIUM10
@mickcary83514 жыл бұрын
Add a P38 can opener to the key ting on the lid! Then you always have a can opener and it stays a little cooler than the key ring making the lid easier to pick up.
@crazysquirrel94252 жыл бұрын
I hadn't thought of that. Thank you for the tip!
@pure69hatred2 жыл бұрын
Great tip! Thanks!
@scottlindholm556810 ай бұрын
If just using a key ring lock it vertical it will stay cooler and Walmart currently sells a anodized aluminum cup with markings
@Aikidoman065 жыл бұрын
I did something like this with my Army canteen cups. I put ice water in a container, measured a cup and poured it in. In a few minutes you could see a condensation line. I marked it with a sharpie marker. I added another cup and so on until I reached the top. I use a nail punch to put a small dent on each Mark. Thirty years later my son used the as a boyscout.
@sojourn15444 жыл бұрын
That's being smarter than the cup....lol....but that is really awesome......
@bobketterer91194 жыл бұрын
Back in Boy Scouts we all carried old army cups. We used an engraving tool to make a mark on the inside.
@nx992 жыл бұрын
I used a long pair of shop tweezers over the rim of the cup. Marked the spot on the outside when the inside touched water.
@SALTYCOMBATDIVER-ExInstructor Жыл бұрын
@@bobketterer9119 little did I realize how important it was but our boy scout troops were ran by active duty service members (one of the perks of being a dependent). We were essentially sponsored by the military from camp gear to C rations and MREs. I later realized that we got early basic training and professional survival training. We also played a lot of capture the flag, just like infantry units.
@SALTYCOMBATDIVER-ExInstructor Жыл бұрын
An interesting technique to help prevent deformation of the metal while creating the indentations is you can fill it with water and freeze the water after making where to make the indentations. The frozen water will help support the shape of the metal while pounding on it to create the indentations.
@WH6FQE2 жыл бұрын
I have been using this Stanley set as well as the larger set that includes the bowls and I have never melted the plastic tabs on the lids of either of them. I camp or backpack with them at least once or twice a week. Wait, that handle on the Stanley is made for hanging on a tripod. Once the lid is placed on the pot, close the handle over the top and the slider bar on the handle is where you attach it to the chain from the tripod so that it hangs level.
@MrOksoldier202 жыл бұрын
I never knew that!
@WH6FQE2 жыл бұрын
@@MrOksoldier20 that was one of the tricks that Stanley built into that kit that I love.
@mariatorres9789 Жыл бұрын
I literally melted that stupid green plastic, the first time I used the Stanley, a couple months ago. I was pretty ticked. Why wouldn't they just put silicone?
@southernmedicine19875 жыл бұрын
I used a small gauge dog choker coller and some small "S" hooks for the pot hanger. You can place it inside the pot for storage and it wont slide on the handle to a corner.
@robertgullickson87584 жыл бұрын
Great upgrades. I also appreciate your not wasting time with the obvious steps as you go along. Some things can easily be done off camera. We can imagine what you’ve done. Great job with this video. Thank you
@alexanderweaver91825 жыл бұрын
Great mods on this great kit and for the price it can't be beat. I have this same kit and I love it. I bought two UZO lids from Amazon and the lift rings actually stay upright. I love the bail mod to hang the pot on a tripod. I bought a titanium 450ml cup with lid and it nests well with the Stanley pot.
@raymondlambert41325 жыл бұрын
You just saved me about $80 and a ton of space in my Get Home Bag... you are The Man!
@KaylynnStrain6 жыл бұрын
I did the same thing with both Stanley cooksets I own, I used a saw to cut the plastic then I popped the pin out before putting the split rings on the lids, makes it easier to list the lid with a pointed stick or other utensil
@strongbear93044 жыл бұрын
Thanks for the modification ideas. I actually had purchased 6 of these two week ago and was trying to figure out how to modify them for my wants and needs. That did the trick with a few "adjustments" for me. First time I tried using it after the modification the wire bail slid over to one end spilling a bit, easy fix in the center of the bail I just a small upwards arch . Excellent Presentation and a New subscriber!
@Tripsolo654 жыл бұрын
You know, I always hate to be "That Guy" because nobody wants to be "That Guy", but, did you happen to notice the marks you made on the tape almost corresponded directly with the wire handles where they attached to the cup? You did say if they weren't exact it wasn't the end of the world, even though that is what you're prepping for LOL.... NONETHELESS, your cook set is extremely BADASS!!! Thanks for taking the time to help others. It's people like you that the world needs more of.
@bnicholas19013 жыл бұрын
Rock On Rick... Rock on.
@jam74534 жыл бұрын
It’s great to see other people using ingenuity to upgrade something with mods & repurpose other things especially in this manner. Keep up the awesome videos!
@georgespencer7184 жыл бұрын
Iridium, after watching your modifications to your cook set, you’re right on. The only thing that I would add to the cook set lid idea is to place a small wooden stick into the ring and just leave it while cooking. When you want to lift the ring... just raise the ring with the stick. Just a thought.
@georgespencer7184 жыл бұрын
Oh, and I thought of something else: if you put the two holes for the bail, put one hole in where the handle sets and the next one of course on the opposite side, instead of 90* to the handle connection. That might allow you to keep the cook pot level and still allow the handle to be used to help lift the bail and pot from the pot support. Just a thought!
@Pygar26 жыл бұрын
Great ideas! Now add a jog to the bail's center for hanging purposes!
@norsefalconer5 жыл бұрын
Great mod vid, thanks for sharing. I use a thin cozy (it was free with a Bike Bandit order) on the bottom of the Stanley when I store it with the Ozark cup. This keeps any soot from getting on/in the cup and keeps everything from rattling.
@casualpreparedness23476 жыл бұрын
Good idea. I used a Dremel tool to scratch the level marks on the small cups. I have two sets of those you have for demonstration too. I might modify the Stanley cup the same way to hang up on the tripod. Excellent video. 😎
@lauradesouza53715 жыл бұрын
Awesome stove I love the simplicity and functionality.
@lordfairfaxpreparedness5 жыл бұрын
Awesome Ideas! I used a a little thicker key ring also on my Stanley kit and it stands up just fine. Haven't done the holes for the wire/bail system yet, mostly cooked over coals thus far. Will do something similar with fish mouth opener.
@glennslatoniii49313 жыл бұрын
Great video! On the key chain ring mod- before I put the top on, I thread the key ring a little bit forward so it stands up. Never had an issue with heat, but on a campfire, the ring will be up so you can put a stick or something through it to lift the lid.
@kentcostello80995 жыл бұрын
Thank you for the info. I got 2 Stanley cup sets in my back pack. I'm going to do that to them .
@titanpreparedness5 жыл бұрын
Bit late but great mods. The key ring is my favorite mod. Put the lid on and lock it, hang it from the ring great idea for over a fire. Still the best kit for a perfect price.
@DLWhite-D681355 жыл бұрын
Good video! Thanks for the insights! I did mine with an electric engraving tool. Less likely to damage the cup.
@bruceforster37094 жыл бұрын
This is brilliant! And I love the simplicity of it!
@markfillery10025 жыл бұрын
here is a tip when bending your hanger use a pipe or round wood to put a round bend in the middle it stops the pot from sliding when hanging
@viewsandreviews1804 жыл бұрын
Good video. I like the way you modified the cook pot. I got mine to hang well by adding a short piece of TIG wire that hooks under the lip and on the handle (no holes)
@Antonio-ye1jv4 жыл бұрын
Wow! Thought about buying BOTH items each time I go to walmart. This time I will purchase both. Good ideas. Tks for posting n sharing.
@daveboyce72355 жыл бұрын
Nice video, good ideas. I cook with the plastic tab on the lid all the time and it doesn’t melt, even when it’s used on the steel cup. I cook on hot coals and a stove and never melted, However I don’t place coals on the lid as used for baking so your ring would do well with that. The hang wire is a good idea. I think I’ll just make a wire wrap around and one side will come up at the handle so the handle balance will not be a problem. That way I can use the handle along with the wire hang to help in pouring or holding.
@bereantrb5 жыл бұрын
Good, simple bail mod. I think the only thing I’d do different is rotate the holes 90°. That way I can still use the folding handle and comfortably pour to the side without dribbling out the holes. Thanks for the tip.
@dubb85106 жыл бұрын
Get the Magellan titanium spork from academy it has a hook at the end that’s good for grabbing the key ring when it’s hot
@manonarcand21465 жыл бұрын
Have spare silverware strainers bought for my camping silverware but had a more usueful idea to me. Now i ll make stove for my kids campers. Thx for great idea :)
@kisbushcraftdownunder4 жыл бұрын
I made a measuring dip stick using the handle of my spoon and a center punch regards mike
@tomslikk21305 жыл бұрын
If you adjust the hanger handle length you can use it to secure the nested SS cup to the bottom.
@thomaspigg3064 жыл бұрын
I've had the same kind of set-up that you do (for probably the last ten years), and the only difference between mine and yours is when I made my bail handle, I used stainless steel welding rod and I bent mine in such a way that it goes completely around to the bottom of the (tall) cook cup. I'm glad to see someone else do this, cause I don't know how to video, transfer, or edit anything. Thanks for the video!!!
@unclestabby40184 жыл бұрын
Great video. Thanks from a guy that loves camping/ survival but has no money.
@robertthurman6734 жыл бұрын
I put a paper towel around the bottom of the Stanley pot and then slide it all into the cup. This keeps it from rattling and gives you a paper towel to use as needed.
@AshamedTripod24 жыл бұрын
That's what I've been doing. Hate the sound of the metal scraping
@shihanjulio5 жыл бұрын
Hint: when drilling metal, use firm pressure and low rpm's and a little oil. High speed only heats and lessens the temper on the drill bit. Great video.
@SuperSuperdude884 жыл бұрын
cool idea! i did a similar thing but i used what i call " C " clamps. Like large C shaped Vise Grips, and they dented the inside and out. was very easy and done in 1 second.
@peterevans81945 жыл бұрын
Great video...Another way to make a good detachable bail is to use a length of stainless steel cable with a small croc clip on each end....
@thomascronquist16045 жыл бұрын
I like your mod on the lid. I removed the plastic with a punch.I used a mental rod to bend and create a larger Handel that fits in the hole, and stays up and looks like a L Thanks for the idea.
@BillHalliwell4 жыл бұрын
G'day Iridium, Thank you so much for this brilliant video. A great exercise in problem solving and money saving. My first Stanley Cook Cup had its handle melt off after about the third or fourth use. That was a few years back. I got to tell you that great minds think alike. I too, used a key ring, but one of those flat kinds that open up when you press down on the opposite side. (no fingernails needed) I forget the brand name. In any case it solved the problem on my next Stanley cup. I had to get another one because, apart from the handle, it is a great piece of design and really compact. I'll be incorporating your mods on my Stanley and my, larger, metal drinking/cooking mug. Thanks too, for your brilliant idea for the cutlery holder stove conversion. Like all great ideas, it's so simple! We just happen to have a cutlery holder that's almost the same. We'll give it a go. Cheers, BH Hobart TAS
@MarkRuslinzski3 жыл бұрын
You sir have a Great mind for this stufff, its nicer now than what it originally was
@JohnSmith-vb6jx3 жыл бұрын
With the key ring installed on the lid you can just fold the handle over the lid and lock it in place with the key ring sticking up, loop a cord through it and suspend it from a tripod. A light chain with a hook will work too but I like using a loop of #36 bank line going up to an adjustable toggle. No drilling and bail handle required or removing the handle for balance. Works great.
@ronr.534005 жыл бұрын
more detail, to better do it myself, thanks ... see, i already did the hanging line, and i have the cup, loved the utensil strainer stove
@ljaysperspective17754 жыл бұрын
I think that these are good ideas and will aid in accuracy and facilitate food prep. Regarding the cup, I would prabably use a dremmel with a sanding wheel and score the marks in. Thx for sharinf
@black-end98764 жыл бұрын
Hello, I have seen her video! Thank you for showing me. I noticed that they drill 2 holes for their pot hanger. it is to recommend the 2 holes to turn 90 degrees further so nothing can run out of holes. or you buy yourself a mug of pathfinder. this is already done so they have to tinker before.
@journeybrook93575 ай бұрын
Your system looks great. I added my heat diffuser I already had to the silverware stove ( great ideal 👍)Using a stainless steel plummer chain wrapped works great for hanging. But I digress for I just don't want to drill holes in my beautiful Stanley cook set.
@jeffreycoulter40954 жыл бұрын
I put a bend in the center of my bail to suspend it better. I added a scrub pad, 2 shop towels or old wash towels, a sterno, knife fork and spoon, small container of dawn soap. All fits inside kit.
@rocktroll20026 жыл бұрын
If you don't want the ring to get hot you can partially slide the metal of the lid into the ring and it Will stand up by itself and not get hot. And a fisherman's jaw opener will work with the holes and the lid will work with it if you put two slots in the lid. It's an awesome little kit we use ours all the time.
@DesignsbyDonBrown3 жыл бұрын
I also found a spice set that sits perfect inside the cups, in that Stanley pot.
@SPCLPONY3 жыл бұрын
Where did you get your spice kit?
@davebriggs15893 жыл бұрын
Me too gsi I believe it is
@chucksexton19852 жыл бұрын
You could use high temp rtv silicone for the key ring to help with heat resistance. I'd suggest exhaust silicone which is red.
@jackwhitt28014 жыл бұрын
I liked the idea of the silverware drainer stove.
@waynethebarber10953 жыл бұрын
It can also fit in the the 25 oz Pathfinder too. Bigger cup and better handles too.
@NitrousDiecast4 жыл бұрын
For the wire, i would add a little divet in the middle, so it doesnt slide when hanging off a branch
@skunkfox4 жыл бұрын
use a center punch on the Stanley set first. Helps keep the drill bit from wandering about on you. Don't forget to debur the holes and wire hanger to remove the sharp edges. Use a Dremel debur tool for this.
@timothyedmiston87565 жыл бұрын
Nice use of the bail,I would just leave it hooked on it ,looks great
@jamesfishfish90995 жыл бұрын
I use that small Stanley pot for my coffee French press and the cup I Have has the measuring lines
@k5hoho5 жыл бұрын
No holes in your Stanley hack! Instead of drilling holes (I did it and wasn’t happy), you can use a 3 foot length of lite chain (1/8 inch) to wrap around the Stanley below the handle. You can easily hang the Stanley. I carry a 3 foot and an 18 inch section of chains with hooks at the ends. The longer chain wraps around the Stanley and the short chain wraps around 3 pieces of wood to make a tripod over the fire.
@David-mu5rv5 жыл бұрын
Do you have a pic of that mod?
@k5hoho5 жыл бұрын
Yes. Got to figure out how to post it. The chain has “S” hooks at the ends. Wrap the 3ft section around the pot, connect the s hook to the chain to form a circle. Then connect the other end S hook to the other side of the pot. This will create a loop above the pot. I use the 18” section of chain to hook the loop holding the pot to a 3 leg pot stand above the flames.
@smendoza72365 жыл бұрын
Sounds smart, please post image.
@shaneintegra4 жыл бұрын
I can't picture exactly what your talking about lol
@TinyIslandMaine4 жыл бұрын
0m3n a video would be cool if you have the time 👍
@stevenperron36193 жыл бұрын
I use a Snowpeak with no cup markings. I measured the water, like you, but "notched" my titanium spoon at the cup, cup and a half, two cup depths. I just stick it in the water to tell how much I have. But I like your method, too.
@lordofgraphite3 жыл бұрын
This video has fixed every issue I had with the Stanley pot
@jimpoulalion69052 жыл бұрын
Great Video! I used a tape measure to transpose the 1, 1.25 and 1.5 cup marks outside
@daniellow426 Жыл бұрын
the Walmart silicon folding cup makes a good lid for either one of these, it measures your food and liquids too. When it is flattened it fits snugly onto your 3 cup and its folds allows steam to drip back into the cup, it even expands a little instead of boiling over. Cooler to the touch than a metal lid.
@Pooch19535 жыл бұрын
One suggestion, on the coat hanger bail handle you made for hanging, you will find you have to play around with balancing it when hanging, one way to beat that is to put a small kink, dead center on the top part where it hangs. Think small upside down letter "U", this way you have it center balanced when hung from a chain, bar, or other method, without the sliding from one side or the other.
@Iridium2425 жыл бұрын
Thanks, a few weeks ago someone suggested that, so I gave it a try and it works great.
@hawkdriver685 жыл бұрын
@@Iridium242 Better yet, just make a triangle instead of the rectangle and "jog". easy peasy. ; ) Also, instead of perpendicular or parallel with the handle, drill the holes 45 degrees offset. that way you can still use for pouring, AND you can rest the wire bail on the handle so it doesn't hang into the fire or coals. (which way you offset the holes would depend what handed you are for most comfort. : )
@mesquiteguy1215 жыл бұрын
VERY Nice. I have the Stanley. Need to buy the other item. Thanks for the ideas and the video.
@bob_btw6751 Жыл бұрын
Use a spring clamp wooden clothes pin to pick up the ring on the lid. My folks used that on Mirro cookware aluminum pot lids when I was a kid.
@hawkdriver685 жыл бұрын
Just make a triangle instead of the rectangle and "jog". easy peasy. ; ) Also, instead of perpendicular or parallel with the handle, drill the holes 45 degrees offset. That way you can still use for pouring, AND you can rest the wire bail on the handle so it doesn't hang into the fire or coals. (which way you offset the holes would depend what handed you are for most comfort. : )
@oldtimerlee88204 жыл бұрын
Triangle is a good alternative. Agree with orientation of the holes. Front to back --- in line with the handle, rather than side to side. I don't want to drizzle coffee down my chin, if my lips miss covering the hole. :-) Plus, you don't have to take the handle off. Simple close the hanle, with or without the lid, to help balance pot over the fire. BTW, a bend the center of the coat hanger handle a bit, to help the pot stay centered when hanging on a cord. something like this .......^........
@moto.kitten5 жыл бұрын
Great video thanks, I’ll use your technique to mark my cup. And another great way to suspend your pot, for people that don’t want to drill holes, keep the lid on and put the handle in it’s locked/closed possession. And using the key ring and some wire to hang from a tripod
@ScorpionRegent4 жыл бұрын
That great, ... if you want a steam explosion. Even pressure cookers have a blow off valve. Don't get me wrong blowing things up can be considered a hobby and it's all good fun until somebody gets hurt.
@MrZombeeBait4 жыл бұрын
@@ScorpionRegent um... It has like 7 or 8 holes in the lid... Lots of ventilation
@robertmiller26292 жыл бұрын
I like this mod and if you open the handle slightly you can add a center bend in the top of the handle so that it will hang on center from a tripod hanging system so that it will not slide while a full boil like square top handles have a habit of doing. Keep up the good work and hope to see more of things on your chanel
@earlelzy72433 жыл бұрын
I saw a hack using a niteyez carabineer#2 to replace the lid handle.
@jasonb47387 ай бұрын
Little tip on the lid tab. The pin will push out easy and you don’t have to cut it and risk damaging the loop. If you do damage the loop, a small eyebolt can go back in place.
@williammccaslin85274 жыл бұрын
It'll work an no damage, all good. For 5 bucks hard deal to beat, the keychain mod is gtg, the bail is also gtg when you make it out of brass coat hanger
@MrPatrick77775 жыл бұрын
Thanks. All good mods.
@leojoseph63854 жыл бұрын
Great DIY Modifications!
@bigbuck7623 жыл бұрын
I made a video a few years ago on the modifications that I made to the Stanley cook pot I took the plastic piece off put a key ring on there and I open the key ring and slide it back just a little bit so that way It will stand up I also got a fish mouth spreader drilled two little holes like you did and I also put a couple a slits in the lid so that way you could use it with the lid on while you’re cooking
@meanpicker5 жыл бұрын
Love that little strainer stove idea, never seen that!
@oldtimerlee88204 жыл бұрын
Google IKEA utensil strainer stove. Lots of variations on how to build one. I have mine setup to use wood, alcohol burner and solid fuel tabs. Using 4 metal tent stakes allows positioning of the Stanly cup and an alcohol burner exactly where you want them. A tin can lid, (use safety side cutter can opener) can substitute for the alcohol burner. Place the lid where the alcohol burner would sit. Then put a solid fuel cube on the lid. BTW, Walmart sells a version of this same style utensil strainer. It's in the kitchen stuff section of the store. Metal tent stakes in the camping section. Buy a can of green beans to get the can lid. In closing, love the multi-function capability of this strainer stove. Kept in a draw string bag, along with stakes, eating utensil(s), etc. for a complete cook kit in a bag. Enjoy!
@InjunOutdoors5 жыл бұрын
Turn the key ring inline with the handle, close the handle over the lid then tun the key ring 90 degs That should help it lay flater, I think
@rtoguidver36515 жыл бұрын
If the handle was u shaped it would fit in the pot, and a notch on each side of the cup would hold the wire up. Just adding my two cents to an already great idea..
@tildensnow25342 жыл бұрын
Your lines look like they match with the handles just fine.
@ntfd603 жыл бұрын
I'm not sure if someone commented, but 1cup is approx. at the lower wire handle connection and 2 cups is approx. at the upper wire connection. Nice video.
@davidlahaisejr74792 жыл бұрын
I like the modifications you made
@jaredkeesee8143 Жыл бұрын
I mark my cups by adding the desired water and placing a large clothes pin or clamp over the cup till the tip of the clamp touches the water. You can pour the water out and make identical lines inside and outside the cup based on the tip of the clamp.
@dcbuckler3 жыл бұрын
Great mods brotha . if you drill the holes on the ends near the handle and across the holes wont be in the same area when you pour with the handle on.....just my 2 cents
@kevinflorer12114 жыл бұрын
I used the Plastic tab A number of times in the Field. Never had a Problem, do like your Concept for that MOD. I have had the cup for sense 2012. My Stanley works great I do not need to drill holes in it. If I should have to MOD that I'm sure Ill have a Gerber and a spare Key ring.
@carlrooker4 жыл бұрын
Turn the lid 90° from where you had it, and the split ring will fit right through the handle when it is in the locked position.
@MountainParameters4 жыл бұрын
Sounds like a DIY spot welder would serve you well. Since I put one together, I've been surprised by the number of projects that I can use it with.
@Iridium2424 жыл бұрын
Yeah, I am working on picking one up, a decent smaller harbor freight wire welder.. nothing all too serious for projects like this.
@MountainParameters4 жыл бұрын
@@Iridium242 FWIW, I did a fair bit of research, as I needed to weld a lot of Li-Ion batteries. After hours going through the forums, I ended up buying one that comes as an Arduino kit from a guy in Germany. House electrical outlets cannot supply enough current to operate a spot welder properly, so this one is powered by a car battery. I've been using it for a couple of months, and I am happy with it. I have also noticed when watching other videos from some of the more experienced vloggers, they are using the same one. There's lots of info in many of the forums.
@dougw92246 жыл бұрын
For a suggestion, put a piece of "heat shrink" over the key ring as well as the wire loop. It would add insulation without weighing anything.
@Iridium2425 жыл бұрын
That is a good idea, I did use it a few times since then and the ring gets warm but not super hot, but still it would work well and I do have some extra heat shrink tubing that would fit this, thanks!
@bryanadkins42085 жыл бұрын
i would consider silicone tape. heat shrink would shrink even more from the heat you are trying to avoid...right?
@TNBushcrafter5 жыл бұрын
@@bryanadkins4208 Heat shrink tubing has a point where it wont shrink anymore.
@mystuff14055 жыл бұрын
Does shrink tubing get brittle?
@TNBushcrafter5 жыл бұрын
@@mystuff1405 it may after time. Cheap stuff most definitely.
@flynnstone35802 жыл бұрын
I have and use both of these, but did some test and found the Stanley 1.1 cooks and boils water faster then these. A lot of flame gets wasted up the side because there smaller size, but they save space.
@Seamus30515 жыл бұрын
Interesting and innovative modifications...thanks for sharing.. Cheers.
@grizzlytaco34476 жыл бұрын
All great Mods! I love these Stanley cook kits! I have 2 of them! Im going to try these mods! Thanks George!
@Iridium2426 жыл бұрын
Cool, yeah I want to give the pot a try with a tripod and see how it works next!
@grizzlytaco34476 жыл бұрын
Iridium242 That should work pretty good!
@alwaysbepreparedwithjeff32453 жыл бұрын
Thanks for sharing your life travels
@craplivioncraplivious68584 жыл бұрын
very cool ideas.just 2 thoughts,you might be able to make the keyring standup by slightly bending the key ring apart before feeding it in.that might create a bit of tension to keep it selfstanding.and if you have 2 stanley cookers can make a double boiler slow cooker to not have to worrie of burning food.because your boiling temp cookin the food
@robertmiller26292 жыл бұрын
Also Wal-Mart also sells a 3 price ditty bag set and all of the components along with a boy Scout mess kit style of cooking set will set into both the medium or large ditty bag set to keep the inside of your back pack clean.
@dgriggster5 жыл бұрын
I love this! Thank you, sir!
@viewsfromedsshed53565 жыл бұрын
Great video, avid follower, always tune in. Would it be better to drill the holes just above the existing handle, and opposite. This wouldn't affect the pouring capability when using the handle. Plus this way, you could keep the existing handle on and have the hanging system. On the hanging wire, I'd make that more of a triangle shape, it'd then fit inside the container after use! Just a few thoughts. But that's what's great about your videos, they inspire thought 👍
@dcr7495 жыл бұрын
Great ideas! Thank you!
@guns4funcajanajustin6 жыл бұрын
Good tips and mods!
@craigbetts15866 жыл бұрын
good mods to both the cup and cook pot
@philupdegrave7316 ай бұрын
The cups that come with Stanley 2-cup Adventure pot hold exactly 1 cup. Good for measuring.
@shelliecarlson70152 жыл бұрын
You could also mark the cup on it, the way you did the cup. Not bad. Fit in my motorcycle kit nicely. Good video.
@mrwes1004 жыл бұрын
If you put the key ring half on, it’ll stand up.
@sojourn15444 жыл бұрын
No it wont
@Westsmoke233 жыл бұрын
Yes it will sometimes you just have to be smarter then the lid
@mrwes1003 жыл бұрын
sojourn I do it all the time.
@shaunmcgowan8273 жыл бұрын
@@Westsmoke23 it's that time. Lol
@robb56215 жыл бұрын
Add a center bend in your hanger, you probably already did this after the first time trying to hang it. Good mods.