This video shows the steps required to get a PC floppy drive to work on the Commodore Amiga. Please skip as required as I do digress on several occasions!!! Oh and I meant to say kapton tape not kynar!
Пікірлер: 20
@ubermick42083 жыл бұрын
You basically did it the way I'd do it - give up faffing about with a tiny resistor, forget a step, have it take a little bit longer than expected, but have it all work in the end. Good man yerself, Kris!
@dasfaustsretrogaming26202 жыл бұрын
Been fighting an Amiga 1000, I have a few of those Sony drives, I'll be doing this for the 1000 and the 2000, thank you, subscribed
@MrRobbyvent5 жыл бұрын
Thank You , I had success just minutes ago on a MPF920 Z121. Now I have to find a way to modify the drive's push button to fit into Amiga case. Help needed!
@StephenFinkNRP5 жыл бұрын
I have this same model. How did it work out for you?
@MrRobbyvent5 жыл бұрын
@@StephenFinkNRP well, currently I didn't find a solution for the push button and I'm pushing it by inserting a screwdriver into the floppy's button hole. It is fun to see how no one publishes a guide to address this part of the mod. They just show You only the easy steps!
@ojbeez52604 жыл бұрын
@@MrRobbyvent I'm thinking of making a 3D printed button for just this purpose.
@blackterminal6 ай бұрын
Some people have had to cut the drive itself to fit in.
@PaulVes4 жыл бұрын
Thank you for your video, it was extremely helpful. This mod also works with the MPF920, T/B63 version.
@blackterminal6 ай бұрын
Its a lot of work. I have three Amiga 500's one now with a kaput drive. I think ill use whichever one still has a working drive and if they all faulted then consider this mod.
@cicalone707 жыл бұрын
But if I would to use it like external drive, have I to remove the pin (DF1) anyway?
@apacher64337 жыл бұрын
Is this modification suitable for the sony MPF920 Z / 1M1?
@niandrastrat64885 жыл бұрын
Will this mod work to make the floppy work on a Ensoniq eps 16 sampler?
@ComplexityScience7 жыл бұрын
Do you do anything differently to use the drive as DF1?
@psyolent.6 жыл бұрын
Leave JC31 jumpered with the zero ohm resistor and don't move it
@dasfaustsretrogaming26202 жыл бұрын
Works on a Sony MPF920 T/B53 Oct2005 Rev A00
@whoisme6782 жыл бұрын
I'd like to see a disk made operational with one of the yamaha keyboards. Sy85...sy55...
@volkerking59326 жыл бұрын
with a soldering iron it takes 2Secounds to remove this 0603 Resitor.
@skonkfactory7 жыл бұрын
I like your Scottish accent. Don't do yourself down.
@pickoftheglitter3 жыл бұрын
In case you have the MPF920 Z/171 (or another release with the 24 pin IC model) you should connect the pin #34 to the IC pin #22 I found (but not tested yet) a project on Thingiverse for a 3D printed button: www.thingiverse.com/thing:3402428
@cicalone707 жыл бұрын
I have the same model, but inside is different. I 've changed the pins and it works like external floppy, If I change the pins it works DF0: too. Strange