Hello sir, is it possible to drive 3-phases bridge using IR2101 ? Thank you
@munaemhashmi44818 ай бұрын
I am using ir2104 and i am confused because of Sd and In pin where to connect plus i am making it for BMs kindly guide what will be the load
@minhtran70963 жыл бұрын
Is there any particular formula to calculate the capacitor and resistor value?
@ineskhaldi5496 ай бұрын
You find?
@the-beneficiary18092 жыл бұрын
What do I do If the power going to the mosfets are 120v dc, and the mosfet gate drivers are using separate 12vdc. How can Vs on the gate driver connect to that high voltage on the mosfet shouldn't they not be connect and stay isolated what connect to Vs on the mosfet driver then beside the bootstrap circuit capacitor from VB?
@moddyblues71203 жыл бұрын
hey man, can u explain why C2 is 4.7uF? ty
@dr.haiderzamanlecturerelec77373 жыл бұрын
C2 must hold enough charge to turn-on high side MOSFET. It depends on duty of high side mosfet
@dr.haiderzamanlecturerelec77373 жыл бұрын
I set that roughly, can range from nF to few uF
@biniambrhane68183 жыл бұрын
can we use the same circuit to drive three phase inverter i mean six MOSFET
@dr.haiderzamanlecturerelec77373 жыл бұрын
Yes! You can need three driver ICs in that case.
@zakariambarki64902 жыл бұрын
Hi doctor i don't have model ir2101 in isis.Can you send me this library thanks.
@fihtednight67234 жыл бұрын
what if just use just the hight side does that work ??
@dr.haiderzamanlecturerelec77374 жыл бұрын
We are driving two MOSFET here, the one with floating source terminal is driven using high-side while the other having source terminal connected to ground is driven with Low-side drive. If you have one MOSFET to drive you can use either the high or Low-side driver depending on the source terminal connectivity.
@rendymuhammad80902 жыл бұрын
Can we use lower spesification for rlc compoents?
@dr.haiderzamanlecturerelec77372 жыл бұрын
Use RLC relative t switching frequency.
@rendymuhammad80902 жыл бұрын
What is the value of RLC components if we use 50hz frequency?
@ineskhaldi5496 ай бұрын
@@rendymuhammad8090did you know the value of RLC components please?
@selmanmegoura54674 жыл бұрын
hi sir.What would happen if we chose only one input and one mosfet !!!!
@dr.haiderzamanlecturerelec77374 жыл бұрын
You can leave one side floating. Either use high or Low-side driver is fine.
@tilotamakodam18103 жыл бұрын
@@dr.haiderzamanlecturerelec7737 what should be the circuit consideration in this case i.e I want to use it in low side then what should be the circuit consideration be
@dr.haiderzamanlecturerelec77373 жыл бұрын
@@tilotamakodam1810 you can leave the high side floating. Means no need to connect.
@tilotamakodam18103 жыл бұрын
@@dr.haiderzamanlecturerelec7737 thank you sir for your reply... Can you guide me making a driver circuit .. struggling to make one
@dr.haiderzamanlecturerelec77373 жыл бұрын
@@tilotamakodam1810 You means simulation?
@nustanature26554 жыл бұрын
Hi sir, can you please let me know how to design a driver circuit that I am struggling with the driver circuit design?
@dr.haiderzamanlecturerelec77374 жыл бұрын
Let me know your design challenge.
@nustanature26554 жыл бұрын
@@dr.haiderzamanlecturerelec7737 I have to design buck converter of input voltage 200v with output 48v using Ir2184 driver in ltspice could you please me?
@dr.haiderzamanlecturerelec77374 жыл бұрын
Please let me know your challenge and I will try to resolve.
@nustanature26554 жыл бұрын
@@dr.haiderzamanlecturerelec7737 My challenge is I am not able to figure it out, right capacitor values for bootsrap circuit and I am confused with Ir2184 driver connections, I can share you my design spec, if you give me communication details.
@dr.haiderzamanlecturerelec77374 жыл бұрын
send me at hdrzaman@uetpeshawar.edu.pk
@longdongsilver47193 жыл бұрын
It's urgent that you buy a microphone...
@rayank993 жыл бұрын
this is a synchronous buck converter
@dr.haiderzamanlecturerelec77373 жыл бұрын
Yes this is synchronous buck converter, the low side device is a mosfet