Motorcycle rear tire change with homemade tools

[@137bob3d]

sept 18 ... last month i paid the folks at the Florence CO motorcycle shop $47. to do what you just did. put on a brand new 18" rear tire on my '04 Yamaha xt-225. the original tire lasted 11k miles & 20 years. thus having your tool would mean it collects a lot of dust. and caused me needless effort and money. how one uses their time is an important decision the front 21" wheel/tire are within my means to change with a couple of 24" tire irons from H_Frt. still tho my hat is off to you. good creativity shown here. and skill w/ movie making.

[@Pasodiack]

Thank you Bob ✌

[@CubanRider]

My man, that's a nice set-up you have going on!

[@danielkoerner7127]

Excellent video! Economy of motion and it shows in how simple it looks. Great job!

[@paulrevere9071]

NICE HOMEMADE TOOLS. I'M SURE HAVE SOME OF THAT MATERIAL LAYING AROUND IN MY SHED.

[@Pasodiack]

✌

[@roberthedan8924]

Awesome, gonna start looking into fabricating my own as well. One advice, NEVER run your fingers underside to check if the bottom bead has set properly. You could be in for some major pain if the bead pops at the same time. Safer to get down on one knee and look, or use a mirror.

[@payhommage]

My grandfather lost a part of his pinky from doing exactly that!

[@josedios3647]

CAN YOU MAKE A VIDEO ON HOW TO MAKE YOUR MACHINE?

[@TrollGnonpom]

Yes, go buy it. It's not homemade and if it is, it's very well equipped metal workshop made

[@grahampickles4488]

Try doing that with a metzeller kroo Street tyre zero give in the tyre

[@BangChief_AllIsOne]

Great design! Solid creation. Salute

[@Pasodiack]

Thanks ✌

[@BangChief_AllIsOne]

@@Pasodiack Salute

[@darseyno1520]

Fantasic work Paso. I had changed my tire on a sx1000 and sadly tore the tire. They are very hard to get on, but with that lever that you have it looks to be a god job

[@Pasodiack]

Hi Darsey, thanks for your comment :)

[@alessandropolati9694]

Hello, congratulations for the beautiful DIY tire changer construction, I'm interested in doing it too. etc.) But I do not know the measurements of the bracket where there is the Teflon wheel (diameter, thickness), and the bronze pin (diameter, height, etc.). In short, a bit of all the measures that can help me develop that bracket. Am I asking too much? thank you.

[@gilperez3581]

I really appreciate the close up on the ends of the tool bar, but I think people were waiting to see HOW you made the tools and where you get the materials.

[@Pasodiack]

unfortunately when i built this i didn't take pictures or videos ..

[@dtrail125yt3]

Can you show a material

[@alessandrovattolo592]

You're the best. Your machine is fantastic

[@Pasodiack]

✌👋

[@anubis8680]

Excellent ingenuity, on the last bit of bead seating make sure you can get the top far side down more. That tire was stretching out too much I think. Crazy great idea though!!!

[@kevinchamberlain7928]

No wrecked rims from your shop, Paso! Well done!

[@Pasodiack]

;)

[@sportsmobile8328]

I would love to have that setup!!! Nice job. You should be selling those.

[@chop_chuiey2327]

let the tool do the work, using hard poly plastic great concept. thanks for sharing

[@Pasodiack]

Hi Jack, thanks :)

[@bikenavbm1229]

nice kit and good video to show how to use it, appreciated . I am not too bad with the tyre levers. that stand and method would be nice though , will look at your other stuff.

[@Pasodiack]

Hi bikenav bm, thanks so much :) subscribe to my channel if you have not already done so and stay tuned ;)

[@petersmith7001]

Sweet setup Paso. Regarding the white pieces: What are they made of and did you machine them? I've seen the pry-bar design before but wasn't sure how to make it. Thanks.

[@Pasodiack]

Hi Smitty, the white pieces I made them myself and the material is nylon, to make it more fortr I drilled the center and inserted a 10 mm thick bolt.

[@spacecoastz4026]

I've never seen such a soft tire.

[@cardinalsin6313]

A hit of hairdryer heat goes a long way. 👍🏻

[@1jasonover]

Awesome set up my friend. Muy bueno, eres un maestro en lo que haces. Now please send me one

[@RobSummers993]

Where did you get the nylon parts from? Great vid. Thanks for sharing.

[@Pasodiack]

Hi Roberts thanks, I have realized the nylon parts with my lathe.

[@1995dresser]

The way you Thought out That Bead Breaker is Very Clever . That's a lot better then wrestling with it on the Ground and you can go around the Tire with out moving the Tire Nice Job

[@Pasodiack]

thanks.. :)

[@Bfly1211]

Do you have any more info on the design?

[@Pasodiack]

Hi ttoo, the design of my equipment is very simple as you can see, if you need the measures to try to build one, I can help you..

[@davidbrun-cosme4507]

Paso Hello, i very intersting about your design, i change much tire to race and i use a simple tire dismount, Can you sens us your design ? Plan ? Thanks you very much.

[@Pasodiack]

Hi David, I have realizate this tools with a plane in my mind only, follow my project in a similar way, and you will certainly be able to build your tire changer.. ;)

[@baazigaj9125]

That seems pretty soft rubber..nice job btw

[@andylad6449]

Great job. Its blue too!

[@Pasodiack]

Hi Andy, thanks :)

[@Flowsalvador]

Excelente...!!! De lo mejor que he visto. Gracias...!!!

[@stephenmcqueen4029]

It’s more like my homemade professional tools really. I break the bead with a half moon garden edging tool wrapped in a piece of split hose then use tyre levers and rim protectors to remove the tyre. 2 decent blocks of wood on the floor to keep it off the gravel. Appreciates better not to do this on your knees but your kit takes up a lot of space and is bolted down too. Mine just stacks away in the corner.

[@tomasguerrero9622]

Awesome. Maybe you could use something similar to a bead buddy to help put the tire on the rim instead of those pieces of wood. I'm sure you could fabricate those yourself!

[@DavidM2002]

I've made all of my own tire mounting / de-mounting tools as well and am always looking for ways to improve them. I particularly like your mounting bar end. When you use your de-mounting bar, the bar is to the right of the center post and you turn clockwise. But, with the mounting bar, although the tool is to the right of the center post, you turn counter clockwise. Is that intentional ?

[@Pasodiack]

Hi David, you are an excellent observer, however it is not intentional, the instrument is made so that it can be used in both directions of rotation of the bar on the central pivot without conditioning the operation..

[@Almer654]

Jamás vi tanto amor al momento de sacar una rueda mis respetos para el señor ama su trabajo

[@Pasodiack]

gracias Almer :)

[@monirhossen2544]

What is materials you use for tyre brushes? Shampo, glass cleaner, oil or others

[@Pasodiack]

car shampoo mixed with water

[@Za_TA]

soapy water best,

[@m.t.8181]

Oi Paso, assisti o seu video tambem tenho uma Kawasaki ZX12R . Voce tem as especificacoes de construcao do seu projeto? Gostaria de construir uma com estas dimensoes. Grato, Mucci

[@timo3100]

Paso, looks really super. and no scratch on your rim? Where did you get that tip( white) on lever

[@Pasodiack]

Hi, thanks, no not scratches on the alloy wheels thanks to the nylon tip that I worked and put on the tip of the lever.

[@timo3100]

@@Pasodiack i want to build this lever with the nylon tip. Do you have some drawingplan and dimensions of the lever.

[@nadhighlander]

thats a lot better than jumping on a spade to burts bead impressed with this might try make one :)

[@rodraynolds9692]

What kind of tire changer is that?

[@Pasodiack]

HI Rod, I designed and built my tire changer ✌

[@alexmorgan3435]

A good one.

[@650nelson]

honestly, the music?

[@Pasodiack]

Hi Pete, I made the video with some copyright free music and everything was ok, then after a long time i got a notification for copyright problem of a music, i had to remove that piece of audio to make my video free again.. this was the only possibility of modification.

[@GioSinatraFan]

Where did you buy the white lexan/plastic material? I assume you shaped it yourself, but I'm interested in what the material is and where you bought it. Thanks

[@Pasodiack]

I used the nylon to make the part, i bought the nylon cylinders in an industrial warehouse.

[@eroscava]

ottimo..semplice e funzionale. devo decidermi a fare 4 buchi al pavimento del box perchè la stabilità è tutto...

[@СергейМ-ж1п]

Отличная работа！Лайк. 👍

[@Pasodiack]

thanks :)

[@Martins_uy]

Un gran trabajo, un trabajo muy fino y delicado, felicitaciones!

[@Pasodiack]

Hi Martin, thanks :)

[@andrewdavis5404]

Love your tools ,very clever

[@Pasodiack]

Hi thanks :)

[@talk2kev]

Very cool tools well thought out , I need to build one of these the bike shop charges way too much to mount a tire. And the design it beats working on the ground. It looks like 6 inch channel that makes up the legs do you have concrete anchors in set in the concrete so it can be unfasten and moved. is that a 5 gal steel bucket for holding tools? a 2 to 2 1/2 inch pipe up to 1 inch 1/2 cross that holds the tire rest I see you put screws at the bottom ends of each cross brace so the tire rest can not come off do you have a set bolt in the rest to keep it in place? Also where did you get the plastic parts? sorry for so many question but I'm going to make one , Paso Great job on the build looks like you take pride in your work.If you built another one would you change anything? Stay awesome

[@Pasodiack]

Hi Kevin, thanks, for your questions; at the base of my tool there are two bolts fixed to the floor that prevents movement, the other two bolts are in support to recover the difference in height of the concrete. I made the vinyl parts myself with my little lathe. I plan to build another better one in a future time, stay tuned ;)

[@talk2kev]

It turned out great

[@timmytool1231]

Way to many parts all you need is two tire pry bars, stem remover, soapy water, done. I've done them all of my life.

[@garychandler4296]

Don't forget the 2x4 blocks to keep the rims and discs off the floor! Thumbed up!

[@TheBless3d]

So how do you break the beads with just two tire pry bars? I was thinking of getting a manual tyre changer but if I don’t need to...

[@garychandler4296]

@@TheBless3d The irons have 2 different curves on the ends, and it's pretty much self-evident. Consider that dirt bikers that do rallys or enduros fix flats beside the trails in minutes with little 6" tire spoons! I sometimes crush my tire in my big bench vise to break it, or have used 2x4's to set up to drive the front wheel of my pickup on it...a V8 powered bead breaker!

[@TheBless3d]

Gary Chandler I hear you. I’ll keep watching vids on here and decide whats the cheapest and best way for me and my R6 and XJ6

[@markman63]

How did you make that white plastic tip to lift the tire off the rim?

[@Pasodiack]

Hi, I have a small lathe with I build the pieces of my projects.

[@guillermoramirezduque3745]

Donde conceguir esta máquina?

[@contitradebestdrive5194]

TOP! Golden Hands.

[@Pasodiack]

thanks ✌

[@abahocygarage]

Simple tools n it's works. Great job👍👍

[@Pasodiack]

thanks bro :)

[@ralphwaters8905]

Around 10:44 I noticed some bubbles at the bead. Is this common? I suggest you search eBay for a "plastic tire mount demount duck head" made for a professional tire mounting machine such as made by Coats. These wear items sell for about $15 delivered and will save you a lot of DIY hassle. Spin one direction to remove, reverse to mount.

[@Pasodiack]

Hi Ralph, this is a video of the year 2018, I have purchased the component you have suggested already since some time, I purchased two pieces from China, they are made of metal and with Teflon inserts so as not to scratch the alloy wheels, it will be part of my next project.. Subscribe to my channel and stay tuned.. ;)

[@vitomir-vitovladika3265]

if u wanna sell it ( tire changer ) what would be your price ???

[@steven.h0629]

Start by by looking at what's already made.. then take the useful bits from those and build on it.. good solid base and connectors is key.. start by looking here > www.harborfreight.com/search?q=tire%20changer

[@oficina3erodaschoppers828]

Bacana jovem, parabéns. Roda ficou perfeita e sem riscos.simplesmente show

[@Pasodiack]

Hi Antonio, thanks :)

[@billzanotti9886]

great video !!!!

[@cezzar5552]

Red point on the tire is rather the haviest part of it, isn’t it? It should be on opposite side of the valve.

[@sultanheart]

Its the lightest part of the tire and should be where the stem valve is

[@MovieMan797]

The thing that has the shape of a cone, is it teflon or wat is that and where did you get it?

[@Pasodiack]

Hi, the material is nylon and I did it with my lathe.

[@Juicebarltd]

Cant get my tyre to sit in the bead. I try pumping it and no lucky. Any idea what to do

[@Pasodiack]

you have to lubricate the bead of the tire with soapy water and then inflate until the bead enters the seat of the rim.

[@Juicebarltd]

@@Pasodiack I'll try the rachet strap method. The issue is sealing the tyre to even start pumping it

[@fredoswego]

@@Juicebarltd I find just really cranking down on the tire with ratchet strap running the circumference works for me every time. I will add, you more than likely need a real air compressor or one of those portable air tanks - something that can push a fair amount of air fast. You won't seat the bead using a $20 12v tire pump.

[@scummy73dude64]

Very small amount of brake cleaner and a lighter. Works every time. Be sure to have the vale stem out when you do this

[@human1513]

@@scummy73dude64 You mean have the valave stem's core out.

[@dipankarpoddar763]

Dear sir can you helf me this idea I need this type machine

[@Alessandro.Garzya]

Yellow circle should be alligned with valve, red circle should be alligned with the point of wheel rim where this stick out less

[@Br4m76]

how do you make it?

[@Pasodiack]

sorry but I don't understand what you mean.

[@pleasetakeasip4556]

Paso the tool

[@helydacabrera848]

Muy lindo... soy de Argentina Misiones... como se ase una de está....

[@Pasodiack]

Hola Helyda, muy gracias :)

[@วัลลภจีเมล์จ้า]

Thanks so much.

[@0110-g9n]

Great work. Can you give me link sound, please

[@Pasodiack]

Thanks Rio, the sound: Ikson-Alive (free to use). link: kzbin.info/www/bejne/jn6ldGuQq9acb9k

[@BudFox559]

Great design

[@Pasodiack]

✌👋

[@xisidro972]

Hola muy buen invento soy un capo un abrazo😀😀😀

[@Pasodiack]

Hi Isidro, thanks :)

[@mangjca3009]

Did u made that tool sir?

[@Pasodiack]

yes, are tools created by me.

[@joker-js5bc]

very nice idea....good job sir!!! im from philippines....

[@Pasodiack]

Hi Jo, thanks :)

[@rubenrojas4272]

Exelente video y la herraienta mejor. saludos. MX

[@marcind1323]

Good job, without scratch.

[@robsonmattos4979]

Show, o cuidado e o amor em fazer as coisas é tudo!

[@ismaeldossantos3296]

What about the front tyre? 😕

[@Pasodiack]

Hi Ismael, look this: Motorcycle front tyre change : kzbin.info/www/bejne/n2LCg3psf96imMk Motorcycle wheel balancer : kzbin.info/www/bejne/boq1h4lun9d4qLc Motorcycle lift table : kzbin.info/www/bejne/qKOQaWtmdtWUl68 Motorcycle Front Wheel Chock : kzbin.info/www/bejne/oYHXmo2epNGMbaM if you like subscribe to my channel and activate the bell for other new videos ;)

[@juliohengler4979]

gostei, obrigado por dividir essas ferramentas.

[@Pasodiack]

Hi julio, thanks 👍

[@maiconboani9948]

Onde compro essa espátula de sacar pneu

[@hellishgrin4604]

I’d love to do something like this if my local shop didn’t do it for pretty much the cost if tire.

[@bestyousuf9709]

Indian me avilebel hai kya sir

[@pepedusud6335]

Bravo, très efficace.

[@Pasodiack]

Thanks.. 😊

[@cyclonetv6690]

Nice diy tools

[@ricardoteixeira2310]

Muito bom!👌👍😉

[@Pasodiack]

thanks ✌

[@bujangjang4709]

Good idea give me the price

[@snoopydoggy5196]

I need to use my everlast welder to make one of those tools.

[@edigomes2061]

Helo my friend, I'm brazilian. can you make vídeo speaking and expleining, please?

[@Pasodiack]

500,000 views :) many thanks to all of you for this achievement ;) sign up for my channel if you don't haven't done it yet and watch my other videos. best regards, Paso.

[@ronalimagno1100]

Hi can you share how did you made your tool,thanks in advance

[@Pasodiack]

HI Ron, try watching this other video : kzbin.info/www/bejne/ppzQgpSqnrOKeaM

[@muammerusluer1211]

Onemli olan lestigi sokme yada takma degil , takmadan once balans ayari yapilmasinda , gerisi teferruat.

[@Pasodiack]

Maybe you don't have visited my KZbin channel, subscribe if you like, you can see my static balancing tool that I built and how it should be used in this other my video : kzbin.info/www/bejne/boq1h4lun9d4qLc

[@vuiluong3995]

Hello, are you for sale?

[@Pasodiack]

Hi, I am sorry but no..

[@sanjoynewmaking1058]

How to make new design Dirt Bike

[@heatherrrenea]

Sorry but I don’t see the homemade tools. Looks more like a manual tire changer bought from harbor freight for $49.99.

[@Pasodiack]

Hi Nappy, sorry but it seems own that you did not take a look at my channel to see my other videos of my equipment built at home, otherwise you would no have made a comment like this just because you no have seen the phases of realization of this .. :)

[@rrl2849]

@@Pasodiack That is a very nice machine - Thanks for sharing.

[@Pasodiack]

Hi rrl2849, thanks :)

[@Rhaspun]

Ha,ha. When I saw the caption for the video. I jokingly thought of commenting that is why with homemade is when you can go to Harbor Freight.

[@Pasodiack]

@@Rhaspun - si certamente, tu puoi andare dove vuoi.. :)

[@adriantompson]

that good watched it twise going to make one thanks for the idea,

[@Pasodiack]

Happy to have inspired you ;)

[@motik954]

Video is normal, but you need to be careful when you install the rubber on the disc, so as not to hit your head on the pin!

[@camaradam16]

Thanks broo!!!

[@piun020900]

buenusima es HERRAMIENTA PARA DESMONTAR RUEDAS

[@Pasodiack]

Hi Salino, thanks :)

[@SpayNeut.Always]

Good job, thanks for sharing

[@Pasodiack]

thanks John :)

[@bak2drt240]

So where are the Home Made Tools. ??

[@Pasodiack]

in my video above...

[@myhamer6003]

Your job very good very good very good

[@bestyousuf9709]

Price

[@Saga-k4l]

Байка .оторвать хорошо хоженую резину на такой шпильки 18 мм.не возможно согнется не особо напрягаясь.

[@michaelstrauss6587]

very nice.....muy bueno

[@Pasodiack]

Thanks Michael :)

[@faridalrangkuti3882]

very usefull

[@ajoodas6572]

I,m from indonesia god jobs amazing....

[@Pasodiack]

Hi Ajo, thanks :)

[@Chris-of8ps]

I would like to add that if you first brake the Tire bead on the floor first flipping the tire breaking the beat again on the other side then mounting it on this tire changer you will save a lot of time

[@jhonathanrivera5061]

thanks for the video but those are not home-made. Maybe you did it at home. However the concept of home-made is something than almost any person could do with household tools

[@Pasodiack]

Hi Jhonatahan, to build this equipment I used one lathe and one welding machine, if this means for you that they are not made at home then I can answer you that if you only have a screwdriver and a pliers you have very little chance of building something complex, at this point you can't build nothing .. do you agree with me?

[@lemoinexavier]

Well done, but boring video. Gave a thumb up for your time...

[@Pasodiack]

boring video? this is a video showing the replacement of a tire with my making tools, what did you imagine to see? :)

[@lemoinexavier]

@@Pasodiack I know, gave a thumb up, but it's way too long...

[@АлексейБахарев-е5х]

Attaboy. Молодец

[@Pasodiack]

thanks :)

[@splatharackal1337]

That tool is too much thicker, will damage tyre edge. Make a tool, that is thinner,

[@steven.h0629]

.. now that you said it.. show your tool bro. Mine's a bully.. no fighting >> www.turboimagehost.com/p/41775614/IMG_1214.jpg.html

[@claytonfabiodasilva6683]

Very very good !

[@Pasodiack]

Hi clayton, thanks :)

[@ВиталийБушин-ж9з]

Спасибо понравилось