Well, time to replace my charge port. I didn't know the G30 had no back adhesive. That makes my job a heck of a lot easier.
@PBKreviews Жыл бұрын
👍
@vincentoyenga31863 жыл бұрын
amazing i followed the way and did my own change of broken lens !!
@PBKreviews3 жыл бұрын
Nice, glad you were able to do it!
@reinierdvl3 жыл бұрын
in practice, disassembling this device is more of a pain, mainly because of the battery. We all know that a small damage in the battery can lead to a fire and it is mounted in such a way that damaging the battery is a very high risc. Also it is nearly impossible to remove the buttons without the risc of damaging them. This was confirmed by a repair tech that said that basically they will not do repairs on the Moto, because there is a high risc of damage. The ones that will do it wil charge 140-150euro as they will also replace the battery, rather than removing it. No-one I asked will replace just the screen. The screen is mounted to the frame in such a way that replacing it alone is hard and difficult as alignmend needs to be near perfect. A 150euro for repair is a whooping 20euro's less than a new device. What they recommend me was to buy a new or used device and clone the damged device, or, when that is not possible to a severely damaged screen, just replace the main board between de damaged and new device, if keeping your data is critical. Repairabillity imo should be a 3
@PBKreviews3 жыл бұрын
For screen replacements, it would be easiest if you found a replacement screen with frame combo like this (www.ebay.com/itm/393485687240?hash=item5b9d9319c8:g:Gm8AAOSwf61hC63c) so that you don't have to pry the screen off. Also for the battery, yea its difficult, but you can use isopropyl alcohol and apply it around the edges of the battery and let it sit for 20 seconds and then try to pry the battery off and apply a little more isopropyl alcohol if needed so it gets under the battery to eat away at the adhesive making it easier to pry off. Hope that helps. Here is a link for the isopropyl alcohol: www.ifixit.com/Store/Tools/iFixit-Adhesive-Remover/IF145-400?o=4
@christiankortmann581 Жыл бұрын
I actually tried to repair it and damaged the battery aluminum foil and it started to melt. Dont do this !!
@Subhasis445973 ай бұрын
Pour alot of alcohol under the battery, before trying to pry it out. Use a playing card, not the guitar pick as shown here.
@DrumsForBeginners3 ай бұрын
I can't thank you enough for your video!! I managed to replace the battery and surprisingly everything works!!
@PBKreviews3 ай бұрын
glad it was helpful :)
@b28mathstutor Жыл бұрын
Really helpful, thanks. My husband's G30 charger port has stopped gripping the charger cable (though it still charges if held carefully in position) and after watching this I'm confident of being able to replace the relevant board.
@PBKreviews Жыл бұрын
No problem. Also check and make sure there isn't lint and other debris stuck around the inside of the charger port. Sometimes that's the cause of it.
@dan332463 жыл бұрын
hola amigo mi moto g30 resivio un golpe en el blindaje superior ala lado de la camara y no enciende, no resive carga.. que podria hacer, tendra algun tipo de arreglo?
@PBKreviews3 жыл бұрын
Hi, its possible the screen got a small hairline crack in it somewhere on the corner where you can't see and that may be preventing it from working. Also can be other internal damage or a loose battery cable. Try one more thing, hold the volume down and power button at the same time for 30 seconds and see if it will boot up. If not then it might be one of the first things I mentioned.
@dan332463 жыл бұрын
@@PBKreviews lo lleve a servicio tecnico y me dicen que toca quitar la parte el blindaje donde esta la pelicula de granito, sobre el blindaje plateado. es posible arreglar esa tarjeta con ese tipo de golpe o toca remplazarla?
@JohnSmith-dl7yk2 жыл бұрын
The shield on the back side of the processor is dented due to impact on the back of the phone and is doesnt turn on or charge. Is it completely broken or is there anything I can do? Cheers.
@aatrani Жыл бұрын
Excellent video!! I was able to replace the swollen battery of my partner's phone thanks to your video!!
@PBKreviews Жыл бұрын
Glad it was helpful 😀
@mihaistoescu10393 жыл бұрын
Is there any water mesh at the speakers or microphone? Does the camera have OIS? You could have moved the camera with the tool to see.
@PBKreviews3 жыл бұрын
There is mesh filters for the speakers and mic but no rubber gaskets or water resistant type filters. No OIS on the cameras, they are fixed in place camera's so no point in poking it with a tool since they wont move, its not hard to see that.
@walkerwalker9574 Жыл бұрын
how do you remove the speaker at the top you didnt even show that, please and thanks
@pixelman80443 жыл бұрын
Hello, would you Disassembly to MOTOROLA E6 plus 32Gb XT2025-2? Thank you.
@PBKreviews3 жыл бұрын
Hi. There are already some videos of that phone being taken apart if you search on KZbin.
@Daktangle9 ай бұрын
In order to replace the battery do I need to do a full disasemble or can I just go so far as to expose the battery connection and then replace it?
@PBKreviews9 ай бұрын
Just as far as gaining access to disconnecting and removing the battery.
@Daktangle9 ай бұрын
@@PBKreviews Wonderful, thank you!
@jemoeder93852 жыл бұрын
How do you remove the earspeaker and vibrator motor?
@PBKreviews2 жыл бұрын
They are held down with adhesive, just heat it up gently and pry them off.
@bbbaaa68252 жыл бұрын
i succeded it also without heating, just put something sharp underneath and push carefully
@jemoeder93852 жыл бұрын
@@bbbaaa6825 aaah yes it worked, thanks 🙌🙌
@madushan42 жыл бұрын
Hi . My moto G20 charging port is not working. Is it same as the g30. I have to replace the power board
@leecollins54972 жыл бұрын
Can you replace the phone jack?
@PBKreviews2 жыл бұрын
Headphone jack is soldered to the board, would require soldering knowledge to replace, and the charger port is on the sub board and that would just require replacing with a new sub board.
@ankitfulara55002 ай бұрын
Where is Power management IC located
@BSEmadcow Жыл бұрын
How easy is the speaker to replace on this phone?
@PBKreviews Жыл бұрын
Not too difficult. You can use the video as a guide to walk you through it. The earpiece speaker on top is held on with adhesive, so you can heat it up and pry it off. The bottom one is held on with those screws on the plastic assembly so that one is easier.
@bbbaaa68252 жыл бұрын
Hey, thank you. I succeded changing my display. Some tips from a non professional: buy the alchohol and do it properly
@PBKreviews2 жыл бұрын
You're welcome. Yup, I now use the isopropyl alcohol. :)
@angelabeatrizcerda92363 жыл бұрын
Hola te amo una pregunta el módulo del G20 es compatible con la de G30 ?
@PBKreviews3 жыл бұрын
Are you referring to the motherboard? It might be but I'm not 100% sure.
@salamidealer2 жыл бұрын
I ripped the cable from my fingerprint sensor is there any way to fix that easily or am I gonna have to bring it to a professional
@PBKreviews2 жыл бұрын
You would need to replace the fingerprint sensor but its not too difficult. You can follow the video if you feel you would be able to do it, if not then best to take to a professional.
@zehronyao63542 жыл бұрын
Hello Bro, Is this the model of xt2129?
@PBKreviews2 жыл бұрын
yes correct
@soumyajana63793 жыл бұрын
Woow ❤️
@gheorghebucurici69263 жыл бұрын
even I have a motorola like this and I like it
@PBKreviews3 жыл бұрын
👍
@devilgaming055323 жыл бұрын
❤️❤️❤️.Nice teardown video . please tear down moto g40 fusion and moto g60
@PBKreviews3 жыл бұрын
Thanks, will do it soon.
@mariusliebenow980810 ай бұрын
Thx for the Video 👍🏻 after i replaced my Screen, the NFC doesn't Work any more. What have i done wrong? Where ist it located? Do you know? 😅
@PBKreviews10 ай бұрын
You're welcome. The NFC antenna is on the back cover, it has two gold pads where they touch two gold pins on the main board to give it signal. Make sure the back cover is seated in place properly and that the gold pins on the board are not damaged and make a connection with the NFC antenna points when the back cover is in place.
@vinothparamasivam3 жыл бұрын
My moto G30 touch has been broken still display s perfectly working nd everything is perfect kindly suggest can I transfer touch alone?????
@PBKreviews3 жыл бұрын
Hi, no touch digitizer is fused to the screen. You would need to replace the complete screen assembly.
@darrenmarrable25302 жыл бұрын
Excellent
@PBKreviews2 жыл бұрын
👍
@nakul3019 Жыл бұрын
Display rate?
@greedy4sure3 жыл бұрын
Where can I find the lcd screen replacement my phone drop it still powers on but it’s blank and I still feel vibration when it’s on.
@PBKreviews3 жыл бұрын
Here is a link for one amzn.to/2U3khL4
@greedy4sure3 жыл бұрын
@@PBKreviews thank you really appreciate it
@PBKreviews3 жыл бұрын
@@greedy4sure you're welcome
@pimpinal0043 жыл бұрын
Cool
@shaoo59472 жыл бұрын
Many thanks
@PBKreviews2 жыл бұрын
You're welcome
@olegphilonenco64868 ай бұрын
Спасибо
@NitishKumar-rn2ll3 жыл бұрын
Hello sir please make moto g31 disassembly
@PBKreviews3 жыл бұрын
Hi, i will do it as soon as it comes in.
@tricky7783 жыл бұрын
Can the glass lens be removed and replaced without all that disassembly and without replacing the LCD and digitiser? It seems obviously wrong, when the glass is the bit that will break, to tie it to the lcd and digitizer - those knockoff lcds and digitizers are a great place to put a man in the middle attack and collect info from/trick a vast portion of the earth's population - and our computers are now powerful enough to pull it off. Meanwhile, when the manufacturer provides cheap brittle glass, all I want to do is swap the glass for a low price.
@PBKreviews3 жыл бұрын
If you are talking about the glass on the screen, no it would not be possible for an end user to replace just the glass. Its fused or glued to the screen itself to reinforce the screen since screens are much thinner now a days compared to back in the day. Only factories with special tools and machines can replace the glass from the screen.
@tricky7783 жыл бұрын
@@PBKreviews it would be better from my perspective to glue the display and digitiser to the frame of the phone and a slim tough substrate on the front to provide it with support and surface protection then let me debond and bond lens material as an ablation layer across the display and bezel as necessary
@kitocrazy2 жыл бұрын
The Brazilian channel HD Tec Celular is replicating this video.
@PBKreviews2 жыл бұрын
Hi, yes he's obtained permission and is giving credit for the video. Thanks for the heads up though :)
@nishkm Жыл бұрын
Hello Sir, I am from India. My battery is totally f*** and I need to replace it. Could you kindly tell me the battery model of this g30. Thanks in advance.
@PBKreviews Жыл бұрын
Hi, its a JK50 battery
@BMS-p8i Жыл бұрын
My vibration motor is dead, although i bought it new, in unboxed it myself 😓