Mounting a 70" TV on Harbor Freight Armstrong 37-80" Full-Motion Pull-Out TV Wall Mount 64357 Review

[@larryjohnson7591]

Pretty good coverage of how the mount is installed and how well it works. Thank You.

[@striker1211]

I'm glad the video helped you. It's a great mount, I'm glad I didn't buy the cheaper one that the TV "hooks" onto on the wall.

[@brandonterrelle]

I just bought this mount and needed to see how to install it and your video does just that. Thanks. Also Congratulations on your baby🙂!!

[@borisattva]

i was on the fence about getting this one but the video convinced me. thank you for your time and effort!

[@Colt-Forty5]

Thank you for this recent video! Plan of buying this mount tomorrow.

[@Godcreatedmj1]

Hi Striker Thank you so much…I just googled this product and decided to check out KZbin channel and clicked on your video and like your demo!

[@joyuncovered]

Nice job on the video! Thanks for showing the weak areas in the mount design!

[@achernan3309]

Hey, Striker 😁 Amazing video, as always!

[@eljustin76]

Good video💪🏾 I just bought this tv mount to put my tv outside and it’s a concrete wall… it’s save for the concrete wall? Asking because the bricks. Thank you in advance.

[@HughWoo]

You used excess man. There were spacers I saw on the mount attached to the TV that weren’t necessary. (Middle)

[@Fotosynthesis858]

Mine works well & I got it for barely over $40. I mounted mine to the bricks on my fireplace & it’s super sturdy.

[@DCash704]

Is there a way to tilt this more to one side? Mine looks crooked but when I have my leveler on the wall it's straight but the brackets holding the TV is not.

[@striker1211]

If yours is flexing that much you may need to tighten up the bolts on the arms that pull out. I don't remember there being adjusters.

[@DCash704]

@@striker1211 I found out what I did! The 2 screws on the bottom were too far over its perfect now! Thanks!

[@kotabailey2037]

I just bought this Mount at harbor freight thanks for the video

[@mayadillard8248]

Simple and easy video 💙installation tomorrow same Mount. Your right it’s heavy.

[@sgianino0719]

Funny i mounted this exact unit today and thought the same thing, if that 1 fastener fatigues at the top it could fall forward.....i like that idea of the safety strap just in case

[@mertcancan6309]

Is it safety for philips 70pus amblight tv ?

[@jason5409]

Good eye to point out the weak link of those 3 screws holding the tv on. Bad design. I installed eye bolts above the mount and ran a steel rope through the plate to reinforce the mount in case it breaks or that bolt gives out. I'll look into that thing you put on there. What exactly is that?

[@striker1211]

I used stainless steel zip ties. They are amazing.

[@Joe-dz7kj]

Now that’s using your head brother👊🏼 great tutorial!

[@DapimpBDSD]

I use Mounting Dream mounts off of Amazon, I've bought 3 (different styles for installation) and never had a issue.

[@krldrai]

Hello Striker, Thanks for this vid. I am thinking of getting this product. any long term review? Tv still mounted without problems?

[@SteveHoward-qv6ws]

Nice instructions and points made. ty

[@beardedgaming1337]

my computer is mounted to this bracket. no issues

[@potterportraits]

does this allow the tv to be moved to the left or right from center mount and be flush with the wall. i'm looking to put this behind a door but want to be able to extend it over a closet.

[@striker1211]

No, only when centered can it be flush to the wall. The length of the arms in the middle do not allow it to sit flush while right or left of center. I have my TV off the mount right now so it was pretty easy to check for you. Good timing.

[@potterportraits]

@@striker1211 thank you! So much. I' really appreciate it

[@dl3908]

How the hell did you lift that giant TV by yourself to put it on the mounting brackets?! As a single woman with a 50-inch TV I'm completely stumped how I'm going to lift mine!

[@striker1211]

Newer TVs are incredibly light. They are just awkward to hold. Be careful not to put any twisting force on the TV, keep your grips square, hands at 12 and 6 or 3 and 9 oclock.

[@audreycristina123]

Thanks for the video!

[@maverick_edc4014]

Are those bars that go on the mounting plate go there only if the holes are spread out?

[@striker1211]

Any TV over 32 inches is going to need to use the bars. Only computer monitors or 25ish inch TVs would use such a small VESA mount to not need them.

[@veecemx]

​@@striker1211I have a 65 inch with vesa 400x200 and in the instructions its pictured and it says to use the horizontal bars on 400x200, is that right or always use all 4 bars?

[@nllandry]

Currently I have a 55” TV I want to mount now but in a month or so I’ll be upgrading to at least 65” would the mount position to the wall need to be changed? If not, do I need to mount the wall side TV mount higher to accept the larger tv in a month? TIA!

[@striker1211]

Yeah you will probably be switching from Vesa 200 to Vesa 400 where you don't have room to adjust it, so you'll want to mount it a little higher. Going from 55 to 65 will require you to bump it up about 3 inches but bezels vary so you have to get your new TVs exact dimensions, subtract new tvs height from current tvs height, divide by two. Raise it that much.

[@ben12079]

The proof load of a grade 5, 1/4 inch bolt is over 1,000 pounds. They’ll be fine.

[@Daygogal]

Doesn’t push back all the way back to its place

[@ELINDOOR510]

Where you get the stainless steel "zip tie"?

[@striker1211]

Amazon, search for 100 pc stainless zip tie there are tons under ten bucks

[@brandonsawh5689]

Bro where the video of you putting the mount together? We all know how to do the rest we need an assembly video man

[@striker1211]

The assembly instructions from Harbor Freight were unusually detailed so I did not upload that part. I might see if I have it in my b-roll folder.

[@toughc2000]

Awesome...thanks

[@Daraina]

Thank you!!

[@descalf]

LAG bolts NOT leg bolts!

[@deandreduncan4035]

Good

[@bryanthubbart2611]

EMT 4209

[@dalexander4204l]

. . . . .language, buddy. language :)

[@DoraTheMFDestroya]

the parts bags each have several numbers on them for me, and nothing fits right. i feel like i got an absolute lemon.

[@TTrent-xc1ep]

So what tools do I actually need to do this?