MT09 / FZ09 / FJ09 / Tracer 900 exhaust modification with photos and video ride by

[@waynep4256]

Nice work... at least we can see where the cat is now,thanks for the video 👌

[@mohamedhassissi5414]

My God this sounds way subtler and better than the Akra and two brothers! Genius work pal

[@stratos2811]

i did the same too...sounds great..not louder than any other aftermarket exhaust. for daily use is awesome. i remapped ecu too and its awesome.

[@Dzajs]

I did it the same. Thanks for instructions. If anyone have questions - ask

[@kml3277]

I do this the same with my exhaust. Is many work, 8-10h for make good job. At low revs around 87-89db, at 5k revs around 99-101db. Over 85km/h and if not accelerate you hear almost only wind. The most noise while riding is at 2-4k revs, big bass. Before I had good full replica real carbon Akrapovic but it was 8-10db louder. I also tryied moded it for reduce noise but nothing helped. For me was too loud for daily use. Than after 500km, yes I only recommend mod oem exhaust.

[@timcarter7051]

Great work...did the same thing to my Aprilia Futura's "bread box" years ago . Going to do the same to my 3week old Tracer but going to cut off half of the "bread box" like l did on the Futura and it worked great.

[@MrToastedBlue]

The first time I did this I made the box 60mm narrower, made for a bit of extra work though. this time I didn’t bother. just got my 3rd MT09 last week and will be doing it again but this time I’ll cut the bottom off as it makes life a whole lot easier for doing the exit pipe as you can bolt the exhaust back on to line it up. Tip... the 50mm header pipe continues into the box about 50mm. If you cut carefully around where it enters the box, just passed the weld, you can pull it out before cutting it off, gives you a bit more to play with 👍🏻

[@barnyboysdad]

well done man,I did similar to a cb650f I had a few years ago,it produced a great exhaust note and to all and sundry appears to be a stock muffler, until you open it up ,love it ,stay safe enjoy your bike , cheers 🍻 Robbie Renalson Devonport Tassie

[@firdhausismail]

Superb sounding ! This is arttt

[@frankstocker5475]

Great work very creative.

[@tonigsxr1100]

Great job. I’ll copy 😉

[@dominikz9748]

is this thick pipe in the middle on the left a catalytic converter?

[@michituurbentaler1378]

proper work! thanks for the helpful photos

[@kostaschatzi6391]

Nice Job Boy !

[@stevenkerry3101]

nice sound good job .

[@mylesgriffo]

Hey mate, did you have to do any re-mapping etc? Did it suffer and side effects? Thanks for the vid.

[@MrToastedBlue]

no remap, no negative effects on the engine, just a healthy 5bhp increase for very little money. did the same to my 1st MT09, rode it for 18k miles and no issues, current MT09 is on 7k miles, again no issues.

[@mylesgriffo]

Awesome. Thanks for the tip (and being the guinea pig :)) Cheers

[@donnyazoff980]

Nice job mate, sounds great! Did you notice any difference in performance? Did you lose any low down torque?

[@MrToastedBlue]

Yes, got 4.6bhp increase, ran it on a dyno before and after on same day

[@okgo55]

Hello boss, o2 sensor works after mod?

[@MrToastedBlue]

Yes

[@darransus7113]

Hiya, I done this to my Kawasaki Vulcan s, did you see an increase in fuel consumption?? since I done mine on my Kawasaki it drinks it 😔

[@MrToastedBlue]

Darran not something I take much notice of really, didn’t seem to get any less to a tank of fuel though 🤷🏻‍♂️

[@SidiD12]

Did you notice any gain or loss of power? Failures?

[@MrToastedBlue]

ran it on a dyno and there was a 4.6bhp gain, bike had done 18k miles when I sold it and had no issues

[@SidiD12]

@@MrToastedBlue Thank you my friend, I am considering performing the procedure on my motorcycle. Greetings from Brazil.

[@TheFedericator]

Hey Bro! Really nice work, is it too loud in comparison to an after market (with dbkiller) like an akrapovic or it is on the same decibels level?

[@MrToastedBlue]

it's not too loud, just sounds great, mate has an Akra without the DB killer and that's much louder than mine. there's about 250mm of baffling in the main box that keeps the noise level a bit lower but it's basically a 50mm straight through pipe... do it :)

[@giorgosmark8591]

catalyst is in the pipes you removed?

[@MrToastedBlue]

yes, the catalyst was removed, it’s now a straight through exhaust with no restriction

[@SuperSpoon1974]

Hi Mate. Do you know , if any mt 09 exhaust fits to the tracer or from specific year?

[@MrToastedBlue]

Takaro standard MT09 exhaust fits, only difference is the shroud, aftermarket will also fit but you might have to remove the centre stand

[@SuperSpoon1974]

@@MrToastedBlue Thanks for your reply. Have a great day.

[@enzofortunato5057]

Buonasera a tutti qualcuno di voi ha uno scarico originale modificato per Yamaha tracer 900

[@lsimsek]

Cool 👍🏼👍🏼👍🏼

[@ytrbolanda]

Mega!

[@adik90911]

Nice video and smart modification bro..have explode after that..? How about pick up compare factory exhaust..?

[@MrToastedBlue]

as far as I can tell there's no negative effect on performance, the exhaust makes it "sound" faster anyway, and the mod gives 4.5bhp increase for very little money

[@davidrespect6471]

@@MrToastedBlue How do you know that you gained 5hp did you dyno it before and after? Also did you saved any weight?

[@MrToastedBlue]

DAVID RESPECT I did almost the exact same mod on my MT09 and ran it on a dyno, theres a video, the only difference being I made the silencer box smaller but internally it was the same. as for weight, couldn’t tell you exactly how much was saved, I was more interested in making noise and power 😁

[@MrToastedBlue]

DAVID RESPECT this vid... kzbin.info/www/bejne/opOUiIuwgbt6bKs

[@a453365fg]

Good

[@JVal-xc4xs]

Can you tell me the diameter from pipes? because I want to do the same on my tracer 900 and one more question who many hp you take and take you on duno?

[@MrToastedBlue]

Γιάννης Βαλβης stock is about 52mm O/D but I used 50mm as it fit the exit pipe shroud perfectly. dyno’d it with stock exhaust then the modified exhaust (on the same day) and got a 4.7bhp gain

[@JVal-xc4xs]

And the cm from one side to other side ?

[@JVal-xc4xs]

Have you same email or Viber , messenger ?

[@MrToastedBlue]

Γιάννης Βαλβης I’m guessing you mean one end to the other ? don’t know, didn’t measure it 🤷🏻‍♂️

[@jsnyper4357]

Mickey mouse

[@gerasischristos8750]

Cheap sound!!!

[@MrToastedBlue]

gerasis christos no idea what that means but thanks :)

[@Jrouse37]

Hey this is the same exhaust that is on a 2016 fz09 correct?

[@MrToastedBlue]

yes, it's the same exhaust except for the brackets for the exit pipe cover and the cover itself, but Tracer 900 will fit FZ/MT09.