Multi-function DC/AC 5V - 24V Forward Reverse Motor Controller Timer I053A02

How to set the Forward time, reverse time, stop time for all function, setting the time, setting trigger and demonstration. The module is from ELETECHSUP. You can set the minimum time to 0.1 second and maximum time can be set to 9999 minutes or 166.65 hours.
The best thank you for me is to not to skip ads and Subscribe 🔔 to my channel, like 👍 the video It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe and enable the bell 🔔.😊
Jump to different section of video by clicking on the time:
00:00 Hardware explained
-02:21 How much current this module needs?
04:45 Power save mode settings
05:35 Module settings
07:25 Reverse Time settings
09:00 Setting STOP time
--10:55 1 is 0.1 Second, 2 seconds, 3 is minutes
11:05 wiring Explained
12:51 F-11 Setting and Demo
18:11 F-02 Setting and Demo
20:21 F-11 Setting and Demo
22:21 F-12 Setting and Demo
23:31 F-21 Setting and Demo
24:27 F-22 Setting and Demo
25:07 Trigger setting (option 9) Falling edge or Rising edge
26:13 Conclusion remarks
Purchase this item:
AliExpress: s.click.aliexpress.com/e/_ASRYwe
Amazon USA: amzn.to/2IH27c2
Amazon Canada: amzn.to/3kLRMNd
All other Amazon: amzn.to/3zd7yo9
Visit resources page for this module: robojax.com/L/?id=120
Tutorial by Ahmad Shamshiri form Canada
****************************
Arduino Step by Step Course (over 150 lectures) Starts here • Lesson 00 What is Ardu...
****************************
If you found this tutorial helpful, please support me so I can continue creating contents like this. Here is PayPal link paypal.me/robojaxTV
Follow me on Facebook robojaxTV
Follow me on Twitter: / robojaxtv
Follow me on Instagram: / robojax
Tutorial by Robojax.com
Get other projects code and learn Arduino
robojax.com/learn/arduino
*** AFFILIATE PROGRAM ***
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
#robojax #robojax_timer

[@jw11432]

At 14:30 he glosses over the loop function, for anyone wondering. Function 8 is the number of cycles. 0=Loop forever 1-99=number of cycles to loop Hope this helps others, I've seen quite a few comments about the looping function.

[@dangruen]

Thanks - very helpful - and this is a critical function. I found a clue to this in a table I found by googling "canton electronics Model IO52B02". Instructions there are a good supplement to what is in this video.

[@Trainwheel_Time]

Thank you!

[@crackoffski]

Awesome... been searching everywhere for that info. Absolute legend.

[@JBliehall]

jw, I have a YYB-5 control similar to the one shown here. When I program P1 and short IN1 to ground it only runs the A timer. It does not automatically go to the B timer. When I short IN2 the B timer runs. When I program P2 and short IN1 only the A timer runs. No C timer or B timer. I tried seconds and minutes configurations but it still never automatically goes from the A timer to the B timer. I altered the all times to be sure it was programming correctly. Any suggestions are appreciated.

[@BeGood2DoGood]

Nice. Would you have a list of all the functions for this board or a url where I can look that up? Need to see what other options are available.

[@alexn9775]

Very awesome, informative video. I’m doing a little project and needed this little board. You explained everything so well it literally took me 5 minutes to set the whole thing up. Thanks a lot my friend.

[@nirmalmaan1437]

Amazing video. Helped a lot with my son's technology project. We ordered this from Amazon but didn't receive any programming instructions. We tried for many days but we could not figure it out. My son was so frustrated and we were about to return it, but we came across your video and it was a lifesaver. Very Helpful. Thank you so much.

[@pjm780]

Thank you for posting this! It was very helpful.

[@dangruen]

REPEATING (LOOPING) PROGRAM: Several people have asked how to set the board to repeat the cycle automatically. Essentially, parameter 8 sets the number of times to repeat, 1-99. 0 means repeat indefinitely. Default is 1. I found a clue to this in a table I found by googling "canton electronics Model IO52B02". Instructions there are a good supplement to what is in this video. (Shoutout to jw11432 who also addressed this in his comment).

[@DasFelixx]

Thanks. Worked welll for my project :)

[@robojax]

Great!

[@namtr0]

One of the best overview and review videos I've ever seen. Where have you been and why did I not find you till now. Sub'd

[@robojax]

Google bias towards me in search result made it not to be found.

[@robs8036]

Usually I hardly comments but I salute you for this video thanks

[@robojax]

It's my pleasure

[@anupshekhar4501]

To be frank the video is really nice and I liked the way you have made and explained settings . I wish you could help your viewers with their doubts rather asking them to watch the video again. Questions they hv asked were not covered by you in this video

[@robojax]

Because I don't remember. I have to watch to answer, so if I can learn from watching, then the person should watch and get the answer.

[@Micjavier]

Good job. God Bless.

[@robojax]

Thank you. God Bless.

[@TheSolutionGerm]

What a thing I love it

[@robojax]

Good to know. Thanks.

[@patrickkirby4705]

Thank you for this helpful video. Can this unit be programed for two different stop times?

[@jakvlogpedesaan]

Likes, good job

[@robojax]

Thanks.

[@goosphil]

Hello Ahmad, and thank you so much for your comprehensive video. I looks so difficult for me. I am looking for a module to trigger a linear actuator. In fact, I just need the function F-12. By chance, do you know if a simpler module that does just that exists? When the linear actuator arrives at the end of its path, there is an internal switch that cut the power. So, my idea is to set up the time for the same length as the linear actuator, so, when the linear actuator arrives at the end of his path, the module will cut the power and wait for the reversed trigger. Am I right?

[@LestersCustomTrkShp]

Great video! Where can I get a copy of the instructions you showed, on the AliExpress page, that can be printed out?

[@tkomic19]

it would be great if they had something like this w a simple wifi

[@tylerjmechem]

Hi! Great video! Can this be used with an 110V 750W 1HP Sewing Machine Servo Motor? And can you suggest what wires and trigger to use to initiate a forward,stop,reverse cycle?

[@raknin]

Great video. 1. If one cycle of f01: t1 t2 and t3 completed in order to activate it again i need to diconnect the 5v power and connect it again? 2. If i want to do one cycle of f01:t1,t2,t3 and afterward want to start a new cycle of f01:t1 do i need to be program it again?

[@prodipdoley5945]

Sir how to setiing use linear actuator forward auto backward and stop

[@GozMeu]

I would like to know this also and with a remote control?

[@Mike-iq8uv]

Thanks for the reply - the problem I was having was I used the same power source for the motor and control circuit. Once I suppled them separately it worked fine. In my final application though, I will only have one 12v (battery) source to power both. Is there a device I can use to isolate the single supply and essentially make it two independent sources? Thanks

[@robojax]

you are welcome. I have not see. for AC there is isolation transformer.

[@JBliehall]

I have a YYB-5 control similar to yours. When I program P1 and short IN1 to ground it only runs the A timer. It does not automatically go to the B timer. When I short IN2 the B timer runs. When I program P2 and short IN1 only the A timer runs. No C timer or B timer. I tried seconds and minutes configurations but it still never automatically goes from the A timer to the B timer. I altered the all times to be sure it was programming correctly. Any suggestions are appreciated.

[@astropacc1951]

I’m planning on using 2 of these on funtion 11 one for each 100w 24v dc motors each motor will be moving in the opposite direction at the same time of day how can I trigger this to work on a timer I want it to open curtains at a set time of day then close them at a set time Thank you

[@roxytbbs]

Thanks a lot for this explanation. English is not my native language. But the only question I have, is it possible to set at auto repeat? So for instance forward for 2 sec, stop for 0,5 sec reverse for 1 sec and then forward until trigger van Capatative sensor and repeat? Hope you understand what I mean? Thanks in advance.

[@robojax]

you are welcome. have made over 460 videos and don't remember what I said. But when I explain something, I don't leave details. So if you watch this video multiple times, I am sure you will understand all the features. good luck

[@sachinGharat41071]

Wel explained,thanks a lot

[@robojax]

You are welcome

[@ubuthi7495]

Good video. Can you set it to repeat the forward reverse action continuously for a few hours? Thanks

[@robojax]

thank you. Everything this does i have shown it. Nothing left. So watch it fully and see which part is useful for you.

[@ubuthi7495]

@@robojax Yes I see it only runs one program forward stop reverse and stop. You need another switch to manualy or automatically start it again?

[@robojax]

it should have loop to repeat it.

[@anupshekhar4501]

Even I am looking for that answer or a circuit that supports this feature

[@anthonyhodgson3427]

Can you set this repeat the action continuously? Like forward for 5 seconds, stop for 5 seconds, reverse for 5 seconds then stop and repeat the cycle again ? Also can you connect a speed controller to the dc motor and it still work normally ?

[@robojax]

Hello, I have explained and demonstrated all features of this and don't remember anything about it. so if you watch it multiple times, you may understand all the features. but for sure nothing is left out. so watch and find out.

[@RichRocketMan]

Can this be used to control an actuator in the same fashion? Actuator extends for specific period of time, then pauses for specific period of time, then reverses direction for a specific period of time. I would be looking at a 12 volt actuator arm. Thanks!

[@AztecWarrior69]

Why wouldn't it?

[@RichRocketMan]

@@AztecWarrior69 Great! Thanks!

[@Mike-iq8uv]

Hello, I just watched your video and programmed the unit. It works, but now it won't stop running the program. F8 is set to one, but it just keeps going. I saw a factory reset option of pushing the ++ and -- buttons simultaneously for 5 seconds, but that doesn't stop it either. Could it be defective?

[@robojax]

Hello, if it doesn't do what it is supposed to , then yes. it should be defective. But I would suggest following exactly as shown in video.

[@webadvertising1]

Is it possible to use only Funktion 1 without the separate switches? Just with a switchable Powersupply and an a Motor like wiring in your example?

[@robojax]

I don't remember what I said in the video. but this has different functions. with trigger (when wire is used) and without trigger (without wire). So yes. you can. you have to watch it fully as I have explained all functions of this module. good luck

[@xispaki]

i got the following problem! i fitted this board on the 4x4 - 4x2 system on an ATV...it works like a charm except every time that i turn on the key, it will run for the direction where the switch is on! Is it possible to configure this board in orther that evary time that it turn on, it doesn't run the motor? Thank you for the help! Cheers!

[@skullzrm]

I don’t know exactly what you are using this for, but if you wire it to constant power and not ignition, it will not turn on every time with ignition, instead wire it to constant power and add a normally closed momentary switch on the negative lead of your circuit board, Now you circuit board will only run when this switch is pressed. Good luck to you.

[@tsrpci]

Can it be programmed in a way, that motor goes forward for desired amount of time, and than backwards for desired amount of time and repeat this cycle indefinitely? What kind of motors does this module support? In the video you used DC brushed motor. Will it work with brushless motor or AC motor as well ? Thank you!

[@robojax]

Hello, I believe I've explained the best possible way all features. so if you want watch it fully, you should get the answer. This is only for DC motor as I mention in the video. Brushless motor has special speed controller.

[@AztecWarrior69]

brushed only. set 8 to 0 for indefinably.

[@Mike-iq8uv]

Can you post those text instructions as well - I can't find them on the internet anywhere the item is no longer on aliexpress so the instructions are gone from that site. Thanks

[@robojax]

Hi, I spend time to learn about it and made the video so people see and hear.

[@samifeistenberger1924]

Hey there and thanks for this video, I wouldn't been able to get this done otherwise :-) Is it possible to program this device with Arduino or Raspberry, so I can get some individual timings into it? I would like to have it going like this: forward, stop, reverse for 1 minute, then 1 minute pause and 10 seconds forward, stop, reverse every minute. I want to use it to develop classic film with that ;-) Thanks a million for your help!

[@robojax]

Hello, I have so many of videos kzbin.infosearch?query=timer see them. there is Arduino based timer

[@samifeistenberger1924]

@@robojax Hello and thanks for your reply! I'll check some more videos from you this evening after work :-) Is it hard to program this device I053A02 without knowledge of coding? If you like classic photography, I'd be glad to share my results for maybe another of your awesome videos ;-)

[@robojax]

actually you can't update the firmware (code) of this. it is sold like that. you would have to use Arduino is the most flexible device and you can do anything you want. there are tones of codes and videos available. Yes I love photography and I spent time taking photos. but how would I use them in my videos? Share please so I look at them.

[@samifeistenberger1924]

@@robojax I see, thanks for the hint! I'm waiting for my arduino and nextion...then I'll get something assembled and will update you :-)

[@J5X7]

Can it be used with a remote fob and board wired up to it to use the timer function to a motor to open and close a door 90 degrees?

[@robojax]

may be this kzbin.info/www/bejne/ml7Mepaegd6bapo or kzbin.info/www/bejne/ZnzFlXydZ9aerpI

[@wills9627]

hi there, ive got a 24v garage door motor with a burnt out wireless reciver board that does not work, but when i applied 24volts direct to the motor it works under load which works fine to open garage door and close. i just need a replacement 220-240v to 24v reciever board relay with a built in timer. do you know which one should i buy. i dont want to buy another whole garage door opener/closer, when the motor still works. (ive all ready check the circuit board 24v reciever relay timer with i can not find no issues that i can see). ive checked aliexpress but can not find one that suits my needs, please help anyone or send me link off video that can help me out.

[@miriumsonos5277]

Hi. Can I use it without the trigger? Eg. Program it forward 5 seconds->stop 5s->reverse 5s and repeat the program indefinitely without triggering a program every time?

[@robojax]

Hi, someone else might reply. I don't remember what I said in the video but that is my rule to explain everything so if you watch it fully, you should get the answer weather you can do it or not.

[@miriumsonos5277]

@@robojax Hi. Thanks for reply. Video actually doesn’t explain this, but thats ok. Don’t worry. Maybe someone has this module and will reply.

[@raknin]

If i want to connect 220v motor and i want that the mototr spin clock wise 30 seconds and in counter clockwise 30 seconds and than repeat the cycle for 300 seconds 5 cycles. I also want to activate the cycling by push button and stop by stop button. Which connection i need to use? Every time i press the stop key the cycle will stop and every time i press the stsrt button it will start without disconnect the 5v power? I want this setting remain constant. Is it possible?

[@stebstebanesier6205]

I'm new at this electronics stuff so bare with me, I have two questions 1: can I set option 8 to 99 so the program will run 99 times. 2; I was lost when you said, "9 is that if the trigger happens continuously pressed or just low level we are not changing." what does that mean?

[@robojax]

to answer your question about "99 time" I would have to watch the video. So you watch it because I don't remember. your last question, "continuously pressed" means keep it pressed. when you press it, it sends 0V or LOW to the input. you can also use a computer or other devices to send 0V or LOW signal to make it work.

[@stebstebanesier6205]

@@robojax Thank you sir.

[@awaagrikh8331]

hi, i want to use it to do latching for water valve-a latching valve require positive pulse to turn on and negative pulse to turn off. Can i set it to forward for 0.1 sec and stop for 15 min and then reverse for 0.1 sec and delay for 12 hours before foward again?

[@robojax]

Hi, it has 3 settings. but you want 4. you want extra delay. I've explained it at best possible ways. if the thing you want to do is not possible by this module, then you might need another of this module and some how after motor is stopped (after reverse of 0.1s) then it should keep it OFF for 12 hours. and you can use the trigger feature with some wiring which I don' t know at the moment how. For that you need to check the 1st module and see after the last step which pin or location on the module is changing the state from LOW to HIGH or from HIGH to low and then solder a wire on that spot and connect that wire to the trigger input of 2nd module. Depending on the LOW or HIGH then program the 2nd module to turn ON after 12 hours. then do the same. on 2nd module find the same spot and solder a wire and connect it to the trigger pin of 1st module and it should work. It needs patience. Or simply use Arduino which opens the whole word for you and do anything you want. Program it and upload it to Arduino. See this video kzbin.info/www/bejne/gH6lmHqFZZyMgq8

[@awaagrikh8331]

@@robojax thanks for your advice. i also think that i may need extra component

[@jacksonpreisler9116]

Also is there a thinner version of this module?

[@robojax]

not that I know of.

[@sayfalnatour2354]

Can I sit it up so will forward in the morning for a few seconds then at the night will reverse. Thanks

[@robojax]

watch the video fully and you will get answer. I have not left anything out about this module.

[@anupshekhar4501]

I am surprised the way you answer questions from your viewer. They already watched the video and then they are asking those questions . Instead of answering their doubts you are asking then to watch the video again to increase your number of viewers. Very bad approach and attitude as not everyone is technically sound like you. Would request to keep a helping attitude . You may answer easily if you know the answer

[@krishnatungal]

Is this controller a avilable with Solid State Relay instead of mechanical relay? And also can you please make a video for AC motor using this controller

[@robojax]

Solid state relay will not work with DC. it is working only with AC.

[@krishnatungal]

@@robojax i need it for AC only.

[@robojax]

no. unfortunately. You would have to use Arduino. Here are my videos on Solid State relay kzbin.info/door/kcBSig_Iu4ZnAIeCeG1TVgsearch?query=solid+state

[@krishnatungal]

@@robojax i have it with Arduino. Ok, so with this I053A02, can you show the wiring please, because in AC motor, i have 3 wires, two clubbed with capacitor wires and one directly to motor, am not into electronic so, just looking for it

[@dmtycn]

Is there a board can control 120V AC motor forward and reverse just 1 button? 1st push go and 2nd push reverse? Thx. To replace a swing gate opener control board. Currently all I can find is for 12 or 24V DC motor.

[@robojax]

you can use this module with very little effort. I did not do it because people are just waiting to blame other for mistakes so I did not mention it. please do not ask me but search online how wire AC motor to rotate in two direction and (Now I have to reply safely) make sure you know understand the safety aspects of working with AC voltage. If you are not sure, seek help from a professional.

[@dmtycn]

@@robojax Haha, what's you have experienced? I already found a AC Motor control board.

[@tylerjmechem]

@@dmtycn which board did you get?

[@motto666]

Is there a simpler controller if I want to set it to switch polarity forward 5 minutes and reverse 5 minutes automatically and stop in 2 hours with 30Volts DC, max ampere less than 1 ampere? This is just overkilled.

[@robojax]

This is very cheap and if you go with anything else, it would cost you more. Here is my video if you want to do it with Arduino kzbin.info/www/bejne/gH6lmHqFZZyMgq8

[@motto666]

@@robojax Ok, Thanks.

[@robojax]

you are welcome.

[@ssssmall]

Hi I want to put powerstep on my truck and I search for the perfect module board for me. The motor is polarity. So one way is deploying and switch is stow. By a trigger. (Door). Have to be 3 sec each way. Need 12 volt. It’s on a pickup truck. If you can tell me what’s the best things I need for that Thank

[@robojax]

Hi, I don't know "powerstep" but you may use this kzbin.info/www/bejne/gH6lmHqFZZyMgq8 to change the polarity

[@ssssmall]

@@robojax thanks for answer; but if you look on youtube for powerstep you will see. i need a timer with the module polarity and its the trigger (open) start the motor 3 sec. after trigger close the motor start in opposite direction for a other 3 sec. Its near of the i053a02 you explane option 9 .. but i dont know . thanks

[@robojax]

then forget about this module. it can do only things it is programmed to do. here is kzbin.info/www/bejne/gH6lmHqFZZyMgq8 the video and start using because you can control it any way you want.

[@castelmichel8670]

Hi, does it have a loop function?

[@robojax]

I made the video to answer such questions. so please watch. Nothing is left unexplaiend.

[@bacuba64]

la ripetizione ciclica (8) funziona solo con F-01 e F-02 e non funziona con F-11 e F-12, pertanto non sarà possibile in F-12 comandare il numero massimo di ripetizioni. cerco di spiegarmi se volete che un attuatore avanzi per x volte comandato dall'impulso del pulsante non funzionerà. infatti in F-11 e F-12 manca il numero di impostazione 8.

[@kamleshpanchal8661]

I need this product , so where to I purchase for India mumbai post .

[@robojax]

Please check the links under the video.

[@jasperdelumen1587]

can the output voltage be adjusted?

[@robojax]

No. In my video explain all features in a video and never skip. This is just a relay which switches something on or off

[@anupshekhar4501]

Why can't you say in yes or no that if this circuit has option to run for few minutes forward then stops there after runs reverse. In you video you have not said anything about loop . That's the only part missing .I wish you could have clearly said in yes or no. Overall I like the way you explained the setting , very nice review .

[@robojax]

if it had loop I would have explained it.

[@x-0-x-0]

@@robojax It DOES HAVE LOOP! Quote from the page: "The number of cycles is the number of repeated actions (Nx =0 means always loop, Nx =1 means no loop). So you can set the number of loops: 1-99 times or forever loops." But it did come with 1 as default, so it did not loop and you did not dig that. You are also not aware that most anyone who would need to use a motor would need to loop probably, so an important part you skipped. You are one RUDE person, btw. I have never seen anyone answer this way on YT.

[@jw11432]

@@x-0-x-0 Dude, thank you _so_ much. I see so many people asking this question (and you're right, anyone looking for this feature will likely need some degree of looping for practicality) and this dude is rudely telling people to watch a 30 min video again instead of taking the time to check...instead of narcissistically postulating that if that function existed, he simply wouldn't have left it out. 🙄

[@tkomic19]

Hello, I see how you can do F S R, but can I also do 1 cycle F S R F F - Fwd, S - Stop, R - Reverse

[@robojax]

Hello, I have shown all features. Nothing is left without explaining it. Please watch fully and if you don't see the feature, then it does not have.

[@jacksonpreisler9116]

Does this motor driver work for any motor?

[@robojax]

it is just relay. Meaning it is a switch to turn ON/OFF and change polarity. It can control a motor at 10A for up to 220V. My test was on DC.

[@ranaadhikary296]

Truns comand then stop motor. Example 100 true then stop.

[@robojax]

you can't to it with this. you need to have encoder installed on motor so you know how many turns it did, then take some action when it reaches 100 revolutions.

[@ranaadhikary296]

@@robojax Sir I would like to order a "Multi-Function DC/AC Motor Controller Board with 24V motor, 2 relay, 1 display, photo sensors and keypad. The machine should be automatic with inbuilt program set for movement or oscillation.

[@mytrahana]

Top man ❤

[@zyadd5089]

Hello

[@robojax]

Hello Zyad? what's up?

[@cecuenwu8842]

Halo sir the speed can be adjusted

[@robojax]

This relay. It turn a off or on. No speed changes

[@cecuenwu8842]

I use an ac input adapter 200v output dc 12v 3A why can't it turn on sir. the 3F R S small light flashes red only. Pls help🙏

[@peterdkay]

Nice features but one of the worst user interfaces I have seen!

[@robojax]

Yes. They could have just used 6 digit display instead of 4 and it would have been much simpler.

[@musico119]

Hi, I accidently put more than 5v to the internal power and, now the digit panel is showing "r.r. r." and not working at all.. Did I blew up the voltage controller?

[@vladimirbondaletov2767]

Попробуйте произвести сброс к заводским настройкам.Хотя шансов востановления мало.

[@pearljameric]

Can a 12v battery that powers the motor also be used to power the controller as well? Thanks!

[@robojax]

Yes it can