Auto Forward - Reverse Cycling Motor Control 37217 RL mpja.com

Рет қаралды 15,364

2 жыл бұрын

Programmable timed control for motors & other cyclic uses. Set Forward & Reverse running time. Isolated Relay wired to reverse the polarity of the relay DPDT contacts. Cycles Forward/Reverse as long as Board is Powered. NOTE: Load Power must be removed to Stop motion, Removing Circuit Power stops the timed cycle leaving motor running continuous in one direction.
Load Power Circuit Power are isolated
Circuit Working Voltage: DC 5-13V
Working Current: 5V: Forward: 4ma Reverse: 36ma
12V: Forward: 6ma Reverse: 44ma
Relay Load Rating: 30VDC @ 2A max or 125VAC @ 1A max.
Recommend 5-12VDC Motor 2A
Run time set by programming & 3 jumper selections for X1 to X8 running. X multiplier is same for both directions Forward & Reverse base time are independent
Forward time: up to ~5000 sec. (X1) to ~40000 (X8)
Reverse time: up to ~5000 sec. (X1) to ~40000 (X8)
Terminal Strips for Circuit (Board) Power, Load Power & Load

Пікірлер: 31

@neoartschool5723 2 ай бұрын

Too bad these have discontinued I wanted to buy like 20 of these... even tho you can just program something similiar on Arduino these were perfect for a class we wanted to do... would probably have kept buying them if the class worked out... Should bring this item back!

@llanero9133 2 жыл бұрын

Thanks a lot for that excellent tutorial, I'm now ready to program my module as soon as it arrive.

@castelmichel8670 8 ай бұрын

Thanks for showing this

@davemarshall8630 Жыл бұрын

Hi Thanks for your excellent demo. Written instructions offer a complicated method. 🤔 One question - when powered down, does the module retain its settings memory? Thanks - Dave

@solarsynapse 2 жыл бұрын

I am using a similar unit with a display that I feed the motors from an ESC through the contacts. The problem is that it is fairly high current and I need to soften/suppress the change between forward and reverse to protect the ESC and gears from damage. Any help would be great!

@user-cy9yk8ky2e 7 күн бұрын

hi, thank for the explanation. can you advise on a reverse cycling motor controller that will control the speed as well?

@RaulioG88 Жыл бұрын

So it just keeps going back and forth it doesn’t stop on it’s own? I wanted to get a set up like this for my power fold mirrors just open and close both sides timed so I don’t have to hold the trigger but the trigger would stay in position give on/off would be open/close in my case

@step3prophet194 Жыл бұрын

Hi there. I got a reversable geared 6v motor, but when I plug it in d2 operates is for a split second before resuming forward motion. If I disconnect the motor relay operates as normal. Any ideas?

@finalflightcalls Жыл бұрын

What if you wanted to pause in between your forward and reverse cycles? For example, forward for six seconds, 6 second pause, then six seconds in reverse, then, six seconds pause again, and then repeat.

@davidfurst7233 Жыл бұрын

Excellent. Where can I purchase several of these

@JOATMOFA 2 ай бұрын

How would I control this device with a 433MHz push button remote control (in stead of a manual switch)?

@castelmichel8670 8 ай бұрын

Can the motor be powered at 24v using a separate power supply?

@jessemurphy1338 Жыл бұрын

Is there anyway you can ship to Canada?

@elcid8423 7 ай бұрын

Hi, do you you have a video on DC12V Infinite LED Cycle Delay Timing Timer Relay on/off Switch Loop Module? I ask because I don't speak Hindi.

@ddzang 4 ай бұрын

Can the board also be programmed to pause between forward and reverse?

@Mert-tj4pm 4 ай бұрын

that board cannot do that you need something like this ''YS-RT1M 12V''

@AztecWarrior69 Жыл бұрын

Did you know that if you solder a jumper to the 3 jumper selections for the M+ or M- connections you can actually use the multiplier for one direction and not the other. 6:18

@RuDanPlumbing Жыл бұрын

Is there a way for you to cycle this forward 5 seconds the reverse for 5 seconds and then it stops. Like maybe with an external trigger?

@AztecWarrior69 Жыл бұрын

No. Not with this one. I demonstrate this very thing in my video. kzbin.infodHeIsAFeYvo It runs for one cycle or as many cycles (up to the max the module can do) as you like. OR infinite. If you do not need it to stop before reversing, set the stop time to 0. Recommend you give it at least 1 second.