Mustang BBK Throttle Body/Intake Plenum 1996-2004 Installation

  Рет қаралды 125,624

CJ Pony Parts

CJ Pony Parts

Күн бұрын

Пікірлер
@YipperX5
@YipperX5 2 жыл бұрын
the idle tip at the end was a nice touch! as a newbie to modding, I just fixed my extremely high idle thanks to you! I completely missed that section of the manual and thought "more air must mean an increase in idle? I guess that sounds right"
@jordonk6799
@jordonk6799 3 жыл бұрын
Thanks for the tip on adjusting the idle.
@morrisf3957
@morrisf3957 3 жыл бұрын
missing the horse 🐎 emblem.thats the best part.
@andys9053
@andys9053 Жыл бұрын
Was there any issues with gas pedal placement after? Seems like I have a lot of play on the throttle cable even tho I ran it around like stated?
@bryansmith1872
@bryansmith1872 9 жыл бұрын
Great vid...keep em coming!
@TraceyEaster760
@TraceyEaster760 7 жыл бұрын
u make it look so easy
@kqarmen1
@kqarmen1 9 жыл бұрын
when you lifted up the stock tb there was still a vacuum line still attached that you disconnected what does it go to or used for at ((3:11)) ? i had forgotten to connect mine one time and noticed alot more power even if it had rough idle
@mistywells542
@mistywells542 6 жыл бұрын
Good queation vaccume maybe into firewall and to the back of the climate control i believe
@johnsluyter7432
@johnsluyter7432 Жыл бұрын
Just purchased this for a 2002 Mustang. My BBK throttle body did not come with the steel vacuum nipples on either side or throttle position bushing. Tried to remove factory tubes to press into new throttle body. Before I press them in, I wonder if mi e is defective and missing pieces.
@viprk24OC
@viprk24OC 5 жыл бұрын
+CJ Pony Parts Wish I saw LMR's video first. You installed the hardware in incorrect locations, The screws you used on the IAC valve were ment for throttle linkage. The bolts you used on the throttle linkage punctured straight through the throttle-body, and in my case one bolt head broke clean off when trying to loosen it.
@kevinleatherwood7823
@kevinleatherwood7823 3 жыл бұрын
Same here!
@viprk24OC
@viprk24OC 3 жыл бұрын
@@kevinleatherwood7823 Yeah both CJ and AM get things wrong in videos. I check LMR's first now.
@mikelitoris1371
@mikelitoris1371 4 жыл бұрын
listen to him gentlemen. Disconnect the battery
@sethschronce376
@sethschronce376 4 жыл бұрын
Best name ever
@austinharrison2453
@austinharrison2453 4 жыл бұрын
But why disconnect the battery...
@Guenter34
@Guenter34 3 жыл бұрын
@@sethschronce376 😂
@thomasbatts672
@thomasbatts672 4 жыл бұрын
What is the hose on the back of the throttle body for you disconnected it last before the throttle body was able to come off all the way
@leohealth123
@leohealth123 2 ай бұрын
What is the purpose of that bushel added to the new tps sensor receptor bay. is it necassary?
@jaysixfive0922
@jaysixfive0922 5 жыл бұрын
I wonder what’s the exhaust of the mustang at the end of the clip
@cjponyparts
@cjponyparts 5 жыл бұрын
BBK longtubes and a Magnaflow cat back on a 4V
@shorty004
@shorty004 6 жыл бұрын
They dont supply the supply bushing
@Travissantos
@Travissantos 4 жыл бұрын
Hi, what is the part you’re removing at 2:19 ? Mine were cut and I can’t find the specific name for the part to be replaced.
@cjponyparts
@cjponyparts 4 жыл бұрын
They are vacuum lines.
@andrewgamache3867
@andrewgamache3867 6 жыл бұрын
I've got an 04 grand marquis 4.6 2v that I'm building and this should fit it as well correct? I can't find anything else for it, the intake tube shoots off to the drivers side, so just reversing the direction of this plenum should do the trick.. but BBK will be upside down, sigh visuals are part of the fun! Lol
@WestsideWoo
@WestsideWoo 10 жыл бұрын
Great vid
@budd2018
@budd2018 5 жыл бұрын
So this is totally fine and smog legal ? I have a super low mile 98 gt. I just put a cold air and exhaust on it. I'm ready to buy one now but would love a bit more reassurance ...... if it will work well with the cold air and exhaust I'd pull the trigger. Also was looking into underdrive pulley kit. Will be supercharging it after I find out smog situation with that. Any other bolt on smog legal power adders are welcome.
@cjponyparts
@cjponyparts 5 жыл бұрын
Yes this is 50 state legal and has a CARB EO number. It will work well with a cold air and even better with a supercharger. If you are planning the SC route don't bother with underdrive pulleys, you will have to remove them for the supercharger.
@javierguevara1238
@javierguevara1238 9 жыл бұрын
I have the AirAid CAI along with this 78mm TB on my 01 GT feels wayyy powerful!
@julianlopez2138
@julianlopez2138 8 жыл бұрын
Javier Guevara what size coupler did you use cause i have an airaid CAI and i cant find ot make the coupler fit
@TyroneS_
@TyroneS_ 3 жыл бұрын
Same I’m looking for a coupler also
@djrayray55
@djrayray55 5 жыл бұрын
I have a 98 mustang gt PI swapped with long tube headers and x pipe and cold air intake. I ordered a 75mm throttle body for my set up. Will that hurt my engine
@martinbuilt
@martinbuilt 5 жыл бұрын
well I am familiar with the Dodge 4.7 V8. I also did long tube header single 3" exhaust and a custom ram air then added an upgraded manifold and a custom GM 75mm throttle body and I had the WOW factor. So I would say go for it.
@willroman5082
@willroman5082 7 жыл бұрын
which one you recommend on a 01 gt with a K&N intake , headers, expipe with full exhaust, flow masters and 3.73 gears , the 73mm or the 78mm ?
@deivid4048
@deivid4048 7 жыл бұрын
I have a 2000 gt , with k&n intake,racing headers, borla mufflers,4.10 gears and the 70mm throttle body and it works perfectly. I think you need more than that to install a throttle body of those sizes
@jayseonb7498
@jayseonb7498 4 жыл бұрын
Shows everything but how to hook the throttle cable up 🤣
@dhatbwoy696
@dhatbwoy696 3 жыл бұрын
Omg... it's busting my nuts how to put it back lol
@garcia1177
@garcia1177 2 жыл бұрын
At loss for words how he put the back. I’m guessing great mechanic skills but I spent like 45 mins trying to get that stupid cable back in place. He made that shit looks so easy also.
@hermanrogers1325
@hermanrogers1325 3 жыл бұрын
What size throttle body should I use for n/a with a cold air intake and cat back exhaust pypes
@dougp5044
@dougp5044 Жыл бұрын
Is it good for just stock or is it more for forced induction setups?
@AdamAve93
@AdamAve93 7 жыл бұрын
Would this work for a 99 town car with the 4.6? Already have an edelbrock victor jr intake manifold on it so I’m trying to see if it’s compatible.
@mmmmmMuffinz
@mmmmmMuffinz 4 жыл бұрын
youd need to get an adapter plate to go on top of the victor jr intake. here it is: www.cushmanmotorsports.com/cms-edelbrock-victor-jr-4-6-2v-intake-adaptor/
@rushbullet892
@rushbullet892 2 жыл бұрын
Does anyone know why my 4.6 2v idles around 1200 rpm, it has a stage 2 comp cam. The iac is perfect, but I think its because I have no intake filter
@MichaelGsandup
@MichaelGsandup 7 жыл бұрын
I'm looking to get the bbl 1685 tps sensor for my 01 gt will I see and difference with the bbl tps compared to the stock Ford tps sensor?
@islamjesus777
@islamjesus777 9 ай бұрын
What's bbl?
@baconator407
@baconator407 5 жыл бұрын
Where can I find the "vacuum fitting"? The one with the two red lines coming out of it that are connected to the throttle body? I cant find it anywhere
@brando9751
@brando9751 5 жыл бұрын
So this will work on a 96 without a PI swap?
@rickybobby6386
@rickybobby6386 2 жыл бұрын
How in the hell do you put the pcv adapter in by hand and mine won’t even go halfway down with a socket. Tf
@ramirogovea3092
@ramirogovea3092 9 жыл бұрын
If I put this on my 02 GT, is it California Smog Legal? Would it still pass smog?
@Mr.Johnny831
@Mr.Johnny831 7 жыл бұрын
Ramiro Govea Yes it is California Legal NOW! Here is the EO # D-245-17, your welcome!! :) and by the way the dealership that sold me my mustang is no longer in business (I wonder why.....) had illegal mods installed in the car and sold it to me that way, So I barely found out 2 years later that my car wont pass smog. So I did A LOT of searching until I found this one. Thank God!! Lol.
@Mr.Johnny831
@Mr.Johnny831 7 жыл бұрын
It was approved July 18, 2016
@TraceyEaster760
@TraceyEaster760 7 жыл бұрын
any time u see mods ask to see the smog!!
@barneywarwick2110
@barneywarwick2110 5 жыл бұрын
i have a 2005 crown vic police insepter 4.6 motor would that throttle body work on my motor I'm trying to find ways to get more horsepower
@Panchitoisdead714
@Panchitoisdead714 4 жыл бұрын
Yes it will!
@sergiobullitt4509
@sergiobullitt4509 8 жыл бұрын
Can this be installed in a 01 bullitt. cuz the throttle body is different as the gts
@lilbroughdizzle
@lilbroughdizzle 9 жыл бұрын
I just installed this, and I noticed a large air almost a leak type of noise around the backside of it near the firewall.. But when you start the car up afterwards I can hear a similar sound... Is it normal or am I missing something here...
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
There shouldn't be any loud air noises so I would double check the fitting on the back of the unit as well as the vacuum lines.
@OmarGarcia-ol6yk
@OmarGarcia-ol6yk 9 жыл бұрын
I have a question why my check engine come on and the car field like wants to turn off
@Djuane
@Djuane 9 жыл бұрын
sounds like a vacuum leak somewhere
@OmarGarcia-ol6yk
@OmarGarcia-ol6yk 9 жыл бұрын
revelationns yes it sound like vacuum sometimes
@agencyheadquartersdc4568
@agencyheadquartersdc4568 8 жыл бұрын
the alt pulley can i use ratchet to remove the factory pulley thanks
@APorkchopGuy
@APorkchopGuy 2 жыл бұрын
Does anyone know where I could find the ratchet he has that folds
@asfgvjignbcguy8898
@asfgvjignbcguy8898 8 жыл бұрын
some old school guy told me if I put in a after market throttle body I have to do some thing with fule injections to get a balance is it true?
@Zerogivengarage
@Zerogivengarage 8 жыл бұрын
Nope not at all. Injector size is relative to horsepower, a throttle body swap does not provide a large enough gain for larger injectors to be needed.
@asfgvjignbcguy8898
@asfgvjignbcguy8898 8 жыл бұрын
Bill Tumas thanks bro
@hermanrogers1325
@hermanrogers1325 2 жыл бұрын
So the 78mm throttle body only works well with the 4v
@fairfax_fran5109
@fairfax_fran5109 Жыл бұрын
That’s what I heard I guess the stock 2v is 75mm and under
@joselikescars
@joselikescars 9 жыл бұрын
I'm sure this has been asked before, but i wanted to know what is the exhaust setup on the mustang at the end of the video?
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
+joselikescars BBK longtubes, BBK off road X pipe, Magnaflow cat back on a terminator swapped 96 Cobra.
@joselikescars
@joselikescars 9 жыл бұрын
Oh so it's a 4v, anyways it sounds good!
@drewbaglin1632
@drewbaglin1632 8 жыл бұрын
What cold air intake from y'all will work well with this?
@kevinleatherwood7823
@kevinleatherwood7823 3 жыл бұрын
This video does not say anything about which bolts to use to put back on the throttle cable bracket. He uses the factory one and doesn’t tighten all the way down. Why? Because you will 1. Break off the bolt head. And 2. The bolt will protrude through the plenum and ruin the plenum...you will need a new one. The LMR video is very specific about this part of the installation.
@kevinleatherwood7823
@kevinleatherwood7823 3 жыл бұрын
Missing that key detail screwed me. Pay attention to the LMR video on that portion to get it right.
@connormolson
@connormolson 9 жыл бұрын
I just finished installing this and my car is idling very rough. I tried adjusting the screw that you mentioned at the end of the video but with no luck, how can I fix this?
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
If you have a very rough idle I would guess you have a vacuum leak somewhere.
@SephiVX
@SephiVX 9 жыл бұрын
Or you might have a dirty iac calve
@benbandz165
@benbandz165 8 ай бұрын
That's the throttle sensor
@MichaelGsandup
@MichaelGsandup 7 жыл бұрын
They say don't go larger then a 70mm to 73mm on a stock motor so how are they doing this ???
@Zerogivengarage
@Zerogivengarage 7 жыл бұрын
You don't want to use a large throttle body with a stock plenum since the restriction will still be there, this is a one piece setup with the plenum so it will work fine.
@MichaelGsandup
@MichaelGsandup 7 жыл бұрын
Bill Tumas no I understand it's best with a matching bore plenum but I thought with a stock motor you could go bigger then a 70mm without losing power
@mitch9521
@mitch9521 9 жыл бұрын
ive seen people install these on 4.6L Panther cars too, but on them its probably overkill since they're tuned a bit different.
@abelvidronazario6433
@abelvidronazario6433 6 жыл бұрын
I have a 02gt 2v,bbk cai,x pipe with flowmaster,is 78mm good for my car setup?
@EricR_1
@EricR_1 4 жыл бұрын
Did you ever get it
@ExtremelystrongforJesus
@ExtremelystrongforJesus 10 жыл бұрын
Does it need hand tuner of will it just increase horse power?
@Zerogivengarage
@Zerogivengarage 10 жыл бұрын
Does not require a tune
@rjc757r
@rjc757r 9 жыл бұрын
Would this work on a 08 crown victoria p71 with the fly by wire throttle body?
@mitch9521
@mitch9521 9 жыл бұрын
Reginald Coleman Nope
@rjc757r
@rjc757r 9 жыл бұрын
Okay. Thanks.
@ivancedillo8
@ivancedillo8 4 жыл бұрын
Can I install this in my 04 grand marquis?? Pls say yes
@johndoeswork
@johndoeswork 4 жыл бұрын
Works for any 4.6L Ford engine, make and model of the car doesn't matter
@ivancedillo8
@ivancedillo8 4 жыл бұрын
John Casebere hell yea brother
@tavomorales2292
@tavomorales2292 9 жыл бұрын
The intake of the bullitt has a different shape would this fit my o1 bullitt ?
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
+Tavo Morales no The bullitt has a unique intake that uses an oval throttle body
@sergiobullitt4509
@sergiobullitt4509 8 жыл бұрын
+Bill Tumas thanks bill
@bayarea4898
@bayarea4898 7 жыл бұрын
1994 thunderbird 4.6 fits ????
@p51mustange1
@p51mustange1 9 жыл бұрын
Will this work on a 97 thunder bird with the 4.6 v8
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
p51mustange1 I never tried but its the same engine so I see no reason why it wouldn't
@mitch9521
@mitch9521 9 жыл бұрын
+p51mustange1 As long as it has the same intake manifold, it does not matter if the plenum faces to the passenger side(Mustangs) or to the drivers side(Crown Vics, Towncars, Grand Marquis, etc) it will bolt up fine.
@TheJordanobsession
@TheJordanobsession 9 жыл бұрын
Would this BBK TB work on a completely stock 01 GT?
@Zerogivengarage
@Zerogivengarage 9 жыл бұрын
TheJordanobsession Yes it will
@kustomkicks771
@kustomkicks771 3 жыл бұрын
Ok so you take out 5 mounting screws but only put 4 back in? Did you reuse a factory one? Lmao no one else? I received my BBK and they should def specify.
@TopMach1
@TopMach1 2 жыл бұрын
the stock throttle body looks cooler
@liltwist98
@liltwist98 7 жыл бұрын
i have a Dorman intake manifold. will this throttle body still fit my 04 GT
@Zerogivengarage
@Zerogivengarage 7 жыл бұрын
The dorman is a stock replacement so yes.
@TurboTurdBurglar
@TurboTurdBurglar 6 жыл бұрын
You loose a lot of power running the Dorman intakes
@Tommynator666xxx
@Tommynator666xxx 6 жыл бұрын
Dorman is trash. Dyno proven 12hp loss.
@MrAcat1988
@MrAcat1988 8 жыл бұрын
Does the bbk fit with the factory engine brace on a 97 cobra ?
@Zerogivengarage
@Zerogivengarage 8 жыл бұрын
+MrAcat1988 this is for a GT, it will not fit a Cobra
@HOTRODRICO
@HOTRODRICO 8 жыл бұрын
Mr. Tumas may I please ask you a question sir? I have a 97 cobra 4.6 4v dohc car and I was going to change my tps, is there anything in particular i need to do as far as physical adjustment like the fox bodys have to as far as setting it to below 1 ohm or letting the car re-learn the cars throttle position at idle, if so for how long and what about driving there after to teach the new tps? or are they more advanced and just plug and play in my vehicle ? thank you sir
@Zerogivengarage
@Zerogivengarage 8 жыл бұрын
The TPS should simply be plug and play for your Cobra
@HOTRODRICO
@HOTRODRICO 8 жыл бұрын
thank you, for your prompt reply sir, I appreciate the help
@chino.4.651
@chino.4.651 3 жыл бұрын
2021 I added the 78bbk tb on my car and it started idling rough rpms where at 3000 I adjusted the throttle screw and to get my rpms back down to 800-1000 range worked out pretty good but I noticed that when I would drive and push down on the clutch to go up or down a gear the rpms would shoot up and go down slowly not sure what’s the problem been dealing with it for weeks now any ideas!
@chino.4.651
@chino.4.651 3 жыл бұрын
Mods: Ford performance intake manifold Sr pulleys Msd coils K&n air intake Xpipe and no mufflers
@mr.burciaga2800
@mr.burciaga2800 3 жыл бұрын
Any luck on figuring out your problem? I recently installed same tb and getting same results as u.
@fairfax_fran5109
@fairfax_fran5109 Жыл бұрын
I was interested in purchasing but after reading the comments there’s no positive results 😂
@Scottypowpow
@Scottypowpow 10 жыл бұрын
If I put this on my car would it mess up my air:fuel ratio and have to change anything else? What if I put this on my stock motor
@Zerogivengarage
@Zerogivengarage 10 жыл бұрын
It is perfectly safe for use on a stock motor with no other changes.
@stevencanales1748
@stevencanales1748 8 жыл бұрын
can this work on 2000 crown vic
@MrBamafan2570
@MrBamafan2570 8 жыл бұрын
Can I put this on without a tune?
@traplordx5645
@traplordx5645 5 жыл бұрын
is it possible to put headers on an automatic gt?
@cjponyparts
@cjponyparts 5 жыл бұрын
YEs we have headers that will work with autos
@sebastiancastaneda1715
@sebastiancastaneda1715 3 жыл бұрын
4:58😂
@Tommynator666xxx
@Tommynator666xxx 6 жыл бұрын
I cant believe you're telling people 78mm goes on a stock 4.6 and does something. 78mm is way too big for a stock or lightly modded car. 78mm is for boost. Dont believe me? Join some forums. Do some research.
@TurboTurdBurglar
@TurboTurdBurglar 6 жыл бұрын
Tommynator666xxx have you actually done this mod to your car? I have it on my bolt on 02 gt and you can definitely feel a difference in throttle response and in power
@SGTRacing
@SGTRacing 5 жыл бұрын
Im going boost. But for now i will be a bolt on car with this 78mm. Installing it all soon so ill get back. I had a car with 75mm so it will be interesting to see what the difference is.
@TurboTurdBurglar
@TurboTurdBurglar 5 жыл бұрын
SGTR 3 mm isint much for a difference from 75 but when I went from stock to the 78mm I noticed a nice increase in power and torque it’s the Best mod I’ve done to my car I also have gears and full bolt ons
@SGTRacing
@SGTRacing 5 жыл бұрын
@@TurboTurdBurglar my last car had the 75mm. Current car will have the 78mm. Alot have been saying you lose. So im going to test this theory since i wont be boosted for a few months
@TurboTurdBurglar
@TurboTurdBurglar 5 жыл бұрын
SGTR the only people who say that are people who haven’t tried it. Maybe to much for a npi but I was worried like you but I Got a good deal on a 78mm bbk and was impressed. Make sure you get a big enough intake that matches the diameter of the throttle to get the full effect. Also make sure you are not running a dorman intake as well which will limit your flow
@joselikescars
@joselikescars 9 жыл бұрын
I'm sure this has been asked before, but i wanted to know what is the exhaust setup on the mustang at the end of the video?
@JM-uw1wg
@JM-uw1wg 5 жыл бұрын
joselikescars bassani x pipe
@danielbeaulieu5165
@danielbeaulieu5165 3 жыл бұрын
I didn’t get a supplied bushing for tps valve. Is it necessary?
@danielbeaulieu5165
@danielbeaulieu5165 3 жыл бұрын
Also My base idle won’t drop under 1000 rpm and my idle screw is backed right off
Mustang GT Throttle Body & Plenum Install & Dyno (96-04 4.6L)
5:26
Late Model Restoration (LMR)
Рет қаралды 111 М.
1999-2000 Mustang V6 BBK 65mm Throttle Body Review & Install
7:41
AmericanMuscle Mustang
Рет қаралды 52 М.
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
36:55
bayGUYS
Рет қаралды 1,9 МЛН
Cheap & Easy Mod to Make Your Mustang FASTER!| BBK intake plenum | 25hp
9:53
Mustang GT BBK Throttle Body & Plenum Install (1996-2004 4.6L 2v)
4:18
Late Model Restoration (LMR)
Рет қаралды 71 М.
1996-2004 Mustang SR Performance Cold Air Intake Review & Install
17:39
AmericanMuscle Mustang
Рет қаралды 12 М.
How To Clean The Throttle Body-Without Removing It From The Engine
8:48
All Show and NO GO? 1994-2004 Ford Mustang GT 4.6 Performance Upgrades!
40:53
Rainman Ray's Repairs
Рет қаралды 175 М.
2005-2010 Mustang GT Ford Performance Twin 62mm Throttle Body Review & Install
9:49
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН