My new DC Power Supply -WANPTEK WPS305H

Hello, this is my new Adjustable DC Power Supply (30V 5A) . This is WANPTEK WPS305H , high precision DC Power supply with multiple protection. It looks great, nice ,compact and easy to use.
You can buy it here:
www.banggood.com/custlink/DvG...
If You want , You can support this channel. Here you can buy me coffe.
ko-fi.com/volosprojects
Thank You!
Black Friday Deals 2021 bit.ly/3wGaMk7
CLEARANCE sales bit.ly/3DbNlRU
Auto & Moto,Tools & Electronics sales bit.ly/3c2MEOW
Big Brands New Arrival bit.ly/3qxSAbc
Crazy Coupon Deals & Best Offers bit.ly/30gtTFG

[@Peter_Cetera]

Very smart, to hold your hand in FRONT of the display, you will show...

[@MakerFabio]

I also have the riden 6018 and start to be tired of pressing buttons. Maybe i don t like to have to adjust current initially at 10mA digit I want knobs. Thanks fos sharing

[@electronic7979]

Excellent product

[@minmax12345]

Ottimo ho preso il modello da 10 ampere encoder precisi con regolazione anche fine dei valori

[@panospapadimitriou3498]

by mistake i ordered this small one without fines i thought i had the 60v or the 30v10a one at 300watts.. anyway i m amateur and want it mostly for single charge cells and top balace em.. comonly 20/25 amps cells !!! hope with some patience this 150Watts will be ok

[@minmax12345]

Fantastic, arrive today, it's incredible

[@crlos_henrique]

Hello friend. Is it still working fine? Did you have a problem with her? I'm Brazilian :D

[@lupoal4113]

ok... what about ripple? what about electrical noise?

[@theshepard22]

Will the amperage go down (while the output is on) if the device isn't connected to something that can receive the power? I tried connecting some lifepo4s to a model just like this and the amperage would always drop out to zero when I would adjust it on the output, even though it was all connected to the battery. 🤷 Thanks for any help u can give!

[@EasyOne]

nice

[@PAFriedel]

Hello, does it memorizes voltage and current when power down and off? Or do you have to set it at each startup ? Thanks

[@meguinness1116]

Will it do constant voltage and constant current? Ta

[@Flavius-Tech]

Can you put power in a shorted pcb to see what is going hot and find faulty shorted component?

[@adredy]

Faster than old model looks ok on bangod cost 75 but on ali only 45£ :/

[@samuelrojascortes3782]

Gentlemen can you share the brand for your Multimeter in this video and the model number? Thanks in advance!

[@Druidus98]

It’s visible in the video: Aneng AN-999S

[@heinztimmer5453]

The Original Manufacturer is Zotech with its brand Zoyi, but you can find it as a rebranded one from Aneng, Bside or Richmeter. Exists 3 or 4 models, but on all rebranded one they are exactly the same.

[@dononeill1256]

Hi, I'm not getting any continunity reading on the power bench when I put multimeter probes and crocidile clip together. Any idea why, thanks.

[@peterspiegelenburg4262]

Can you disable the beep you hear when turning the knobs?

[@danijel124]

Desolder the beeper on the pcb. I made the same with several ups units

[@Dsbarrynl]

No, i have seen an aliexpress video where you have to press and hold a knob and you can set luminescity of the display and beep sounds.

[@marpra]

jel još uvijek radi, nakon 2 godine . pozz

[@VolosProjects]

da, radi bez greske, ne palim ga cesto ali jos uvijek radi

[@14kukucka]

Kad si već iz HR. Jel bilo carine?

[@VolosProjects]

Nije, slali su iz eu skladista

[@Sycu]

"This way i can be much faster", then it took literally 15 seconds to set the voltage to 3.5V :D

[@GlennMartinez]

I bought it! Confused, no manual! says get on line, no link and cannot find! Shipped showing 230volt on cord connection, just as yours is showing, it in 110 Volt connection when showing 220 or do I need to slide over to be 110 volt in America. Are you running 230 or 110volt. I set it for 30 volt and it lowers the voltage! I want constant voltage and limit the current. odd set up.

[@VolosProjects]

it need to be set like voltage in your country, my is set to 230. (230 is visible) .

[@ChupoCro]

When Constant Current mode is ON then of course voltage has to go down - how could the power supply otherwise limit the current? You can't change the Ohm's law. Try setting 25 V and 200 mA and then short the leads. CC LED will be ON and the voltage on the display would be 200 mA times resistance of the leads. You can't have higher voltage than current times resistance. BTW, I've found the manual in just a few seconds.

[@urnoob5528]

I'm more confused reading wtf u sayin

[@corel965]

Wait is this linear or switching psu ?

[@urnoob5528]

Should be obvious

[@Dinco422]

2:00 lol... are you american or something ? measuring things with everything but a ruller xD

[@ooltimu]

Can you use it at more than 5 amps when the voltage is lower than 30V? For example 10V 15A?

[@user-hp1xs6jp4z]

Of course not

[@ooltimu]

@@user-hp1xs6jp4z why? it would be nice

[@corel965]

@@ooltimu max is 5A out...

[@stark_energy]

@@ooltimuthis is lab bench power supply, which often not require to do more than 5A, if you need to power something greater than 5A this isn't the right tool because this tool is for diagnostic and testing small devices that need accuracy over big amps. You can buy a cheap 12V power supply with 40A and then step it up or down as you like if you need just big current without much accuracy.

[@urnoob5528]

5a is cc limit duh

[@moturcu4226]

Hi are you still happy with Power Supply?