How to make Electric Stove

[@marcelod.tallon9438]

Excelente!!! Muchas Gracias!!! Saludos desde Argentina

[@budspencer.hussam7481]

We used to make this heater in the early eighties and mid nineties of the last century. We used to come with a thermistor block and start digging this block piece and put the heater wire in it and then connect it to hot and cold electrodes and then connect it with a cable to electricity

[@aijazahmed9113]

You have nice idea but you should also protect the L and N screw by mistake it is harmful and dangerous you can protect with plaster of Paris.

[@jabwel]

That is the exact method used in making hot plates but he needed to cover the coil with insulating cement to prevent shocking. Because any contact with the coil could be so disastrous, and may lead to death

[@eduardmrva3762]

Don´t to this stove, people. One touch with a hand or the metal cooking utensil/spoon or metal stirring equipment to that unfused, exposed heating element and you are dead. Neither your body, neither the tin body of the stove will most likely lower the resistance so that the circuit fuse for that power line will break and it will fry you alive with 4-8A, depending if your mains is 250 or 120V. Your hand, burned through by the heat from the element will be your smallest problem, then.

[@esser7678]

Karen, Keep Away🤣🤣

[@thathajeong6426]

HipJam

[@ajmalmeran6613]

@@esser7678 he is right actually.

[@metalmaniak2011]

Go Walmart and buy one , let's do it by ourselves. Bye Karen.

[@janukebabukabuddy]

Solution": use wood element, or switch off the component ,and wore gloves......

[@milanoseduworld7921]

In olden days it was used widely. When i was small we had in our house. No problems were found.

[@juantovar731]

Very resourceful and practical. Congratulations.

[@abhajihadi]

Takes 4.6 amps Almost near a 1 ton ac amps. 😳 Thanks for sharing

[@keith_ferdinanduz]

Good. This is a recreation of old style hot plate. But Plaster of Paris will crack and crumble in time.

[@emanmahamd1787]

هذه افضل طريقه لتسخين كوب من الشاي على الكهرباء واتمنى ان يكون هناك المزيد من الابقار العبقريه كهذه الفكره وشكرا لكم👍🤙🖐😐

[@ИванКопец-б6ы]

В моём детстве такие (,один в один) электроплитки были у всех,стоили не дорого.(мне 71 )

[@jozngallyzzoforex]

@jozngallyzzokzbin.info/www/bejne/sJKafXpmYpaNsK8si=HTs96veOGsg2c3a3

[@jeetsaini143]

The best palace to use this sotve where the electricity is free.

[@Bittutv2003]

Ha bhai

[@SuperSchnelle]

welcome to Venezuela!!!!

[@claapitan]

welcome to phillipines 😂

[@themysticshadow6688]

I though it wasnt a palace i thought it was a country @@claapitan

[@themysticshadow6688]

@@claapitan nvm im dumb

[@premarathnagagabada5518]

හොඳ වීඩියෝ එකක් ඔබට ස්තුතිය්

[@lemmabaruda5035]

Yes Man,The skilled professional person.Thank You

[@raajsuman1292]

Superb idea, thanks.

[@CarlosTorres-hk5tp]

genial amigo gracias por enseñar su sabiduría así aprendemos saludos desde venezuela muy bien amigo la voy hacer

[@nautankinachgana1986]

Aaise hi log se mai bahut hi empress hu kuch new Idia layo thanks

[@andersondasilvapaz7079]

adorei o projeto e ainda mais os sulcos para a distribuição da resistência.

[@zelalemworkineh3433]

really good the materials u are used are easy and not costy I don't know the material that u are used as a power is that is cement?

[@alanjagroop1282]

Could this stove be used as a mini table top furnace.

[@chetanyt5544]

Sir garme laga sakte he 240v se jalega

[@riverman4798]

Sweet.. Your video editing kung fu is strong. Thanks for the entertainment.

[@HailuLenjiso-v2k]

Thank you for sharing your knowledge.

[@andrewebmaster5376]

lo que yo quiero saber es cual es el tiempo que toma en llegar al tiempo de ebullicion esa taza de te...para poder saber algo acerca de la efectividad de tal estufa... ya que si tengo que esperar una hora por un te creo que hay que pensarlo dos veces antes de gastar tanta energia en eso, o mejorarla... saludos amigos

[@rahulmane9057]

Great Work........ Amazing Idea

[@alanjagroop1282]

Could it be used to melt metal. Aluminum cans and more

[@budspencer.hussam7481]

Good job 👍👍👍 this idea we was made it in 80s and in 90s from 20santury

[@JosepheBatembe]

C'est magnifique cette demonstration

[@kyme32]

you should have secured that heating wire to the clay with some U form hooks, it can pop and your metal pot become live

[@silvane_silva]

Parabéns! Ótimo trabalho 👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾

[@quinta-coluna8746]

Isso é fake ele errou feio

[@Sethlondon19930]

Would probably be better to cover with stovetop glass so you dont risk a boiling over pot spilling into 220V or accidentally pushing the grate into 220v which would essentially be like stuffing a fork in a toaster.

[@dschannel1171]

And could attach a earth wire on metal body too.

[@deserteagleiii1643]

Its safe.. the power source is isolated.. and electrical energy is converted to heat energy so even if the pan is incontact with the heating element it will just get hot.. the only things thats missing is the one that controls the heat so that it could last long..

[@bundaernianti6121]

Subhanallah that is cool idea man......👏👏👏👏👏👏

[@factsreality13]

And finally the TEA stole my heart...

[@prashantambati1304]

It's taking amps how much

[@klemersonbosque4320]

- mui bom

[@jimmyimperial6127]

That's god job Vaibhav also I send you god feddback , my name is jimmy from México state Guanajuato.

[@angelveloza5693]

🎫🎫🎫🎫🎫🎫🎫🎫🎫🎫🎫🎫🎫👨👨👨👨👨👨👨👨👨👨👨👨👴👴👴👴👴👴👴👴👴👴👴👴👴👴🎅🎅🎅🎅🎅🎅🎅🎅🎅🎅🎅🎅🎅👶👶👶👶👶👶👶👶👶👶👶👶👶🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏👥👥👥👥👥👥👥👥👥👥👥👥👥🖑🖑🖑🖑🖑🖑🖑🖑🖑🖑🖑🖑👊👊👊👊👊👊👊👊👊👊👊👊👊👊👄👄👄👄👄👄👄👄👄👄👄👄👄👐👐👐👐👐👐👐👐👐👐👐👐👐💅💅💅💅💅💅💅💅💅💅💅💅💅👅👅👅👅👅👅👅👅👅👅👅👅👅👅💑💑💑💑💑💑💑💑💑💑💑💑🍔🍔🍔🍔🍔🍔🍔🍔🍔🍔🍔🍔

[@markc1894]

I will be thinking of making a better grate yours doesn’t look very stable but still very good idea

[@maths_lab_]

How much consumption of electricity it?

[@arelysjg7197]

BUENAS TARDE, QUE TIPO DE MATERIAL UTILIZO PARA HACER LA PASTA QUE INTRODUJO EN LA BASE DE METAL, ERA YESO, CEMENTO U OTRO MATERIAL? GRACIAS

[@kisangadekar5625]

Thank you sir, Khup chhan video

[@albertoorozco682]

Hellow, it's very good, how is the resistance name?

[@prioputro4111]

Thanks for ideas, so good profesionally job.

[@noelgreenchikezieokezie8488]

Thanks, nice work, but which other cement that can be use other than the pastry cement used here cos in some countries and are one can't get exactly the one you used. In my country, we have cement for building and white cement for pop ceilings

[@mikaelmyers]

Eu acho que e gesso !

[@gunupurumanoj5357]

Sir heating element 220 1000 w will you use, you say for my answer

[@sangharshmore1494]

Can we plug in it into normal switch as it can melt the button or switch board due to high voltage

[@HiraKVlog]

Is its save to use

[@johannlygiron4526]

ese material es yeso o cemento y uno puede hacer la resistencia con alambre

[@anusakram2849]

Bht zbrdst yrrr

[@hagajen]

Super tecnic bro

[@Rendraled]

How to calculate it nicheome wire for 220v supply

[@shiamsarder5265]

Nice broooooooooo.💖💖💖💖💖💖🙂🙂🙂🙂🙂🙂🙂from Bangladesh.💖💖💖😄😄😄👌👌👌🤠🤠🤠🤠😎

[@mundodigital467]

este consumo 1000 watts é dequanto tempo. por hora por mes ?

[@douglasfernandes7097]

Por hora

[@mundodigital467]

Bora tentar fazer as contas aqui.. por coincidencia a lição de meu filho fala sobre como calcular o gasto de certo aparelho por wats... assim de cabeça deve ser : tipo FERRO ELÉTRICO AUTOMÁTICO 1000 12,00 por mês só ele.

[@airconputerTV]

Nice but this is dangerous to people when accidentally touch the stove because this is considered as live wire right?

[@adnanbaloch1484]

I agreed wirh u coz its not safe,dangerous too much live current,there is no safety ,work done very well but risky

[@lookoutleo]

so thats how you make chai :) and intereting project , would be good to make 12v version for my van

[@dschannel1171]

Man, 1000W on 12V is about 83A, can really your battery handle this for a long time?

[@lookoutleo]

@@dschannel1171 I have a home made 12v one , it draws about 15a 12v , boils kettle in 15 mins , Frye's an egg about 5 mins. Made out of parts of tumble dryer hrater

[@zack9633]

can this be made so it is powered by 12 volts DC?

[@letusinvestmints3178]

Could you send the website where I could buy the heating element (the coil)?

[@tumadre606]

You're better off buying a electric cooker for cheaper...

[@cientistalima2010]

Excelente! Só um cuidado para estes terminais não causar curto-circuito.

[@dschannel1171]

Está faltando um aterramento e um circuito específico para esse fogão de forma que qualquer curto-circuito entre os terminais ou com um terminal e a carcaça desligue o disjuntor. Se for usar uma extensão, que seja específica para esse fogão, com um disjuntor bipolar pois mesmo no monofásico não há garantia de que a tomada tenha sido instalada sem estar invertido fase e neutro, e tenha aterramento para caso uma fase encoste na carcaça o disjuntor se desligue.

[@romilsonmagalhaes6487]

O cara usou gesso! kkkkkkkkk

[@frankvargas9595]

THANKS YOU MY BROTHER FROM VENEZUELA.

[@aliriobenavidesvalencia1793]

Lo felicito bien feliz año nuevo mister Ford gracias.

[@GabrielA-wc4hp]

Pregunta! Se podría hacer una de 12 v cc. Con batería de carro? También olla para coser pero con 12 v.?

[@themysticshadow6688]

cuanto yeso usaste?

[@amazingandrealtyoflife4046]

Osmmm work

[@vedamurthisubramaniam2494]

neat & clean job thanks bro.

[@blockedinchina6015]

Clean my ass!

[@albertoorozco682]

Excelente, muy buena, cómo se llama la resistencia

[@speedfight49]

Nice, would it be possible to have the link for the component used in the video. This could help for the future to manufacture for the interested person it is a suggestion that can be useful 😉

[@kurangturu4754]

Is it savety?

[@katherinemeroalvarez3669]

Mi brot xq no nos esplica con tu voz yaq nos serbiria d mucha ayuda y mas fasil . Gracias y sigue asi t fefisito ??? 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@TheSalemSaberhagen]

Ty vole, tak tohle je už moc i na mě! Ochrana před úrazem elektrickým proudem asi pánovi nic neříká. Vařiče s otevřenou topnou spirálo se u nás dělali v padesátých letech. Jeden mám doma schovaný po opravě, abych mohl ukazovat, co se dřív používalo. Ale i ten je bezpečnější než tohle.Tenhle výrobek bych si nedovolil provozovat ani v laboratorních podmínkách s dielektrickými rukavicemi. Jen by mě moc zajímalo ve které zemi žije tenhle "šikula".

[@ninapolancopolanco9866]

Muy bueno. Felicitaciones!

[@harshsparikh]

Hi what do you call the green pad or mat underneath the electric stove? I want to order one but dont know the technical term. Thanks

[@MyProjectsLab]

Green pad called cutting matt.

[@Rhaviston-Silva]

parabéns mano. ajudou e muito.

[@muhammadzamanahmad8223]

Can size? Please bata den k agar ye ham ghar pe banayen to kya safety measures uthayen aur kin baaton ka khayal rakhen?

[@dagnydagnydagny165]

Donde puedo conseguir esas recistencia o de que material es?

[@diegzvxh7178]

Tal ves en ferreterías pero solo que es en tira pero se se puede dar forma😀

[@khelladiful]

I also learned the new coffee recipe

[@kartarrathod9622]

What soil should be use in This?

[@SurendraPaswan-je6vg]

Ye POP se banae hai. Heat hone per toot jaega. Fer kya hoga.

[@ulisescarrillo2373]

Exelente, oye hermano como se llama ese aparato que aparece en el minuto 10:23

[@georgemlhuid5539]

Who is heavier plaster of paris or cement

[@ErrolPlayerist]

Is it possible to run this in a battery and a 12 to 220v inverter?😊

[@julianvalenti]

You got me until you cut the can arround the power input! Very nice project!

[@dariomilesevic6789]

This is PERFECT 👍👍👍👍👍👍👍

[@Paulzm1]

How do you measure Temperature? I need a low setting to cook Rice

[@eyemovie824]

30 min of cooking how much electricity unit it takes

[@shahbazawan7939]

Bhi plaster khan se mile ga

[@treasureoflife5351]

Can I place stone or brick beneath the stove?

[@PravinKumar-wg9zj]

What's about electricity bill?

[@fununlimited526]

Is it working on 12 volt also.?

[@priyankadash3821]

Mor jaogi

[@georgevasile1095]

It can be seen that in some places, the resistance is stronger, there it will burn you. Before stretching the resistance, you must measure the channel with a piece of thread. Measure the resistance after that piece of thread and then put it on the channel, so that it will be uniform in length and will radiate heat evenly.

[@alyamama8193]

ماشاءالله بالتوفيق سوداني مره من هنا

[@shortsvideos9812]

😂😂😂😂😂😁😂😂😂 منور

[@Mr_Ravee]

Ok 😎Now i need to figure out how to generate electricity in the middle of nowhere😈

[@femorapaz49]

Que es plaster of parís? Con eso hizo la mezcla y se supone que resiste la temperatura. Quién me puede informar ? Gracias.

[@fierrosoft]

Yeso= plaster of paris

[@candytrace3337]

Is it safe ?

[@vikasanchanh.n2055]

Wher did we get that steel cylinder

[@lorddiosliving]

So easy to make at home yourself...( you only have to get some components in the china black market) ...but still very easy

[@varshawilson228]

Can you make a stove using fire wood as fuel , convert heat energy in to electrical energy and can charge electrical appliance while cooking

[@bodiminds6571]

It is possible with a thermoelectric circuit

[@ImprovediaTV]

Good idea...

[@SMARTEK-INFO]

What is the name of the coil can I use 12v to power it

[@mdsikdarsaiful1610]

is it possible with dc 12v

[@dschannel1171]

Yeah it is, but it will get 83A of battery, and you will need a at least 1700A battery bank to work well without discharging fast.

[@kartarrathod9622]

Plaster of paris ke mold me current nahi lagta kya bhai koi batao please

[@fedrickjoshuachinonyerem9413]

What is the name of the heating material

[@sfsongbox2972]

Kitina ward k element leghna hy

[@pramodshukla7290]

Very nice 👍🙏

[@bivaskarmakar7800]

How much ampere load is used to connection ?

[@franzdanielalapide2307]

Exactly 5amps .. for surely 20 amps