N Machine....Bruce Depalma..Faraday Research RND

[@rollmeister]

I tried building one as a teen. 2x rare earth disk magnet about 4inches in diameter and a hard drive platter disk in between I spun it using a drill, poorly, and got about 80 millivolts. I gave up on it. You need at least 12inches diameter to get about 1volt. You can put them in series on the same axle (that insulates pairs of disk centres from each other) to get more voltage which also lets you use 2 disks for each magnet in the middle.

[@JK-zl7vv]

FINALLY, someone showed the amp readings on their generator, for some reason all the other videos are showing people just reading voltage on their machine, but this type of machine is not known for voltage output, so I never ubderstood why they keep showing just the voltage readings, but today I found this video and so good for you for properly testing your project. 😁👍

[@CharaTR]

By the way... should you try the machine in different environments? After all, we know how it works and that it works efficiently if upgraded correctly. but we don't know what the variables and unscientific are. Or what does it react to or what affects its electrical output? In this way, we can have more data about what happened. For example, try it in an area with less light and see if the current drops.

[@Aboudy1989]

use resonant transformer with slayer exciter circuit it works as autotuner to convert those high amps into high voltage then rectify and filter the L2 into pure DC current, then connect it into any solar inverter into the PV Input. There you go you have Over Unity of multiple KW's with only Few Watts of input. result of Mixing N- Machine with Don Smith generator

[@o5you86]

Bruce De Palmer went to Auckland New Zealand & he built a similar N Machine to yours with both North Poles facing outwards. He used something he called a ‘Compensation Field ‘ which was said to compensate against Drag caused by Energy withdrawal. De Palmer quoted that it was ‘Equal in Amplitude, Opposite in Sign’. I build Stanley Meyer Water Fuel Cells that requires a ‘Choke Coil’ which is the same thing in that it uses Opposing Magnetic Fields to restrict Amperage that prevents the Water from Detonating as this creates Shock Waves within the Water Fuel Cell but, it doesn’t work without these Choke Coils. Apparently if you hook up a load to the N Machine it creates drag & the Compensation Coil cancels out this Drag. I seen models of N Machines in Darwin with compensation coils & the Kiwi’s that showed me these said they were over unity by around 600%. Bruce De Palmer died in Auckland & his story is just Sad, similarly Stanley Meyer with his Water Fuel Cell was persecuted by Governments the world over but fortunately he went to Auckland New Zealand & shared his knowledge, all of which is very interesting & it seems all the citizens of the different Territories of the entire World are merely Economic Slaves born to be Cogs that keep the global economic machine turning.

[@wolfforce3740]

Hi, can you give some hints what "choke coil" design one should use on N Machine? Any links/ sources on that subject?

[@o5you86]

@@wolfforce3740 The Choke Coil on a Stanley Meyer Water Fuel Cell restricts Current from flowing prevent the Water from detonating. In the N Machine, once you attempt to draw Power from the N Machine the Rotor Assembly acts as a giant Brake similar to how Electromagnetic Braking works on a Train, the ‘Compensation Coil’ on the N Machine is a stationary External Stator Coil that works the same a Choke Coil but, because the Rotor Coil is moving & drawing Energy directly from Space the ‘Compensation Coil’ actually Cancels Out the Magnetic Field created by Energy Withdrawal preventing the N Machine from acting like an Electromagnetic Brake as in the Train Braking example. Also somehow the N Machine accelerates, I don’t know the mechanism that causes this but it nonetheless accelerates spinning Faster. The N Machine is such a fascinating device!

[@wolfforce3740]

@@o5you86 Thanks for you input! Do you mean that it would be good to use generic inductor type choke in the generator output as a back EMF filter? There are circulating a modified schematics of N-Machine that has AC output. It has 2 brush on the rotor edge in 90 degree angle. Do you have any experience with any kind of AC homopolar generator?

[@o5you86]

@@wolfforce3740 The table top N Machine I saw in Darwin was similar to yours but, was two seperate Disks the size of Music CD’s rotating on a central shaft with contact Brushes on nearly the entire circumference of the outer disks with the Negative being the centre shaft connecting the 2X rotating Disks. On the outside of these Disks was a Coil that looked like a 🍩 doughnut surrounding the Disks but not touching them. Apparently these created an opposing Field that canceled out the Magnetic Field Current created by Energy withdrawal. My understanding was that if you removed the outer 🍩 Compensation Coil any attempt to extract Current from the N Machine and it would act like an Electromagnetic Brake slowing down the N Machine. The Compensation Coil allows you to draw Current directly from surrounding Space without any drag.. I saw another Machine in a different configuration that looked like two stacks of Neodymium Magnets at right angles to each other ‘+’set in a Plastic Resin with a Coil Wound on the outer rim. This also had an external ‘Compensation Coil’ & looked like Tesla original ‘Induction Motor’ on its side view. When in motion these Machines appear to Accelerate on their own. Its really interesting & my opinion is that these Machines are actually replications of ‘Old World’ Machines that were found from another civilisation, & a couple hundred years ago we didn’t understand them. It looks suspicious & something is happening where all the really ‘Cool’ Technology is hidden from the mainstream knowledge base and we’re only allowed to have Technology that continues to enslave us? I think all of this stuff is like a rabbit hole!

[@FaradayResearch]

Yep I totally agree with you. This stuff is definitely when you get into it. You're going down a rabbit hole big time and it's a long drop. And yes, a lot of this technology has been hidden from us for at least 100 years or longer. But I continue by research and a lot of great points you've noted to me in your comments. Thank you very much

[@chaorrottai]

There's another way to get the voltage up, make multiple sets of two disks and put them in series.

[@1critical.truther]

Real science! I love it. Goodluck with everything!

[@user-tn1hk6zm2freedom]

Build a small DC generator that make volts and low amps on the same shaft and put the volt to the output using high amp diodes. You would have the volts and the amps mixed. Something to try? This is interesting.

[@FaradayResearch]

I've already tried that theory. It doesn't work. The voltage has to be stepped up after the device

[@FaradayResearch]

I stopped working on that project 2 years ago. I'm working on another stuff right now. That's my focus

[@ronarmstrong835]

Interesting in that the South poles are facing inward. When you subject seeds to the South pole of a magnet, they grow at an accelerated pace.

[@FaradayResearch]

I've tried all configurations and the best method that I've found is North pole's facing out southpole's facing in

[@CharaTR]

​@@FaradayResearchIf no one has patented anything extra in this Bruce de Palma project, can I understand and spread the solution to the problems? Is this possible?

[@FaradayResearch]

Any free energy device will never be patented. It will always be seized or they will deem it National security and you'll never see it ever again. Patenting is a total waste time and money you have to open source

[@CharaTR]

@@FaradayResearch I don't mean how it works or making your own version to sell and spread it. Otherwise, you are right. If someone doesn't spread it, this technology will die..

[@CharaTR]

@@FaradayResearch What if the machine gets power from an unknown particle or an unknown particle in the uncertainty principle? is it possible?

[@Naomi_Boyd]

Try adding oxygen. I bet the amps go up if O2 concentration around the magnets increases. I'm pretty sure it's just using air to generate the charge. O2 is highly paramagnetic.

[@smokyatgroups]

Thanks for sharing your work. Perhaps you can find a way to interrupt the current from the brushes? Then you could step up your voltage using turns ratio via a current transformer.

[@FaradayResearch]

Hi. Thanks for the ideas I will keep that in mind...cheers

[@FaradayResearch]

I seen an interview with Eric Dollard.... he did back about 10 years ago .. and he said he knew Bruce DePalma personally... and that the N machine was Not overunity... and the original machine was not designed by Bruce de Palma... it was designed by some guys I believe in silicone valley it was called the Starburst machine ...so as far as the overunity I haven't really pursued it because of the scale... The scale was way too small to get anything usable out of it....now if I scale it up to a point where the unit is by the 1,000 lb of magnets that I might have some useful power but this small bench top model just will not put out the power I need Mike

[@zekeriasvarg530]

@@FaradayResearch if you check Searl and think of ball bearings and stop listenting to the shills.. Searl are payed and bought for to, but not what he did. ( Thats not on the internet)...

[@CharaTR]

​@@FaradayResearchPeople are not developing it enough. They should get to the root of the problem. They should find out how this traction in space happens, understand the logic and build a simpler but functional machine.

[@FaradayResearch]

@@CharaTR Yes you are very right on that statement. That machine has not been explored enough by inventors like myself very often. I have some new ideas that I'd like to do, but I have so many projects on the table right now. It's not really in my view at this point.

[@make425]

Glad to see people looking into this tech. And i thought the same thing about mixing the current. I found it interesting that the magnets can be attached to the copper and spun as one. And still produces current. Or the fact that a spinning cilinder of copper will repell north and south, but will coexist with both fields, if the magnet is turned sideways.

[@FaradayResearch]

Hi yes this is very true what you have said the main important thing to remember is electromagnetism will always create a lenz effect or a resistance so in the... N machine the magnet has to be spinning with a copper wheel at the same speed either in the same direction if you were to spend a copper wheel with magnets on either side this will create lens effect thus creating a resistance you get cavitational forces on either side of the copper wheel that's what Michael Faraday discovered when he made his first faraday disc... but when you spend two magnets side by side these forces do not exist anymore so the big question is what is creating the current?? and I think the lines of force in conjunction with longitudinal lines of force within the Earth react with the magnets spinning this is just a theory ...but it makes sense when you think about it but anyways yeah the best thing to do is set up your own experiments and test everything every combination you can come up with try it that's all part of the learning process I spent well over a year getting to the point where I had a good working device where I can create 20 amps with just spending two magnets side by side thank you for your insights... cheers

[@zekeriasvarg530]

@@FaradayResearch study ball bearing engine

[@o5you86]

Also Tesla used 5 curved Partitions on his Discs that increased the Voltages & Tesla called it the Unipolar Dynamo.

[@elmultimediaschoolofartscu3924]

It would have been nice to show how you built it in practice so that we can add inputs and u save yourself pressure, so many great minds on the comments but it's not clear k😊😊😊

[@grahamfoulkes7321]

Would have liked to see the shunt on the back of the ammeter. All the demonstrations I have seen leave out some detail that would lessen my skepticism. To measure 20 amps at a few millivolts takes a lot more than a couple of croc clips, thin wire and a moving coil meter, basic Ohms law cannot be violated.

[@8thsinner]

If you have the magnets producing amps from an already rotating axle, why not load a different part of the axle with another motor arranged as a generator, and use the voltage form that? Or some kind of ballast or spark gap arc generator to create the voltage you want? Or maybe even a flywheel generator set up? A heavy flywheel could be rigged up to wind or water systems and with a magnetic gear array to generate very high rpms and clearly then very high amps.. Just thinking out loud here...

[@FaradayResearch]

This project I was working on over 2 years ago. I'm no longer working on this project. I have other things on the go right now

[@8thsinner]

@@FaradayResearch I noticed. Still working through your vids...

[@marwansallouta2101]

Very nice, thank you. I think you did not hit a roadblock yet. Can you try to heat up a small amount of water (cup of water with thermometer) using the (22 Ampers output).

[@sidster64]

It's free information. I share Thanks again great video

[@innovationsforall]

How about gluing loops of isolated adhesive copper foil around the magnets (whole magnet height) and try to measure the voltage? Btw, maybe this phenomena is connected to some lagging between matter inertia and flux inertia (if such thing exists)...

[@8thsinner]

Did you glue these against a strong repulsion from each other? Or are the magnets just kept at a comfortable distance from each other and not forced together? I would imagine the closer they are together, the more of an effect there would be. Not sure which effect but I'm sure it effects things. Did you test this concept yourself in prototyping?

[@jacktherip7750]

WOW

[@fxeconomist]

I think there is a way to increase voltage. I would like to have one built for myself here in UK. My idea would be to replace the Faraday disk with a spiral coil. This would allow it to stay in contact with the brushes, but have the shaft made non-metallic. Then pulse DC thru the moving spiral coil. Collect the high voltage back EMF along with the amps... Alternatively, keep it unipolar. Have one magnet move at the same time with the coil, on the shaft, and have the outer magnet stationary, but exposing both poles to the coil. This should allow to have voltage induced at the same time, but probably will cost amps.

[@FaradayResearch]

I would make a prototype and test these concepts....get on the bench and make it.... that's what I do

[@fxeconomist]

@@FaradayResearch That would be absolutely brilliant. But remember, the copper coil would needs to be insulated from the shaft. I don't know if your long shaft is actually insulated from the short motor shaft. I think you can get a solid copper pancake coil just enough for a short test, but it will be difficult, because your machine is enclosed in the big case. If you need I can study how to code one in OpenScad and then have one ordered, but it will be tricky even for me as it can't be drawn only with ellipse equations. It triggered me when I've seen this guy while I was looking for a way to harvest back EMF: kzbin.info/www/bejne/rKCreKyEbpiFq5Y He proves nothing, but the circuit is interesting. I would like you to pulse DC thru the spinning spiral coil and see if you get voltage spikes at the same time with those high amps.

[@fxeconomist]

I am trying to get my own machine built and I am working as fast as possible but there is something that puzzles me. I figured to use pot ferrite magnets (with the pot) to have them affixed to the shaft but information on them is scarce and producer first4magnets only makes pots with diagonal magnetization, showing both poles, instead of axial. I've seen in Aaron Murakami's video a section of Peter Lindemann research in the 70s (Borderlands thing) where they used a few magnets on a disk showing different poles and got AC sinewave ; but DePalma made the big magnets by assrmbling hexaedric magnets together thus alternating poles and got DC ? I would go for pots, easy peasy, but I don't want AC cause that can't allow the voltage experiment. What am I missing here ?

[@sidster64]

The main take away is opposing magnetic that very important

[@joew5559]

Did you build it with volts yet? Tell us your experience that failed to so we know what is working or did you give up on all of this? Should I made a small kit too since you had the 3-D printed workworked out

[@FaradayResearch]

I had come too a roadblock....so I had put it on ice for a while

[@joew5559]

@@FaradayResearch I don’t know if this was said to you before but I have an idea…. A few guys are working with frequency in electricity is Joel lagace..u tube .. now.. but I’m wondering if it can be added.. ask Joel he is a out of box person.. he will answer you. .. tell him Joe w sent ya.. ✌️

[@TheProfJones]

So Bruce DePalma claimed over unity when he reached 6000 rpm on a Faraday-type spinning disk generator. Whatever happened to him and to his invention? Thanks!

[@FaradayResearch]

Bruce DePalma died in 1996. He died in New Zealand. From what I've heard, his machine is not over unity. According to Eric Dollard, there is only one way that you can make that machine over unity and that's if the magnetic field that was created was pulsed into an AC type field, then that could be extracted accordingly to produce high voltage and high current. Unfortunately, his machine was only able to create high current at mediocre voltage due to the architecture of his design. Unfortunately, his design made the machine extremely big and heavy which is kind of unpractical for a lot of uses. Maybe the industrial use might be more feasible, but as far as output voltages it, his device did not have the architecture to produce that.

[@TheProfJones]

@@FaradayResearch Are you still working on the Faraday-disk project shown in this video? If not, let me be frank, I would be interested in renting (or buying) your build so I could do some tests. (I do not have a 3D printer, for example, but I have a lot of test equipment.) I would add at least one earth ground, for instance. I would also like to try segmenting the conductive surface (as recommended by N. Tesla). I'm getting ready to try my own build, but renting yours would save me a lot of headaches in getting started, if you are willing.

[@FaradayResearch]

I thank you for the interest in the video that I did on Bruce De Palma.... Yeah he passed away in 1997 in New Zealand... He fled the US because of the harassment from the government. Where the invention pretty much did not evolve from there. There's a guy in India named tawari... He also built this machine and got great results. The only problem with the machine is it has to be built at a very large scale in order to get over unity and makes it very unpractical for the average person to build and implement into their home or whatever... As far as I know the machine he built pieces or the whole machine could be sitting in a warehouse. Somewhere in Australia was the last time I heard but it hasn't seen the light of day since his passing

[@FaradayResearch]

I thank you for your interest in my project. Unfortunately that project has been disassembled. It would take some time to get it back up and running again. That's something I would have to work on in the near future, but the device itself is very easy to build. You don't need a 3D printer. All you need is too large fishing magnets, a steel axle and a couple of bearings and DC electric motor. That's very efficient and you can have your own end machine up and running very very quickly​@@TheProfJones

[@jprice1122]

A lot of bearing chatter. Maybe try for a maglev bearing. Mercury contacts instead of brushes would cut down friction losses. This would necessitate containment (not hard for a 3d printer). Wonderful work. 👍

[@jprice1122]

To clarify, I've gotten over 7000 rpm with a 1/4 lb. Rotor ... 12.4V @ .15A

[@wolfforce3740]

@@jprice1122 Nice job! What was the diameter of your rotor? I`m planning to use 4 inch rotor.

[@jprice1122]

@@wolfforce3740 It was an old hot dog roller, 7 or 8 inches long by 1" diameter. Neos in the ends for the maglev and 4 (1/2" x 1/2") neos spaced around the center lengthwise. kzbin.info/www/bejne/iXnGo3iOq5mSorM

[@wolfforce3740]

@@jprice1122 The maglev bearing idea is super cool! ✨

[@thewonn]

What is the input to achieve 20 amp? Very cool.

[@FaradayResearch]

Yup 20amps. Sometimes I get it up to 30 amps

[@INVENTOR3]

Hello! 😎

[@thewonn]

@@INVENTOR3 hey Paul good to see you. Waiting on a new vid from you man:)

[@INVENTOR3]

@@thewonn Good to see you too. I have enough footage to post 2 or 3 videos now, but need time to edit and upload them,,,, soooon :-)

[@willrobertson826]

Would be nice with video

[@subashinixerox5772]

hey from beginning i am a bit confused on how the design is. do you have both magnets and a copper plate in between the magnets? or just magnets alone? if its the first case, do you spin the magnets and the copper plate at same speed (by making them be separated by few millimeters gap between the copper and the magnets).

[@johnthomas5806]

new to this.......could it be used to charge a battery (Tesla PowerPack?)

[@FaradayResearch]

If it can run electric motors... I imagine it could charge that battery pack too

[@scottgarrett2056]

What volts are you getting?

[@FaradayResearch]

.065 volts... very low. High current 25amps

[@jarosawjaskuowski3179]

Amps fine but Voltage?

[@FaradayResearch]

Very low 60 too 100 MV

[@WORLD_OF_M4V3R1CK]

Nice job man! Thanks for sharing. Are these faraday disks inside or just 2 magnets? Thanks again, keep up the great work!

[@FaradayResearch]

Yep, just two magnets

[@CharaTR]

How do we convert current to voltage?

[@FaradayResearch]

Step up transformer

[@CharaTR]

@@FaradayResearch wait, then doesn't this make 10000 or 800 current 10000 or 800 volts?

[@DeryckThompsonChasingtheDream]

what would be the slowest rpm for about 5 amp ? and is your shaft a copper one or steel.? thanks Dave

[@FaradayResearch]

Hi Dave I could get a stable 5amps at about 500 rpm. And the shaft was steel Rod ....I used Dremel brushes for the contact points on the magnet which worked very well Cheers Mike

[@RajarshiGhoshal]

Check out Dr Paramhamsa Tiwari's work. He replicated Bruce Depalma

[@subashinixerox5772]

actually Dr. Tiwari's machine is not like Dr. Palma's, because Former used just magnetic spinning as load attached to shaft , which is connected to a regularly used high HP AC motor (that is used for water pumping) for getting higher electrical power as output from lower electrical input power. this is commonly a large size machine of the over unity (motor - coil as stator with spinning magnets) model shown on youtube.

[@RajarshiGhoshal]

@@subashinixerox5772 Very vague and unclear what you just said. Both Palma and Tiwari have redirected the back emf to be used as an additive rather than resistive to get over-unity. Dr Tiwari has himself said this on multiple occasions that his system is inspired from Palmas work.

[@m.o.r.p.h.e.u.s]

Btw what's the best Over Unity Generator u have worked on or would be making in the future ?

[@FaradayResearch]

Well for starters probably the best I've worked on it would be the jewel thief circuit... the pulse motor and I'm working on the Don Smith method of generating power and now I'm working on a new flywheel type design which is going to be a flywheel and a pulse motor kind of combined into one unit so it's kind of the best of all the technologies put into one system so I'm working on that now it'll probably take me at least a year to complete it working on the flywheel design as we speak so little by little I'll be showing the stuff on my channel but I'm up to thanks for your comments Mike

[@m.o.r.p.h.e.u.s]

@@FaradayResearch Thanks so much for the work and the uploads for people to get knowledge , I highly appreciate it ❤️

[@friendofwise4295]

Wonderful work ! What is the Input Power and Output Power ?

[@FaradayResearch]

60 microvolts.... at 25 amps

[@friendofwise4295]

@@FaradayResearch Thank you Sir for your prompt reply. What do you get for INPUT POWER and OUTPUT POWER so that we know the GAIN, hopefully it is OVER UNITY !! Thanks again. p/s: FYI, I'm from BC Canada, now visiting family in Taiwan.

[@FaradayResearch]

@@friendofwise4295 The input power is the power used to spin the magnets at high speed. So you can really try to find a efficient motor to spin the magnets as quick as possible. Bruce de Palma says that the magnets should be spinning at 6,000 RPMs to get over unity but the size of the magnets are also a very large factor and how much power output you can achieve with this device. I put this project on hold for a while. I had more research and to do on this device and I'm revisiting this device now which I'm doing in behind the scenes for obvious reasons because the device has properties that can happen to the device while it's running which a lot of people do not know about???(secret) and this is what I'm trying to prove now..... I will not be disclosing any more information on this device.... because the implications are very serious.... If you do some serious research on the device, you'll find out when I'm talking about but I will Not reveal it on KZbin ever!

[@friendofwise4295]

Well noted. Thanks

[@bobjary9382]

​@@FaradayResearch The motor spinning the shaft is 12v dc ? If thats correct what current is it drawing to spin the shaft fast enough to get 20A. Thanks

[@sidster64]

It's a Great Video I have a system to create volt's and is additive be design . I wish we could talk I would like some pointer. Thanks But i will keep trying Thanks for a great video

[@FaradayResearch]

Sure sounds good just send the emails to [e-mail]

[@mcorrade]

So what was the name of this original motor design you made? You mentioned it in a previous vid but removed it

[@FaradayResearch]

Hey the original name was the N machine

[@mcorrade]

@@FaradayResearch cool but you called my another name. A persons name I think?

[@FaradayResearch]

The Faraday disk. Or Tesla disk

[@mcorrade]

@@FaradayResearch Also do you have a build video on this device? Would love to emulate

[@FaradayResearch]

@@mcorrade yeah I have not done a building video for this generator yet... maybe I will do it soon

[@operarioespeculador-trader1776]

Hi. How much input in the motor do get 20 A? And what voltage togeter with current output? Congratulations.

[@FaradayResearch]

About 8 watts to drive the motor

[@timothyadams7599]

I seen the D.C. power supply. So I’m confused are you using D.C. voltage and as you increase it you produce more amps?

[@FaradayResearch]

The DC power supply is used to spin the magnets.... it's not adding power to it all the amperage is coming from the magnet spinning ....it produces very little voltage about 40 millivolts but high amperage.... the DC power supply just runs the motor that turns the magnets

[@ElectricEdgeAi]

Just curious... does it make a difference how far apart the magnets are from each other? I.e. does closer together give you more amps?

[@FaradayResearch]

The distance of the magnets apart have nothing to do with it it is the rotation of the magnets that creates the amperage my magnets are about 3/4 of an inch to 1 inch apart but has no relevance to the production of amperage it all has to do with rotational velocity

[@ElectricEdgeAi]

@@FaradayResearch Cool. Very interesting stuff, thanks for sharing!

[@rollmeister]

At such a low voltage, the resistance in the meter, wires and bushes will drop the amps massively.

[@YaseenExperience]

❤❤❤❤❤👍👍👍👍👍🔔

[@stevenphillip1159]

Where can I buy that housing you have

[@FaradayResearch]

The housing that I used is custom made by myself took about 2 months to design and then I printed it on my 3D printer. It's my completely my own design..... At this time I haven't considered releasing the designs maybe that's something I might look into in the future if I get a website going on for my old unity stuff

[@Gacha.Cupcake]

I am a noob but tesla coil puts out a lot of volts with little amps. What I you feed this intonation tesla coil? I am just shooting from the hip At my age of 75, my brain does not produce neither amps nor volts.😀🤩😂🤣 BTW, if you share the 3d design, I can print it up and experiment with it to see if any we can get anything out of this hard work you have done.. I realy want to build an overunuty something before I die. God bless you brother. Keep up the good work and please share.

[@FaradayResearch]

Please watch all of Don Smith videos... he explains how the diameter of the coil and the direction CCW and clock wise will effect the amps. As well alot of amps ( current) are drawn from the capacitors in the circuit.... I hope this helps. .... cheers!

[@bobfuqua384]

Try grounding it with a earth ground ?

[@FaradayResearch]

Yeah there is many things I need to test... that's one of them.... apparently this machine can alter time.!! That sounds crazy but I will try it

[@ezzatziadeh720]

You can rise the voltage by Aaron Murakami way !!!, So easy.

[@FaradayResearch]

Send me the link

[@ezzatziadeh720]

I send it for you but some one deleting the link!!

[@FaradayResearch]

@@ezzatziadeh720 that is weird I didn't delete it I never got a link from you????

[@ezzatziadeh720]

@@FaradayResearch I sent it 3times here, any way, use a step up transformer on the output section

[@fransinatra4474]

Patrick Kelly , refiere al uso de un disco de cobre , con imanes adheridos a el , con polaridades alternadas , tomando corriente de cepillos dispuestos a 90 °, en la periferia del disco , obteniendo corriente corriente alterna , aplicable a un transformador , elevador de voltaje. kzbin.info/www/bejne/mYKYhpilqtCSjLs Un abrazo.

[@Nordic_Mechanic]

amp with no load though

[@FaradayResearch]

Correct

[@69Atho]

When your 5 amp clip leads don't smoke up with 20 amps going through them lol.

[@FaradayResearch]

Very low voltage