#NanoLongRange

Build of the Dave_C Nano Long Range quad.
VTX amzn.to/3qVg32I
FC amzn.to/3lo5KD6
Dc-to-Dc converter www.pololu.com/product/2562
LC Filter amzn.to/3vvb4cm
Camera amzn.to/3lr2DKq
Battery analyzer amzn.to/2P4v2tE
Frame stl www.thingiverse.com/thing:476...
If you really want to support me, head over to my web page www.tweetfpv.com to see all the ways you can support me and my work in the FPV community.
Patreon page: / tweetfpv
BetaFPV: betafpv.com?sca_ref=360201.IdW7j0Cv8A
Insta360 Go: www.insta360.com/sal/go?insrc...
GetFPV referral link: www.getfpv.com/r/97054/
If you would like a set of your own radio grips please visit my Etsy store: www.etsy.com/shop/TweetFPV
Help support me by clicking through this link the next time you purchase from banggood. www.banggood.com/custlink/Kmm...
If you need one-on-one troubleshooting for your equipment, come over to Discord and I can help you out: / discord
Buy me a beer or two: paypal.me/TweetFPV
Like me on Facebook / tweetfpv
Follow me on Instagram / tweetfpv
Email me at [e-mail]
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Tools:
Wera Kraftform Plus 354 Hex-Plus 2.5mm Hexagon Professional Screwdriver: amzn.to/2Wd6K1z
Wera Kraftform Plus 354 Hex-Plus 2mm Hexagon Professional Screwdriver: amzn.to/38MN0Xz
Wera Screwdriver Hex-Plus, 1.5 mm x 60 mm: amzn.to/2Cu9LDn
Pocket Multimeter: amzn.to/3elmd5Q
RDQ prop Tool: www.racedayquads.com/products...
TS80: amzn.to/3gPsnwz
X-acto knife: amzn.to/2OhG3Ep
Soldering tweezers: amzn.to/326ujNe
Filming:
Sony A5100: amzn.to/38Pme0L
Comica boomxd wireless mic: amzn.to/3gQB1uV
Joby Gorilla pod: amzn.to/3eiz0pt
Ethix SD card holder: newbeedrone.com/products/ethi...
Microsoft PL2 ARC Touch Mouse: shorturl.at/bm137
Quads and quad parts:
APEX HD frame: www.getfpv.com/impulserc-apex...
Ethix S3 Props: www.getfpv.com/ethix-s3-water...
Five33 Tinytrainer: flyfive33.com/product/tinytra...
DJI FPV system: www.banggood.com/custlink/GGG...
Eachine FPV Watch monitor: www.banggood.com/custlink/mK3...
HOTA D6 Pro: www.banggood.com/custlink/DGK...
Betafpv 65x HD: amzn.to/2ZZSDOf
happymodel mobula6 25,000KV: www.banggood.com/custlink/D3m...
TBS Tango2 Pro: www.getfpv.com/tbs-tango-2-pr...
Betafpv BT23.0 charger: amzn.to/3iPKEvP
Strix PH2.0 charger: amzn.to/2BSxvl1
Lumenier Axii Long Range antenna: amzn.to/38V6t8E
Ethix Liop bag: www.getfpv.com/ethix-heated-d...
DJI PFV goggle analog adapter face plate: www.ebay.com/itm/Faceplate-fo...
ISDT BG-8S lipo checker: www.banggood.com/custlink/vGK...
Earth bound entertainment:
ODROID-GO Advance Black Edition Aura Black: www.hardkernel.com/shop/odroi...
RK2020: rkconsole.com/products/rk2020...
3D desings:
3D printed zip tie design: www.thingiverse.com/thing:148...
Hota D6 screen cover: www.thingiverse.com/thing:377...
These videos take a lot of time shooting and editing. If you like my content, please like and subscribe. Leave a comment if you have any questions. Thanks for watchin'!
Thank you and keep flying!
Note: The links above are affiliate links. By clicking one of them before you purchase anything on Amazon, or banggood you're helping support me making videos for this channel.
TOC:
intro 00:00
Parts 02:50
Wiring 08:13
Main power 08:50
Motors 10:00
VTX 12:00
Camera 13:00
DC-to-DC LC filter 14:30
RX 17:30
Completed build 18:00
Betaflight 19:25
Flight 23:38
post-flight 30:00
Final thoughts 32:00

[@eliasmorley757]

I really enjoyed and appreciated the video as I frequently referenced it as I did my build. I would suggest adding a description on setting up the soft serial port. Thanks for the vid!

[@UKkenny]

Brilliant video - yes indeed , covered ALL topics from start to finish ! loved it

[@chrismel9000]

Very cool, thanks for doing a build video.

[@KLNYC]

that condense mic sound soo good. i wish my back yard are like that.🤘

[@inspirefpv7213]

"Long range is not heart racing or exhilarating as racing"... My heart definitely starts pumping when the wind direction changes 2km out and I now I might not have enough power to fight it back home 😉🤣 Great Video! Excited to see where these sub 250 1s nano longish-range builds take us in the future!!

[@TweetFPV]

You and me both!

[@thejeffhendrix]

or when you are out a km and your video goes out

[@SchroediFPV]

Really good, mine is in the works 👍

[@nerdCopter]

+1👍 nice!! 💪 heck yeah 16mins of "explore" (8 mins out 8 mins in 💪) now double 18650 version if the weight is still bearable. There's a remix as well that has a built-in battery clip

[@chuansheng]

Awesome and detailed build👍 you shld include yr parts used in yr description too especially the motors and vtx specs😁

[@leifericson2061]

Verry nice build man and verry verry nice place to fly on😁🤪

[@HomeDronen]

Awesome build Tweet...I need to purchase me a printer 😎👍Amazing 15+ minute flight.

[@TweetFPV]

3d printing is a complete time suck!! but i highly recommend it!

[@chancewilson1161]

I like it

[@pjoterurbx]

Super !

[@TweetFPV]

dooper!

[@johnk8825]

Very nicely done Dan, thanks for taking us along for the build.

[@TweetFPV]

Any time!

[@stevemann6082]

petG is not far off from polycarbon ( about 15 20% beneath polycarb if i remember right). i am thinking if you just go twin battery cell you cure the low voltage 2.5v vtx cut out and you wont need the step up buck. just a thought. i love this class of quad. thanks for showing us your take.

[@TweetFPV]

If I went 2s then that kinda takes away from the uniqueness of this quad.

[@MichaelDFPV]

Awesome video. I am preparing to start my build of the Fractal Wingman. Now that I have all of the parts I just need to find the time to build it.

[@TweetFPV]

Oof time.... Where do I buy some of that..

[@MichaelDFPV]

@@TweetFPV Not sure but if I happen to find some I will let you know. 😉

[@TweetFPV]

Please and ffs if you have an aff link for it let me know!

[@MichaelDFPV]

@@TweetFPV 😆🤣

[@BrandonBeans]

Don't forget to get lots of grass and dirt on that exposed servo tape or it won't work as well! I swear it helps cure the adhesive quicklier ;)

[@TweetFPV]

😂

[@parshvapatel8484]

TweetFPV I am completely noob how to start something long range in small budget

[@TweetFPV]

I probably won't be going into any more detail on this particular build. You can get a rekon 3 for less than what I have into this build. As far as radio and receiver there are many different types out there and they all work a little differently.

[@FOCKHOUSE]

I got my orqas back from customer service a few weeks back, and without them even saying anything, I noticed they either tweeked or upgraded the fans.

[@TweetFPV]

Nice! They certainly needed to be updated.

[@andytaylor3321]

i just builtmy first LR lol it has the flywoo 4in frame brother hobby 2004 3150kv motors...lol

[@GR8SCOTT]

15:45 is pretty good! VTC6 would have been better.

[@MarksRandomVideos]

Nice - you are way ahead of me am just about to solder mines up this weekend. Question - if we run it on 2S Lipo (I dont have the 18650 holder) will the DC-DC converter blow up at 8v?

[@TweetFPV]

It depends on which converter you have. Check out the spec sheet and make sure it can handle 8.4v input.

[@valden]

May pick one of these up once someone offers the frame as a full kit with battery clip. Lol 👍

[@TweetFPV]

That would be cool

[@haschkatze8372]

He does now

[@TweetFPV]

I saw that! Looks awesome.

[@valden]

@@haschkatze8372 lol sweeeet

[@haschkatze8372]

Yeah I calculated it how much it would cost me if I DIY it, but its CHEAPER to buy it from him

[@BotanicalOdyssey]

Are there any frames out there that you could buy that would substitute well for the 3D printed frame?

[@raffyturc]

nice! 45deg cam angle could be way too much for a 1S li-ion discharge rate.

[@thejdolby]

Great build video and perfect timing! My last part should be here in two days and I'll be building this also. Question... On your Betaflight Ports tab, I see USB VCP and UART1 are both set for "Configuration". Why is this? I was hoping there would be two hardware UARTs available. I wanted to see if I could add a GPS, so my plan was to use UART2 for the TX/RX on the GPS and UART1 (TX only) for my ImmersionRC Ghost receiver. I can use the Ghost receiver to directly control the VTX via Tramp. Now looking at the config you have, I'm not sure this will work. do you have any advice?

[@TweetFPV]

The reason why there is MSP and uart 1 are selected as "configuration" is because there is built in WIFI for using the speedy bee app. So you will only have 1 hardware UART available on this board. i do not think that this FC is going to work in the way you would want it to work for your intended setup.

[@thejdolby]

@@TweetFPV Hey thanks for the quick reply! I thought it might have something to do with the WiFi. Makes sense. Oh well, the GPS was just going to be a nice to have to actually see how far I could fly it out and back. I can still make it work without it. Thanks again!

[@madeintexas3d442]

Awesome video very helpful. I am thinking about building this. Does anyone know if there is a similar 3d printed drone that supports long range fpv along with a gimbaled camera?

[@AndrewMurphy8383]

would i need the lc filter and the step up converter if i dont plan to run fpv?

[@Rocketyfox]

Petg is lighter and more impact resistant, but can be too flexible for some frames. Pla is slightly heavier, but is a bit stronger and significantly stiffer. Ive had good results printing whoop frames and planes frome both.

[@TweetFPV]

Pla will warp and fail on the Quad expecially where the Vtx and fc are mounted. It just gets way too hot.

[@harpalyke4659]

@@TweetFPV ABS might offer a good compromise between both. I think DaveC has a carbon fiber version of his design in the works though.

[@AerialWaviator]

Very informative build video. Great work on follow-on carbon fibre frame as well. Without going done the what-if rabbit-hole of doing part mods (to this build); wondering what your thoughts are on a 2S-18650 powered build? Seems 2S would eliminate the low voltage VTX/video power issues, but add another 45-50g (18650 weight). Know the Rekon-4 and Flywoo Explorer, both 4" will fly on 3S and 4S, but that's better fitted to using a pack vs single cells. Really like the idea of a 2S-18650, so hoping someone has figured out a good motor+prop configuration?

[@TweetFPV]

2s voltage would certainly make this a better platform but the weight of 2 18650s might be too much.

[@AerialWaviator]

@@TweetFPV Thanks for quick reply. Understand, too much weight for this motor+prop combo. I might just need to experiment.

[@morssha]

Why is this called LR? Wouldn’t it be better called endurance? Great build! Amazing to fly that long.

[@TweetFPV]

Yea that would be a more appropriate name for this quad for sure.

[@majorlee9714]

Might be a good idea to add a diode on one of the power leads, in case the battery is inserted incorrectly.

[@TweetFPV]

Yea that's a good idea. But I trust myself.

[@raccoonbadger851]

What parameters of this diode you suggest? Cheers

[@AltMarc]

You would need a "low voltage drop diode mosfet" circuit or else you loose flight time.

[@3000gtwelder]

You should make one with 2 cells, that has a better antenna

[@SilverbackSasquatch19xx]

I’m team pla I have tried other filaments but I get the best luck with pla

[@junsport]

Any other recommendations on a 18650 charger/analyzer? The one you linked it sold out and I don't really want to buy from China.

[@TweetFPV]

the Opus BT-3100 is another good choice amzn.to/3aAOLsV

[@lucbisschops]

Nice video, 👍👍 i printed it in PetG 20% infill, my only problem is, the cam mount inlay is so thin, it breaks easily, and the bottom cover is really thin as well, how many walls did you use to print? Mine is set at 2 outer walls. Really nice build👍

[@peterarbeitsloser1746]

Always use 3-4 walls for strenght and more then 20% gyroid infill. (My opnonion)

[@maxbeem196]

Very good video and instructions! Can you confirm the temperature problem as described in the comments from thingiverse? What is your core temperature? I have over 70 ° C when idling ... FC Zeus 5, VTX Zeus, filter and stepper

[@TweetFPV]

I wouldn't pay too much attention to the core temp. It comes on way to early and just scares people.

[@Michael-qy8yx]

I always get massiv overeating problems 110+ degree celcius. Not flyable -> temp drift and probably short flying time due to high temp. I use the same hglrc zeus board like dave c. Bevor i tried the happymodel f4 elrs controller with the same problem. Does anyone know a solution or a working component? (* i use Flywoo 1202.5 11500kV motors )

[@boomboomtradingroom9646]

Might be a dumb question - but something like the 5V step up converter.... would we be able to run something like that on a shark byte whoop board w/ 18650? the board takes in 2s and I love how it's not too heavy

[@TweetFPV]

Anything extra to this bill will really effect it. It's kinof on the edge of that one 18650 can provide.

[@TweetFPV]

But yes anything is possible

[@lukasmunster8908]

Hi Dan, great build video! Question: Do you think this setup would work with HD split camera (e.g. Runcam Hybrid 2)? I've remixed DaveC original design so now the HD cam should fit, however, there is approx. 15-20g increase in AUW (new frame, HD cam, immortal T, foxeer mini lollipop..). Do you think this setup could deliver at least 10min flight time?

[@TweetFPV]

It will fly, probably not well. The Quad as is is already kinda heavy for the power train. You might get 10 minutes but It will be a stretch for 2 reasons. More weight and those HD board draw a lot of power.

[@lukasmunster8908]

@@TweetFPV thanks for fast response, I have some spare caddx eos2, maybe I'll end up switching to original design and less power hungry and lighter setup.. since the hybrid 2 is on its way and I spend quite a time to remix the original design, I'll give it a shot :) if it turns to fly bad, I'll keep the HD cam for more powerful build

[@TweetFPV]

Yea that's kind of how I approached this one. I could always reclaim the parts for a different build.

[@3000gtwelder]

What is the weight on one of those things? Oh, by the way, I'm loving those grips you made me for my radios, they work awesome! I kinda hated my Tango for awhile until I put those on it, they made all the difference!

[@TweetFPV]

Awesome, I'm glad you like them. This little Quad is 110g auw

[@3000gtwelder]

@@TweetFPV Wow! That's pretty cool.

[@Siamect]

Be careful if you print in PLA... I did that 5 years ago and it was a 5 inch. I left it in the car and it was very hot. The PLA got soft and the drone became a banana....

[@davidmora4485]

Que modelo de motores son esos y qué potencia tienen

[@MsDidits]

Estimated total cost how much dollars,Sir ?

[@Duke-Pro]

Thank you! Nice build. I allready odered the parts, but with some changes. What do you think about Happymodel DiamondF4 AIO F411 controller? Will it fit better than zeus? And I took RunCam Nano 2. Will it be OK, if I wire it to the same powerline as VTX?

[@TweetFPV]

There are no issues with fitment of the Zeus. so the diamond FC should be just fine since the footprint is the same but smaller than a normal AIO. But you will most likely need to mount the board 90 deg of center or upside down to allow access to the USB port. The camera will be fine for your setup, however the FC you have specked is only good down to 2.9v . You will be leaving a bit of flight time on the table since these LION cells are good down to 2.5v (depending on the cell).

[@Duke-Pro]

@@TweetFPV Thank you! So... Obviously,I made a mistake, by choosing diamond =( But, what if all electronics are powered from bec? Will it die?

[@TweetFPV]

No that would work fine, although you won't know what your cell voltage was since the bec would always provide the fc with 5v.

[@Duke-Pro]

@@TweetFPV I think, the solution might be a camera with built in batt sensor, like Foxeer Micro Cat 2. But It's too heavy, maybe there are something in nano size with the osd and voltage sensor (with fourth wire for it, like in cat2)?

[@TweetFPV]

Yea that's what I was thinking. Although I haven't found a micro camera with built in voltage sensor.

[@fpvraiz]

Qual motor tio ? Quel kv? Por favor

[@maciejklasa6783]

Thank you for this video, this was very informative. I was hoping to learn how to wire the engines though: there a re 2 wires and I have no idea in what order to solder them. Can you recommend any resources to learn more? This is my first quad but I have experience with electronics and soldering, I'm just new to quadcopters and fpv.

[@TweetFPV]

There should be 3 wires coming from each motor and the order doesn't matter what order they are soldered to the esc.

[@maciejklasa6783]

@@TweetFPV Thank you. That makes sense, they would be colour coded otherwise.

[@TweetFPV]

Do your motors have 2 or 3 wires?

[@maciejklasa6783]

@@TweetFPV Three wires. I'm getting HGLRC AEOLUS 1202.5 11600KV.

[@Oxizee]

Try an 26650 next time with 5500mah :D

[@joesvenskason6471]

Does anyone build it with the alternative Recommendation from dave_c ( the jhemcu board ) is there any wiering plan online , I think I screwed up 🥴 sorry it’s my second build , ( wiring / soldering training for me ) I thought I watched enuff bardwell videos I am ready for this 🤣 what can go wrong ? There where no Zeus boards left here in Europe 😄

[@TweetFPV]

There is always a wiring diagram. I typically just Google the name and model of the board and pinout. So like "jhemcu f405aio pinout" and you should find something. Also check the manufacturers product page. Sometimes they have them there. Good luck!

[@hurricanezaza]

Can I use a resin printer for the frame?

[@TweetFPV]

No, it would be far to brittle.

[@CricketyChris]

Try turning crsf telemetry off through your radio for better video! Can still get it through the osd

[@TweetFPV]

That's a good idea. I'm only on 25mw for these flights. I fly everything at my place on 25 just to see how each Quad stacks up against others. This one was certainly worse than others.

[@CricketyChris]

@@TweetFPV it definitely looked similar to my 1s with crsf before I turned tel off. *fingers crossed for you*😎

[@TweetFPV]

Yea I remember having the same issues with poorly placed 900mhz antennas before.

[@Dia1Up]

I'm pretty new to FPV, my last drone I build back in like 2011, with one of the very first commercial FCs. Can someone explain all of the things on the OSD? Voltage and time is obvious, but what about the rest? (Just ordered a Rekon 3, after I found out it's an actual partnership with dave_c)

[@TweetFPV]

I could certainly explain what's on your osd but I don't know what's on your osd. Do you have dvr? You can post a pic on my discord server in I'll be happy to tell you what each thing means. Www.tweetfpv.com

[@Dia1Up]

@@TweetFPV will do! Currently in the mail. I'd imagine it's customizable

[@TweetFPV]

Yes it certainly is in the betaflight configurator.

[@DVN_FPV]

Hello, what clue you used to hold the batterieholder in place?

[@TweetFPV]

E6000 amzn.to/3MgjUmL

[@DVN_FPV]

@@TweetFPV Thank you sir

[@badraven9532]

I'm frozen on my build as I'm awaiting motor supply. I printed the frame in PLA, PETG and ABS as a test. PLA was the most rigid, ABS the most flexible, IMO too flexible. I'm using cured PLA.

[@TweetFPV]

The electronics get too hot for pla and will warp the frame.

[@badraven9532]

@@TweetFPV Then your experience is very different to mine, as I have a number of PLA printed frames in use, from ones where the brushless motor location is somewhat tunelled to keep dirt out of the motors bottom area (my garden basher!) and the electronics are quite heavily enclosed with no straight line path in order to keep dew droplets away, through to 6, 7, and 8mm brushed that rely on the motor casing friction in the frame to hold them in place. Not once have I had warping/undue expansion/melting. Thats with plain ordinary PLA, cheap stuff from HKing. I have even made curved thin hollow wing tips to convert an EFX Extra to the larger span EFX Racer (in black!) and left the thing in the sun, no movement at all.

[@martinmacko7297]

Hi! I did test on desk bench with poloiu booster and it could not sustain 600mAh already at 3.6V input. Did it work ok for you?

[@TweetFPV]

I'm not sure what you are asking? are you saying that the dc-to-dc converter you have would not keep up with a 600mAh load at 3.6v or below?

[@martinmacko7297]

@@TweetFPV Hi. Yes. I used exactly same dc-dc as you and once batt was around 3V it started to shut down video/receiver which is powered from this small green dc-dc booster.

[@TweetFPV]

Bummer, you must have received the wrong part or received a defective on. Mine works right down to 2.5v as advertised.

[@martinmacko7297]

@@TweetFPV interesting...thanks!

[@iulseyer]

the FC specs is 3s - 6S, yet still flying below 1s (2.8 atleast)?

[@TweetFPV]

You are looking at the wrong Zeus fc. There is a aio whoop board and there's a 20x2p Zeus. This is the one one I used.www.hglrc.com/products/hglrc-zeus5-aio-1-2s-f411-flight-controller-5a-bl_s-4in1-esc

[@iulseyer]

@@TweetFPV oh yeah..I'm looking for the bigger version.. by the way, nice video... thanks

[@elielmarcosromancini3545]

Betaflight dump, please

[@borismonreal3998]

Would brushed motor also works?

[@TweetFPV]

Not in this frame or with this flight controller

[@mhnproduction]

Is it possible to put a Insta Go 2 on this 🤔

[@TweetFPV]

Absolutely!

[@Maceyee1]

why wouldn't i use the step up on the whole board?

[@TweetFPV]

A few reasons. Biggest one is you'll lose the cell voltage reading. Your osd would always show 5v till it dies. And the reg cant provide enough amps to support the entire setup.

[@johnholland3476]

Wonder if dsmx satelite reciever would work on this

[@no-trick-pony]

Completely unrelated: Where do you find a house like that? Is that common in the US? I LOVE that house. No neighbors, just forest around. How much do you pay for something like that in the US?

[@TweetFPV]

It's not uncommon. You will need to live away from the city/urban areas. Also it depends a LOT in which area of the county you live. A house like this can be found for $100,000 to a mill depending on location. Where I'm at about $300,000. If you are curious how housing prices look in the us go to zillo.

[@no-trick-pony]

@@TweetFPV Thanks a lot! :)

[@bobbenkhe8306]

what is the flying weight?

[@TweetFPV]

106g

[@skvaderfpv]

Would the iflight succex f4 1s board work in this build?

[@TweetFPV]

Yes it should. I was on the fence about using that FC but it comes with a VTX. With that it could be difficult to use a different VTX if you wanted to in the future that's the primary reason why i did not go with the iFlight AIO.

[@skvaderfpv]

@@TweetFPV the VTX is pinned and has solderpads on the bottom of the FC. I think that if I manage to find out which one is ground, I can remove the VTX and solder on a unify nano. I think I will try to use a 3 inch Armattan tadpole frame for a first prototype. Might be a little heavy.

[@TweetFPV]

Ok. Then that was about all my reservations about the iflight board. Also it should be noted that the Zeus has wifi so you can use the speedy bee app to work bf.... If that matters to you.

[@skvaderfpv]

@@TweetFPV wifi, that is nice. Also explains the price difference. I might order one of both just to try. Thanks

[@TweetFPV]

Well if you do.... Shamless plug coming, head over to www.tweetfpv.com and click though one of the affiliate links . 🤮 That hurt my soul. 😂

[@kamaleao39]

Where i can find the motors please?

[@TweetFPV]

Fpvcycle.com

[@hupo]

I updated this board and now soft serial doesn't show in ports. Even with it selected under config. The fuck

[@hupo]

can you do me a solid and backup your board and send it to me?

[@TweetFPV]

Soft serial doesn't show in the ports tab until you resource assign something to them.

[@TweetFPV]

# # diff all # version # Betaflight / STM32F411 (S411) 4.2.8 Feb 15 2021 / 12:09:04 (101738d8e) MSP API: 1.43 # config: manufacturer_id: HGLR, board_name: HGLRCF411, version: 18c5b9b5, date: 2020-05-25T12:32:42Z # start the command batch batch start # reset configuration to default settings defaults nosave board_name HGLRCF411 manufacturer_id HGLR mcu_id 003d00173030510531333433 signature # name: nano LR # resources resource MOTOR 1 B06 resource MOTOR 2 B07 resource MOTOR 3 B04 resource MOTOR 4 B05 resource MOTOR 5 NONE resource SERIAL_TX 11 B03 resource PINIO 1 B10 # feature feature -RX_PARALLEL_PWM feature RX_SERIAL feature SOFTSERIAL feature TELEMETRY # beacon beacon RX_LOST beacon RX_SET # map map TAER1234 # serial serial 0 1 115200 57600 0 115200 serial 1 64 115200 57600 0 115200 serial 30 8192 115200 57600 0 115200 # aux aux 0 0 0 1300 2100 0 0 aux 1 1 2 1700 2100 0 0 aux 2 13 1 1700 2100 0 0 aux 3 35 3 1700 2100 0 0 # vtxtable vtxtable bands 6 vtxtable channels 8 vtxtable band 1 BOSCAM_A A CUSTOM 5865 5845 5825 5805 5785 5765 5745 5725 vtxtable band 2 BOSCAM_B B CUSTOM 5733 5752 5771 5790 5809 5828 5847 5866 vtxtable band 3 BOSCAM_E E CUSTOM 5705 5685 5665 0 5885 5905 0 0 vtxtable band 4 FATSHARK F CUSTOM 5740 5760 5780 5800 5820 5840 5860 5880 vtxtable band 5 RACEBAND R CUSTOM 5658 5695 5732 5769 5806 5843 5880 5917 vtxtable band 6 IMD6 I CUSTOM 5732 5765 5828 5840 5866 5740 0 0 vtxtable powerlevels 4 vtxtable powervalues 25 100 200 400 vtxtable powerlabels 25 100 200 350 # master set acc_calibration = -30,25,-92,1 set mag_hardware = NONE set baro_hardware = NONE set serialrx_provider = CRSF set blackbox_device = NONE set motor_pwm_protocol = DSHOT600 set bat_capacity = 3000 set vbat_min_cell_voltage = 290 set vbat_warning_cell_voltage = 300 set yaw_motors_reversed = ON set small_angle = 180 set pid_process_denom = 4 set osd_warn_core_temp = OFF set osd_vbat_pos = 2402 set osd_rssi_pos = 2081 set osd_tim_1_pos = 2454 set osd_throttle_pos = 2424 set osd_vtx_channel_pos = 2101 set osd_current_pos = 397 set osd_craft_name_pos = 2434 set vtx_band = 5 set vtx_channel = 8 set vtx_power = 1 set vtx_freq = 5917 set vcd_video_system = NTSC set pinio_config = 129,1,1,1 set pinio_box = 0,255,255,255 set gyro_1_sensor_align = CW0FLIP set gyro_1_align_pitch = 1800 set name = nano LR profile 0 # profile 0 set p_pitch = 100 set i_pitch = 50 set d_pitch = 70 set f_pitch = 125 set p_roll = 90 set i_roll = 45 set d_roll = 65 set f_roll = 125 set p_yaw = 65 set i_yaw = 20 set f_yaw = 125 profile 1 profile 2 # restore original profile selection profile 0 rateprofile 0 rateprofile 1 rateprofile 2 rateprofile 3 rateprofile 4 rateprofile 5 # restore original rateprofile selection rateprofile 0 # save configuration save #

[@hupo]

@@TweetFPV thanks but I burnt the board because there is literally zero documentation about bridging the pads for sbus. Now my rear two escs are not working and smoking. Fuck hglrc

[@RUMBLE.com_ClickthruMAN]

how much it cost? and why the footage like it's made in 80s? how about digital vtx ones?

[@TweetFPV]

I've got about 200 into this one. As far as the video goes that's analog it can be better if I boost the output power but the low rez image is just how analog is. Digital will not work in this. Too bug too heavy and waaay to power hungry.

[@RUMBLE.com_ClickthruMAN]

@@TweetFPV just bought mjx 5w from reckless guy he lost the camera I'm new on the vtx thing tbh, could you tell me the best affordable 500mtr+ fpv set that able to work with rotg devices, before i saw guy on yt make his own vtx but it need old tv set to receive image SMH if you don't mind of course LOL

[@TweetFPV]

I can better help you on discord. Https://www.tweetfpv.com you can find the link on my website

[@RUMBLE.com_ClickthruMAN]

@@TweetFPV i couldn't afford that for now sounds so expensive anyways I've pathtalk

[@TweetFPV]

Discord is free

[@TheRoadtoGonzo]

I'd like to see one run a HD setup for the DJI goggles maybe go to 2s to see if that would cut it?

[@scottmclaughlin1410]

I was looking at it, the vista nano is 26.5 grams so it would probably need at least that to maintain the range and endurance. But that's just me making a W A G

[@TweetFPV]

This is a better dc to dc converter than the one i used www.pololu.com/product/2562

[@MrAnatolyvizitiu]

Print it out of HIPS, you will reduce the weight by half and make it stronger too.,

[@TweetFPV]

Isn't hips a dissolveable material?

[@AndrewMurphy8383]

petg might be good from i see

[@BHARGAV_GAJJAR]

Just fyi respectfully a honey bee can fly for up to six miles, and as fast as 15 miles per hour

[@leifericson2061]

Verry low battery and this flight is the longest flight i ever seen so far whith nano 1S😁😁😁

[@infinitescales4013]

No need of Esc ??

[@TweetFPV]

This an aio all in one. It has a fc and esc on the same board.

[@infinitescales4013]

@@TweetFPV i though that was a power thing ,like if you go with bigger motors or brushed motor instead of the brushless ?the aio must have some very tight power limits without (external bigger esc's) im studying electronics and i am trying to see what are the limits of the components so im not putting extra weight for nothing on board or use parts prematurely because of the extras watts i might want to add.

[@infinitescales4013]

thanks for the reply in fact :)

[@infinitescales4013]

im trying to figure out the limiting factors. power of the motors or transmitter range ect

[@TweetFPV]

Limiting factor is going to be Vtx transmission power.

[@oleg146]

kzbin.info/www/bejne/eImcgpuApL95mKM damit how u gonna update esc's with such fc mounting

[@slimx4u]

Hello Dan, excellent and instructive video. I was considering the BETAFPV FA AIO flight controller that includes the VTX and a FfSky receiver (www.amazon.com/gp/product/B08N43LS1V?ref=em_1p_4_im&ref_=pe_27562270_580566280#customerReviews). Would this work for this build? Please, let me know and thanks in advance for your attention.

[@quinton3997]

The 18650 suck

[@TweetFPV]

How so?

[@aeQuator]

this is not good. 15 minutes and almost killed the liion. this will fly 10 times and then the liion will be no good. you can fly for up to 10 minutes if not more with a lipo and even have more punsh power due to discharge rate.