NASCAR C10 Chassis Swap, BODY MOUNT!

What else would you do with a wrecked NASCAR truck other than re-body it with a mid 60s Chevrolet C10 truck body?! This project has been in the planning phase for a few years and we finally decided to dive into what we believe is the first 64-66 C10 repurposed as the skin for an early 90s NASCAR style RACETRUCK. This truck being equipped with a 350 CI small block, Jericho 4 speed, quick change rear end, wide 5 hubs, and Hoosier slicks. It should be a terror on the race track and a riot on the street. In this episode, we fit the front fenders, hood, cab, and bed. Multiple modifications were made and the ride height is set.

[@Gniles69]

this is the coolest project on youtube, i need this!

[@BestDamnShopAround]

Thank you! We need to finish it!

[@weekendwarriorpowersports]

I watched the cab video and wanted more!!! This thing is gonna turn heads..both while driving by and people trying to figure out what's going on! Yalls banter was funny af too!

[@BestDamnShopAround]

You're right, it's going to break some necks! Thanks, we cut up a lot more when there's multiple buddies hanging out!

[@THROTTLEPOWER]

Looking good, great vid!!!!

[@BestDamnShopAround]

Thank you, appreciate the support as always!

[@THROTTLEPOWER]

@@BestDamnShopAround 👍👍

[@stinkyriderx]

I’m ready to see these rockers shave themselves!!!

[@BestDamnShopAround]

I'm ready to see the first attempt of pulling it out of the driveway!

[@ryansmith2845]

OMGosh. I would have such a hard cutting those fenders and panels. However, that thing is looking badass!👍

[@BestDamnShopAround]

If it was a nice truck I would have a hard time as well! But with this truck being so bad and all of the body panels would have had to be replaced anyway if we went the restoration route I didn't feel as bad!

[@weldthatiron3683]

Cool truck

[@BestDamnShopAround]

Thank you! We need to finish it!

[@andyosteen1780]

I love this!

[@BestDamnShopAround]

Thanks brother! It's going to be wild!

[@LoudPedal66]

Sweet!

[@BestDamnShopAround]

Thank you!

[@lucillesgarage84]

Loving it!

[@BestDamnShopAround]

Thank you!

[@samdavis3813]

Congrats on the huevos to cut those panels. Even more props for the way it turned out!

[@BestDamnShopAround]

Thank you! It would be a lot harder if it was a nice truck haha

[@Accordingtoandyo]

Super legit!!

[@BestDamnShopAround]

Thank you!

[@mouthfarts6072]

Why not just put fender hood on and set tire next to it then trace the radius 🤞

[@BestDamnShopAround]

We tried that but the sharpie wasn't long enough. Later we realized i could have taped the sharpie to a ruler... Live and learn lol

[@SatoshisSon]

What's the wheelbase on that

[@BestDamnShopAround]

I can't remember off the top of my head, I'll look next time I go over there!

[@Joe-xj2tb]

Still didnt chop tha top

[@BestDamnShopAround]

Decided not to chop this one!

[@randy6350]

Sorry gentlemen but that’s STUPID low‼

[@BestDamnShopAround]

I agree! But that's what Andrew wants... I'll let him learn the hard way! Haha

[@randy6350]

@@BestDamnShopAround But why so low? Why not do air ride or hydraulics and a set 13” wire Daytons? He could gold plat the spokes in the wheels

[@PeterHatch-mx7zc]

Would watch but to much b.s talk

[@BestDamnShopAround]

👍