NEMA 17 Stepper Motor Control using L298N Arduino tutorial

Stepper Motor Control using L298N Arduino tutorial
Link sketch download : github.com/mak...
::::::::::: SUPPORT CHANNEL ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
Please Donate To Help Me Afford New Equipment And Software To Make My Videos More : goo.gl/1m8Dg2
Don't forget to subscribe!

[@DomBurgess]

Thanks for the video! I have an Nema 17 hooked up to a L298n and an Arduino. I have no issues operating it, but I'm having problems powering it. If I use a 5v 1a supply, it works but torque is low. If I use a 12v 2a supply, the torque is great, but the L298n pulses ever second or so which sends power to the motor. It doesnt appear to actually turn the motor, but it makes a buzzing noise which is VERY annoying. Do you know why I'm getting this pulsing from the driver?

[@festerbestertester2232]

Still an awesome video - solved my problem. More importantly, uses the best music track ever, none of that wack electronica rave junk that usually gets pumped out. Kudos.

[@douglanders5558]

Finally the first tutorial with actual code that works! I've been through a number of them where the code ultimately fails. Thanks!

[@caxio2]

Hello, my L298 gets tremendously hot as soon as connected to the Pins 8,9, 10 and 11 of the Arduino board. I use L298N with a Nema 17 45Ncm 1.5A 12V and identic wiring as shown by you. This has quite some effect on the step motor after 30secs that get noisy then stops working after 30secs. Thank you for any hint.

[@RonAdamsky]

Most of Nema17 work only with new drivers : A4988 , Tmc2208.

[@ghanshyamc463]

@@RonAdamsky I have the same overheating issue. Will using the a4988 solve it??

[@RonAdamsky]

Yes I tried with TB6600 and works great.With L298 Nema17 don' t move at all.My Nema17 motors have only 2ohm resistance of coil.

[@atulkhatavkar6986]

How to determine A+&A-&B+&B- mine is just vibrate and not moving. Nema 17 5.6kg motor driver and connected similar to you. Power supply 2amp 5 volt please help

[@suvobratasil4731]

Kindly tell me how to program stepper motor to make any specific number of revolution in clockwise direction and then the same number of revolution in anticlockwise direction continuously. And also how can I vary the speed of revolution. All the programming I am getting is about single revolution in clockwise and single in anticlockwise direction.

[@terrys824]

Now just wire in a variable speed controller and could be used on a camera slider?

[@sen168]

If I want to use the joystick to do real-time control, what should I do?

[@alfredh7108]

Thank you for this helpful informations! Please let me ask a typical "Beginner-Question": I want to include a Potentiometer or 2 Switches (clockwise/counterclockwise) for controlling the NEMA17. How is the best way to integrate/connect? Have I to Change something in the Sketch? Thank you for your helpful answer.

[@Lann91]

I'm sorry but you can apply ~35V on the 12V input? what?

[@blackfaithdoom9018]

I am sorry, i am wondering which model of a 3D-Printer we are seeing in the Video .

[@dablet]

has anyone gotten this L298N+Nema 17 to work with ESPHome or Tasmota? if so, could you please show the wiring diagram as well as the codes?

[@asimov741]

I'm using 5A 12V power source and 1.68A stepping motors, but they are only vibrating, tried all wires combinations, do you have an idea to make it work ? :(

[@nizarworld2020]

change wiring.coils are not in the same line .but across the board. i had same exp . now it working fine

[@asimov741]

Well i fixed it, that wasn't wiring but Arduino D8 which was in HIGH whatever I would program 🤔

[@nizarworld2020]

will u pls reply to my doubts

[@martienrurenga772]

hi, i'm having the same exact problem, could you maybe tell me how you fixed it?

[@joaocamiloulhoa4878]

it is possible to control microsteping?

[@theenlightenedone4738]

Great video........Check out my ps2 controlled car I used a l298n but the motor over heats fast any advice

[@kiranshashiny]

Did not work for me ! I think the newer motors need A4988 .

[@josephdavid8091]

I used an arduino i previously had used to play the game of thrones theme song on a piezo buzzer and when i turned it all on the motor started humming the theme song

[@bobsoto7131]

Unable to find the sketch. link is broken

[@lakshaynarayan1853]

Continously? Or Motor Will Stop After Sketch?

[@MakerTutor101]

continuously. dirStep = 1 to left , dirStep = 1 to right if( stepCount > 500){ stepCount = 0; if( dirStep == 1) dirStep = -1; else dirStep = 1; }

[@Jk-rm9sx]

Could you provide the parts used to incorporate the belt driven linear actuator?

[@eks2288]

How to connect 3 of L298's (3 axis xyz) with Arduino for CNC purpose? Is it possible?

[@atihrot755]

Je to možné ale treba zvlášt 3 ks ovládačov na každý krokový motor.

[@sydms36]

My stepper motor is vibrating but the shaft not rotating could u help me out

[@slathian1223]

I had this issue too. A couple things you could try: make sure the polarity is correct on you connections. Use a multimeter to see the resistance it should be .009 ohms. If that doesn't work disconnect your ground wire from your power supply and the arduino and make sure your PSU outputs a minimum of 3.5 amps. This will be 1.7 amps per motor phase.

[@RonAdamsky]

Try with another drivers ie. A4988 or TMC.

[@kudin8082]

@@slathian1223 what power supply I should use for stepper motor nema17 hs4401..?

[@RonAdamsky]

Not for low resistance stepper motors Nema17 , HS4401 doesn't work.

[@kudin8082]

for this stepper motor, what power supply need to use.?

[@marianpelmus]

my l298n gets very hot after just 30s of motor spinning, and i cant figure why :( i have a NEMA 17HS8401S same driver module, and a power supply 12v 5A motor spins ok

[@ivang.7526]

Dude, with the l298n the max is 2A

[@andrew_with_laser_eyes]

Still struggling? I can help you out

[@Dr.Sarkar]

@@andrew_with_laser_eyes I have the same problem, I have nema23 with l298n, the l298n gets very extremely hot after a few seconds..

[@memahrez]

@@Dr.Sarkar ln298 is rated for 2amps max

[@andrew_with_laser_eyes]

@@Dr.Sarkar Hi, If you're using a PS that is capable of supplying more than the 2A max of L298N, you can still use the power supply. What you'll need to do to make this work and not overheat/blow your L298n is to send a PWM signal to the enable pins on the H-Bridge. Start with a low duty cycle and increase from there. If youre driving 2 phases of a stepper with the H-Bridge, set the PWM to be the same for both enA and enB. Sending a PWM signal to the enable pins is used to limit the current passing through your L298N module. If you are currently setting the enable pins to HIGH, your essentially setting up a 100% duty cycle thus allowing the full current to pass through. If your current is not limited by your PS or by PWM, current will pass through and it is defined by Ohm's Law(ignoring induction of the motor). I hope this helps you. Have fun :)

[@luqmananuar791]

Sir... The link i cant access.. i really i need this sketch T T

[@zainnoor435]

Hi I needed some help with ardino sketching. I just started a month ago. I need some help with a project that i am working on.

[@عمرمرخي-ط2ذ]

شكرا انت فنانة

[@1yyymmmddd]

Pretty limited use project as it requires two power sources (5V and 12V).

[@gnanamanikandangopichandir1571]

I want use wemos instead of arduino

[@kenjimax73]

what type of this nema?

[@mrilhamtech6632]

LINK SKETCH eror.

[@mariangelamiranda8949]

May I know the holding torque of this motor?

[@hemanthnarayan373]

www.amazon.com/STEPPERONLINE-Stepper-Bipolar-Connector-compatible/dp/B00PNEQKC0/ref=sr_1_2?dchild=1&keywords=Nema+17&qid=1590211554&sr=8-2 You can find the user manual in the link;

[@gabrielsantos19]

Nice

[@MrHomyachek]

Как к нему подцепить мотор сканера чтоб играть музыку?

[@ibaadulatqiyaatkj1214]

thanks i like ittt

[@sarthaksarode3982]

Nema ke wires l298n ke konse port pe jayege like in 1,2,3,4 kon tera bap batayega kya, agar video dalni to thik se dal

[@Guerra_automacao]

parabens. top obrigado

[@FaheemYaseen-tb8gz]

Hy nice

[@ناقدطعام]

thanx it is nice

[@mustafatunc3903]

Thank you

[@rethom9427]

no picture, kein Bild

[@hmeydesaid9327]

so nice thanks for helping .....

[@alistairbalistair9596]

thank god for the mute button

[@이승우-e3p]

Coding please

[@nizarworld2020]

Nothing informative

[@АлексейЛебедев-з7в]

Молодец милашка