Nesting parts in Cypcut for laser cutting (english)

Showing the nesting utility and how to setup compensation for laser kerf. We are actually making a product in these videos, and the videos are being made as reminders/training videos.
Laser being used is from Bescutter.com

[@andy123law]

Thanks for sharing your incite on cypcut. Very little info out their in English keep it up guys

[@SuzukiGsxr7500]

Hi. Cypcut nesting function plate number limited to 20. How nest part on more than 20 plates? Thank you

[@DISEÑONADALIN]

Hi ! I wached your video for learn about to how i do for use the program . Thank you ! But i .have a problem: after to make the setting , (count of pieces, plates, geometry expanded), when i do the nets, cypcut showme the next : "Size plate is too small, no parts add to nest" ..Im sure that the size plate is not small, because in the setting plate i have size of a 1,5 meters x 3 meters.. Do you know wich is the problem?

[@barrykirwan2109]

Can you tell me how you rotate a part before cutting ? Need to rotate a part 90 degrees to fix into the sheet. And im stuck on how to do it

[@9633224669]

hai, i am facing a problem in cypnest, when i try to nest diffrent parts above 50 it shows 'quantity has reached upper limit error'.how to change it?

[@highlevel2022store]

Hello, this video was very useful, I'm actually working in a metal pieces factory and I have the responsibility of Nesting Process, I got a big doubt is possible to program the nesting in other computer and then get it in a usb to load it in the laser pc? Thanks for your help and your video!

[@smallshoplasers8785]

It is possible to nest on another computer and save as a laser document then move the file with a USB drive. You would need the same software on both computers so that the files could be shared.. Cypcut is available for purchase, and it is possible the machine dealer could also supply an additional copy of the software... Ideally you would have a copy of the same version.. There are also more powerful nesting software types that require more powerful computers to get increased yield from each sheet, if you are in a factory it is likely you would benefit from more expensive software to reduce waste of metal.

[@highlevel2022store]

Thank you very much, it is good to know there are persons who don´t think twice before answer a question. We´ll keep in touch, thanks for your useful help!!

[@RinkuYadav-qk1he]

Can you please make video for round or square pipe cutting .

[@Dogamontessi]

Hello. In case of pending motion out of range, how is the procediment?

[@WaleedWasfy]

Very helpful, thank you and keep it up

[@Dave1981]

This is really helpfull. Thank you!

[@MultiFd3]

hi, my cypone only can nest 100 part, do you know what is the problem? thanks

[@fernandosilva1252]

Qual melhor foco vc usa no aço carbono 2,65mm no ar comprimido

[@Donato481]

Ola vc poderia me ajudar

[@aleksej6002]

Thanx for the video. What's the name of your machine?

[@smallshoplasers8785]

Mine is a Bescutter. They are a US based importer of machines, but they work with many other countries as well.

[@sevilsoy1590]

Hello, help please Where can i make a common cut?

[@RitikMahajan-i2z]

hi, in my case when i am going to nest it shows size of plate is too small. can you please help me to fix this error

[@DISEÑONADALIN]

hi how are you? Could you fixed this problem? I have the same

[@rashwanmohamed4545]

Thanks!

[@mohammadibrahimselo8236]

Hi my friend How to calculate the compensation of dimensions I have drawn a box length of 1000 × 1000 mm but after the story did not give me this dimension, but less I want help

[@heshammansy1585]

he mentioned in the video that you need to try at least one known dimension square to cut then measure it and see how much less the actual dimensions are , then add half of it as a compensation

[@industrial.inoxidable]

hello friend .. I've been following you closely with your videos I think many people and I are very grateful and I would like to ask you to publish a video about how to calibrate the height of the head and the graduation of the lenses that go inside the head, something like that will be very helpful. Thank you friend, thank you very much.

[@smallshoplasers8785]

We made a few videos for calibrating the head, and changing the protective lense.. I just need to get the time to put the videos together.. I'm doing these when I have free time.. I happen to have a laser, I'm not a laser machine sales rep, hence the slow pace of videos being made.

[@industrial.inoxidable]

Friend, however, it is of great value what you do for having the good will to publish your videos as they are of great help to many people. we will be waiting for more videos of you., thank you

[@thermaltech2359]

TIP TOUCH Alarm in cypcut please find the solution Raytool cutting head we using

[@smallshoplasers8785]

It helps to calibrate the sensor with the vent fan off, and to be sure your metal slats are reasonably clean and reasonably flat, also wipe the tip of the nozzle with a clean cloth while using blow to remove metal dust.. Next is to use tabs to hold larger parts to avoid the parts from tipping and bumping the head.. Even still it is not unusual to have the sensor trip once per three or four sheets. One thing that can help solve the issue is to point a camera at the laser as it is cutting to record what happens before the alarm sounds.. That way you can solve the issue..

[@smallshoplasers8785]

See the video kzbin.info/www/bejne/qYvCmmSricqopbM which shows how to calibrate the sensor. That may solve the problem.

[@swapnilpatel4642]

HOW MANY PARTS WE CAN IMPORT MAXIMUM IN CYPCUT?

[@smallshoplasers8785]

I have not maxed out the parts library, but I only cut 10-15 unique parts at a time.. I'll try to see if I can find the limit. You are limited to 999 of each part at least with my version of cypcut.

[@mhammedmojahid1540]

hell my fraend plese send me software cyplaser cutt

[@kon5060]

cho em xin phần mềm này với ad

[@smallshoplasers8785]

Google translate shows the above as Vietnamese " Can I have this software please, admin?" I only have a single installation of the software. I am just a person that uses the software. I don't sell it.

[@lasmiansitumorang81]

Hi all, can share this software? thanks

[@smallshoplasers8785]

I'm fairly sure that the software requires a license key from the manufacturer to use, I'm just a guy who owns a machine that uses the software and made the video to be helpful.. It should come with the laser machine it will be used with anyway.. I have had the laser machine for about a year now, and have always programmed the sheets on the machine.

[@cevikramazan5570]

Türkçesi yok mu anlatımın

[@smallshoplasers8785]

Sorry I only know how to speak English and even that is questionable at times. I suggest going to the machine maker for information in your language .

[@aymanhessn5969]

مفيش شرح عربي ؟

[@smallshoplasers8785]

Sorry I barely speak English well I would make a mess out of Arabic..

[@sohail01101]

@@smallshoplasers8785 AMAZING TEACHER THANKS ALOT

[@AnshuKumar-qk3sc]

Hindi bolo bhai

[@vipinjangir8589]

Hello Please can share this software?

[@smallshoplasers8785]

The software is bundled with the control boards for most lasers. If the software can't see the control board it won't work.