New 2 post lift installation Atlas BP9000 its finally up!

The new Atlas BP9000 is finally up! We ran into some setbacks however all and all things went well.
There will be more supports added in the near future already in the works. When bolting to an unknown there’s that safety factor that plays with your mind, we had the minimum requirements however I don’t know the integrity of the concrete it appears ok. It’s hard for me to except. Therefore we will be adding a upper support beam. Know that I have access upstairs we found we have the space to go through the ceiling placing the cross beam out of view not effecting head clearance.
I captured a couple repair vids I hope to have up this week as well. Fell behind with everything going on. My apologies, Hope you enjoy

[@jonasgrumby1093]

This is like winning the lottery, you will have a bunch of people wanting to be your friends

[@deathwrenchcustom]

The reason for the hole and the "slot" at 2:52 is to make manufacturing cheaper. The holes are not drilled; they're laser cut. Laser cost adds up by the minute, so anywhere you can cut a few seconds really pays off when you're producing thousands of parts. Doing it that way saves time, because the laser doesn't have to make separate pierces for the holes; it is part of the perimeter cut. Now you know! :)

[@palmillos61]

I like watching you work on cars. It gives me an idea of what mechanics do to work around parts under the hood. the last time I asked about how to fix a rear view mirror that fell off for no reason. I watched you do it, and i followed exactly as you said, and the rear view mirror has stayed on for almost a year now. Thank you!

[@DAKOTANSHELBY]

Happy to see you no longer need to work only with Jack stands and creepers. Thanks for your video series on the Jeep AX15 Manual Trans overhaul. I used it to completely rebuild my TJ AX15 5 spd. Your video was the best one on youtube. Thanks again.

[@klc317]

Looking good. The most useful thing in any shop for sure.

[@robinsonsauto]

klc317 thank you, I agree it sure makes life easier

[@joecorrie1]

I’ve had a bend pak lift for years this is built very similar to it, nice hoist.

[@shanet1839]

Thanks for the video!! It was far better than the manual. Really appreciate it!!

[@mikesgarage1518]

Thanks for posting this, it was very helpful. I just installed a similar lift (BP8000) and the install steps were the same. Your video was way better than the installation manual!

[@dc5723]

What a beautiful shop, esp with the new lights and lift.

[@ericcorse]

Fantastic Will I hope it gives you years of service.

[@robinsonsauto]

Eric Corse thank you, I hope so too

[@northernjoethedroneguy1378]

In the process of installing ours now. Good video and thanks for sharing.

[@shitloveaduck]

So nice! I have an atlas in my man cave as well. It’s great for restoration projects. I mostly do trucks so it’s easy to remove the box and cab, put them on furniture dollies and have a rolling chassis to restore! No better way to do it! Start there, get all your suspension done, r&r the motor and transmission with much more ease. It’s so much better than jacks and jack stands I used in the way too distant past!! Heh heh. Nice shop you have there!

[@georgespangler1517]

Nice lift,,,I bought a new Aplus 10,000 lb capacity,,,, and a week later found a Globe on market place,,,there the Canada made Cadillac of lifts, and stole it for 300 dollars, couldn't believe it,,uses but in great condition, and a beast, now I have 2 lifts for 2100 dollars, it's like having 2 more bays in garage..love when people don't know what they really have. Enjoy your lift...

[@ManicMechanic007]

Oh yeah! This shop is gonna be great!

[@robinsonsauto]

ManicMechanic007 :) thank you bud

[@JasonBolte]

Thanks for sharing! I'm going to be buying a hoist in the next 12 months.

[@cedicol]

I'm happy for you bud. Your really going to love that investment. Keep them coming because we love em.

[@robinsonsauto]

cedicol thank you, feels good so far :)

[@johndempsey8643]

Thanks for taking the time to produce such an informative video!

[@montehyler]

Another great video! Good to see you add a lift to your new shop. This should make a lot of jobs much easier for you! Congratulations!

[@robinsonsauto]

Monte Hyler thank you for the kind feedback, it's making life easier already

[@joelmccoin9727]

You are on yer way now......looks great, be safe, stay well.

[@robinsonsauto]

joel mccoin thank you, will do :)

[@markdorman52]

Just bought one, thanks for this video, it was very helpful!

[@wysetech2000]

A job well done, everyone involved.

[@robinsonsauto]

wysetech2000 thank you, will pass the complement along

[@ronbaynes179]

Nice job Will. Your shop is really coming together.

[@robinsonsauto]

Ron Baynes thank you for the kind feedback, it's appreciated

[@rogs926]

i am very happy that you got a new shop and lift great job keep up does video great job

[@Robert-vi6tb]

Hmm. High pipes and hard concrete.... Glad to se you have a new place with lift and light.

[@RaoulThomas007]

Very exciting! How cool is that!

[@robinsonsauto]

Raoul Thomas thank you, it's really cool

[@haywardsautomotive6156]

Nice lift Will...shop is looking good!

[@robinsonsauto]

Hayward's Automotive thank you bud

[@E550Boi]

I was going to comment that you put your arms on backwards as the shorts always go towards the front of the vehicle. LoL However, with the Eclipse being backed in, I see what you were doing. Great work>

[@dakotaboondocker8740]

good job on the hoist! And awesome rally shirt! SoDak proud.

[@TexasPLNR]

Good job! I know you'll be happy w/ that lift.

[@robinsonsauto]

Texas Pipeliner thank you, enjoying it already :)

[@rjcook4051]

Thanks for walking through the process. The installation manual is very vague

[@nicknicu1787]

Well done! 👍

[@robinsonsauto]

Nick Nicu thank you

[@JohnKaufmann]

Great video man. Almost every hoist install has its own little bit of extra drama. mine too! Enjoy!

[@joeysogness2323xxx]

Love the video will as allways thank u

[@robinsonsauto]

joey sogness thank you bud, hope it serves us all well

[@hugoramos731]

Good job 👍👌👏

[@bobkout]

Awesome! Best wishes.

[@georgespangler1517]

Nice! My lift is coming next week,, I'm excited, no more laying on my back, last year a car roll off ramps on top of me,,broke 3 ribbs, lucky it was a jeep and I'm thin,,would have trapped me if not.. I got the Aplus 10,000,,, with double s bend beems,,but has your lifts arms,,,it was a hard discussion.

[@SteveRobReviews]

Nice setup. I'm thinking the bases with the slots for each hole was cut on a plasma cutter or water jet and its easier to start your hole from an outside edge than plunge cut the hole. Cheers !!

[@robinsonsauto]

STEVE ROB thank you bud, I was thinking maybe that was it. Thanks for the feedback

[@samd410]

congratulations. you deserve it.

[@robinsonsauto]

Sam Daik thank you, I was over do on this one, well earned my back kept reminding me

[@mitch500]

The double nuts on the cables are both supposed to go on the bottom, according to the instructions

[@majorsmackdown]

10:00 - that cracked me up !!!

[@robinsonsauto]

majorsmackdown 👍😆

[@stephenzies8867]

Good Job !

[@spiderdad00]

Great video

[@chadgdry3938]

great stuff.. thanks for sharing that..

[@robinsonsauto]

Paul Gdry thanks, my pleasure

[@alioman26]

Nice work

[@RichBurn]

hydraulic lines are supposed to go in a separate tray under the ramp. did you not get one? the cables will rub through the hoses like that

[@hydrogenman1000]

Looks good

[@jibmaster]

Just bought a Atlas 8000. I was searching around for a good install video and came across yours. Nice work and THANK YOU! (BTW how are you liking it?)

[@pinoag4857]

good job man

[@angelrivera2661]

Kool men

[@hawaiianf1504]

I want one!!

[@Cattachmore22]

Beautiful :)

[@robinsonsauto]

Donald Bain thank you

[@billrimmer5596]

Racks r sweet!!

[@TomekinaOfa]

did you ever have to replace the arm restraints? if so how did you do it? especially the small one thanks.

[@mr2law]

Thanks for sharing! How is the lift holding up?

[@billsenke327]

How has the lift been holding up

[@larrykay6606]

22:01. “Time for our fist lift...”. Ouch!

[@scottryan9845]

Can't figure it out, call big Al he can figure it out

[@joselitorodriguez5981]

Enjoy the lift

[@robinsonsauto]

Joselito Rodriguez will do, so far so good

[@JT-dx1qk]

I'm looking to buy that same lift , how is it holding up ?

[@1bmwrider]

Curious why you went with a floorplate lift? Nice video, Thanks.

[@builtbyscum3313]

After 4 years, how has the chain over roller treated you?

[@javierr1blue]

THANK YOU FOR THE VIDEO. IM IN THE MARKET TO BUY ONE OF THIS. BIG HELP!! PRICE ? GOD BLESS

[@chamarystigers8731]

My brother have one at home big shed

[@icefishingmn5879]

How do you like your atlas lift? Did it give you any problems? I'm thinking about getting a bp10,000 lift

[@icefishingmn5879]

How do you like your lift? Did you have any issues with it? I'm thinking about getting the BP 10,000 lbs

[@johniec2]

Great video, I'm looking into getting this same lift from my local Greg Smith here in Atlanta. Any advice you can share? Is the new lift working out good? Thanks...

[@mousegouse]

👍👍!!!

[@robinsonsauto]

mousegouse thank you

[@smokeshow973]

I'm thinking about getting this lift how is it holding up any issues thanks

[@brucewest3516]

Did you add extra brace across the top?

[@wacc7365]

What is the heaviest vehicle you have had on this lift?

[@nicosmoorenburg9000]

What are what knots?

[@corellita9]

that elevator can lift vehicles like dodge ram 2500?

[@icefishingmn5879]

How high is your ceilings?

[@KKhhoorrnniittee]

What's that red thing on the table at 4:55? (-;

[@robinsonsauto]

Сергей Луцкий good question.. it’s a 2 part Epoxy application gun.. I used special epoxyEpoxy with the anchors

[@KKhhoorrnniittee]

@@robinsonsauto Thank you, sir. I was about to think of that when you replied. I hope the lift is doing okay so far?

[@robinsonsauto]

Сергей Луцкий your welcome. It’s been great

[@toordog1753]

You're professionally installing this and it took an engineer to tell you to not set it on a concrete pipe?

[@robmontagano8117]

what's the recommended concrete thickness ?

[@robinsonsauto]

4" minimum 6+ is ideal

[@nicedinger2650]

robinsonsauto I thought you said that your concrete is only 3.5”. Did you add more concrete

[@jasonmushersee]

You bought the nice big one! Bet it could lift donald trumps ego.

[@robinsonsauto]

jasonmushersee hahaha needs to fit through the door first lol just playing funny though

[@robbypro3370]

This is a man's job stay out of it women.

[@theonetheonlyw5483]

be careful using these cheap Chinese lifts.

[@hydrogenman1000]

Atlas has been around for years

[@MrPatdeeee]

Every thing was great; EXCEPT for that infernal, satan-led, "NOISE" called "music". Why do video makers have to have this atrocity? WHO needs it? Thank Jesus for "mute" buttons. America is going to hell in a handbag; and that horrible so-called "Music"; which is really nothing but "offensive" noise; that began in 1954; because of an UN disciplined punk by the name of Elvis; that satan used to destroy EVERY thing that was moral, decent, chivalrous, honorable, modest, proper and righteous; has led to the total end of good Music; is part of what satan had done to America. Oh indeed YES! Slam, ridicule, ostracize, cajole, castigate, demean, belittle, attack or crucify me, all you want. But one day ALL will know just how bad this once "Nation of Righteousness" has become. For it began as THE greatest, THE most blessed, THE most righteous, THE richest and THE most powerful nation on earth; but is now nothing but a cesspool of dunghills; from coast to coast and "non" border to "non" border. So let it begin with your attacks against some one that has the courage to tell the truth. For this "noise" played at 3 times the level is should be, WILL ultimately help in bringing on the end of all satan-led, Godless foolishness's that has permeated every facet of what our "founding fathers" created. They are turning over in their graves. May Jesus have mercy on this nation. So flame away. They nailed Him on a cross 2,000 years ago. So why should any "born again "Christian expect any thing else? Thankfully, one day we will not have to put up with horrible noise called music; as forever never a tear, pain or death; not to mention "noise" paraded as music, will ever be again. Praise His holy name. But woe be those who accepted this garbage that an evil punk began; that most of the world has bought into, "hook, line and sinker". satan has never been happier! MARK ME WORDS!

[@phillipardell5579]

I'm concerned that someone thinks that a little finger pickin' is gonna bring down fire and brimstone.