New Arrma Outcast 4s V2 I KILLED that little 2400 KV Spektrum Motor

[@sensi42000]

Killin it with the initial vids on this truck! It's great to see what the car can do but a lot of us like to see the weak points and quick fixes so we can spend more time bashing! Rock on👍

[@earlmoorhead5555]

I’m sure the sand is killing that bearing but if arrma would have listened they could have put a sealed / shielded bearing in there knowing it’s collected dirt there in the past to stop the failure 🤷🏻‍♂️but good thing is we know and it’s one more item to replace before we run are RTR outcast4s ( ready to rebuild) 👍👍

[@crazyivan512]

I doubt that Arrma has any plan to upgrade the bearings they purchase, ..they obviously sourced those bearings from whoever they buy them from with the intent to get them as cheap as possible to keep their costs down and then just tell the customer.. "we dont recommend the vehicle be run in a dusty environment" and will not warranty it . I personally will never buy an RC I have seen have issues and think to myself.. "well I'll just replace the motor bearing before running a BRAND NEW.. RC" .. they wont get my money if they arent willing to improve their product.. they could just raise the price by 10 bucks and cover the cost for good motor bearings

[@jeremytrc3171]

Oh snap, Earl , ain't even have the rc yet and I'm already planning on working on it 🙃 😅

[@Johnwick-ed7vo]

@@jeremytrc3171 yeah these days I buy bearings, antacids and aspirin before I buy an arrma lol 😂😆 bearings cause we know they suck, antacids to take away the heartburn after I pay for the before bash replacement's, and aspirin for the celibritory first complete week of no break's 😆😂 I really don't like what I am feeling and seeing from arrma these days sorry guys been with them from the 2 wheel drive days but they worry me

[@chadbiermann3380]

I've had to replace the pinion side bearing in 2 separate 3200 kv motors so far. But have been running 4 3200 kv motors for almost 2 yrs. I changed them right over to the TRB rc bearings. Haven't had any issues since. But whenever I'm doing maintenance it always something I check for now. Great video!! 💯

[@NathanStorer-RC]

One thing I've done to help with the sand in the motors on those BLX vehicles is put high heat tape over the holes on the motor that aren't being used. That transmission, like you said, allows a lot of debris into that area in general.

[@stefanm.4416]

To prevent (most of the) dust from going into the motor take some glue (i like to use the ones who stay flexible) and close the holes where the tree wires come out. Do this from the inside so it will be clean and not noticable from the outside.

[@SlooDon]

Thanks for the content! Showing the motor repair was very helpful.

[@RCvapor]

I put some green slime on the bottom of the spur gear case before sliding back into the chassis, this seems to stop grit getting behind, it also makes it easier to take out too.

[@meirdeaph]

I think its the perfect size for your backyard track. I know it's gonna be awesome when u bring it back to life

[@RCCREWNJ]

Thanks for the info! I'm looking forward to ripping my Outcast V2 when it comes in!!

[@rcguygarage]

You're going enjoy it

[@robertsmida9601]

Well because of you and Earl Moorhead, I've been looking at getting an Outcast. I just need to figure out if I want the RTR. I may just get the one I need to add the electronics. My rc's are almost all Traxxas, I do have 2 Losi LMTs.

[@rcguygarage]

The RTR version of this is not bad It's what I had and I loved it 👍💯 matter of fact still do It's just going to better power system in it now

[@robertsmida9601]

@@rcguygarage I haven't made it yet, to where you go 6s motor, just watching videos when you first got it. Almost bought Losi drag car, on sale $300, would be mostly shelf queen like my Traxxxas M41

[@rcguygarage]

Hey NOTHING WRONG with collecting SOME of these RCS for sure

[@EXTREMERC416]

I dont feel confident reusing a motor that exploded a bearing. I saw motor windings broken and in places it shouldnt be near the bearing slot. I asked for the warranty replacement everytime to be safe

[@EJ-74]

Yeah definitely need to put a shielded bearing in. Cool vid Guy 🔥👍✌️

[@jeremytrc3171]

Guy, now I'm worried 😟, I've ordered one of the outcast, Whats up with Arma and there bearings, had a similar problem with my Talion , but it was the wheel bearings that fell apart before I got through my first pak..... wth... but at least they warranted them.👌 🤞 👍👍👍 thanks for the warning, gonna have to keep an eye on bearings when I get her.👍👍👊💯

[@EXTREMERC416]

My blx 2050 shaft seperated there was a gap moving between the aluminum and the yellow wrapped stuff. I put a spektrum 2050kv i had as a spare. I have no clue how it happen. My hobbyshop told me The motor core will start to spin on itself

[@johnlujan8706]

Good work. I just purchased one of those too and I hope I don't have that happen to my rc. I think I'll save this video for sure. Thanks.

[@johnstogsdall8582]

I agree your paying for a higher quality part that should include higher quality inner workings as well

[@kevinporter]

Keep the videos coming guy 🤟

[@billmason3314]

Hey I watch all your shows really enjoyed this one you should do more of these T-Bone racing makes mud guards for these I have a nortorious 6s and got a reedy fan 40 mm for the motor big time difference also got a inner cover for all the electronics etc to keep all the debri out works well but keep up the good work

[@sambagogo777]

I very nearly pre-ordered the new 4S Kraton a week or so ago. Seems I dodged a bullet!

[@just-in-time6069]

I've haven't had that issue with the V2 big rocks I got my kids witch I did buy bearings right away heard that was a issue but they don't run much more then a pack through them before there done now there update to v3 version I got right before the v3 came out go figure but have had any issues with blx 2400 that I've have thrashed in my Typhon 3s now running a 2400 3674 wich keep it light tons more go or 3674 2250 6s that's nuts and not as hard on the mount I do have 7075 motor plate saves a lot of weight compared to the big 6s system should try its better in my results .keep up great work and have wonderful day.

[@dustinfowler7868]

M2c motor mount for the 3s line stops dirt from entering into the spur gear area,don't know if it fits 4s v2,but it looks like it to me.

[@rcguygarage]

Yes I have one🤫

[@mitchellrooks9547]

Love it man keep it up 😊

[@Johnwick-ed7vo]

I'm sorry about the bearing issue as I don't think there is any hope for this issue at the moment, I don't catch all the tidbits of information from arrma but I have a decent pool of people that tell what they can, and yes I indeed am worried about this new 4s line just little things that don't seem to have been thought through and then rushed through testing on their end, 2 of the most obvious examples are the drive shift I think on the wheels they are hitting the shock springs might not be a issue up front but I'm willing to guess it will cause issues down the road, at least spring issues, and who knows mabey dive shaft issues, there is another first run sign that leaves marks on place it shouldn't but I am not remembering it at moment um I think u pointed it out as well, but agin It might be nothing to worry about, my deeper worry is that production model will have the same careless thought put into them, just because there is a paper that says it will work does not mean, it will. Ok agin I'm sorry about the motor bearing it in my opinion is just another troubling sign that arrma is not the kind of company that they once were, I just don't think spectrum is the thing they should go with and I to almost always switch out motors and speed control often but not always I switch my radio and receiver out to a Dumbo to be honest, I also agree, when they pulled the blx systems from their rigs they lost a big support piece of their business, heck I'm still buying blx systems as often as possible

[@wallacengineering8096]

Ya that Diamond Dust of yours really hates bearings, this is like the 4th video ive seen on your channel doing the same thing with these Spektrum motors LOL. You can give the dust a way out with Rich Duperbash's mod - he dremmels a hole in the chassis underneath the spur gear to allow dirt and debris to exit the center transmission area. Seems like a good idea, think Ill do it on mine before running the truck.

[@rcguygarage]

This module was said to be better sealed on the box so that needed to be seen before doing my modification to that area of the chassis 👍

[@wallacengineering8096]

@@rcguygarage Ah ya good point, well it failed the test 🤣

[@fergsrcenjoyinglife352]

? What do you think about the battery compartment? Im going to cut a block of word to put in to it against the battery so the bsttery does not slide and bounce around. Do you have any other ideas for this issue?

[@rcguygarage]

Strip of something as a cushion. I've used rubber roofing, foam and sheet metal just depends on what's on hand

[@bryanharness1122]

Cool toys for sure. Enjoy mine.

[@fishnrc294]

Maybe you think what significance does a video like this have? I’d say invaluable as I watched it was interesting that the motor pinion had a C clip on the end. This is why I have a Losi Lasernut & even with lock tight the pinion keeps coming loose. It’s good for a few runs then comes loose. It has spectrum electronics & the motor doesn’t come with a clip to hold the pinion? I’m curious why is it just older. I just took it apart & re did everything so I can drive it again so I’m happy for now. I saw you getting some good air with yours so far mine has broke every few times out but now things seem to be ok except the pinion coming loose🤨

[@rcguygarage]

Wow I appreciate that👍

[@AlexHT100]

Well and truly frazzled 😂🤠

[@joecole511]

Any issues with the pinion gear? I have a V2 for about 6 months, never jumped it and have only run it on the pavement and turf & grass football/soccer fields. The other day I went to run it and the pinion gear was stripped. Thanks

[@jessjoshwyatt3571]

Arrma is definitely making me lean toward Traxxas!

[@rcguygarage]

that can happen but ill tell you that this truck RIPS

[@rcjunkie260]

When I ordered a blx Granite for one of my kids I also ordered a ceramic sealed bearing. Plastic still on the body and bulled the motor and changed the motor bearings. I think the 4s line is too heavy and powerful for the clutch plate design and the cheap aluminum used!!!!! Someone needs to make a steal set of clutch plates!!!!!

[@rcguygarage]

I have a 7075 one ready 😳😜

[@justincase948]

This is why I really like ur chan cause of the info u put out 👍👍👊🏻👊🏻pros and cons . I really want to get this 4s , just really strapped rite now ..

[@rcguygarage]

I'll tell you granted this may be too early but I have had a ton of packs through this thing I would definitely not have a problem laying down the cash or at least saving up for it

[@justincase948]

@@rcguygarage Thanks for the info on this truck 👍👍👊🏻👊🏻, I have been trying to save up for the last purchase of the year for me and it’s perfect that it’s 4s just cause I think 4s RCs are the best n Just perfect for power and the weight as well .. But anyway I try to buy 4h RCs a year … this year has been tough for me ,been having a really hard time getting materials for jobs .. is what it is… So great info on this and it will be my 4th truck for 2022 .. One more thing I just finally finished tekno mt 410 and wanted to no if u have one or ever had one ??? See this is why I don’t have a chan cause I just babble and babble …. And don’t change u or ur vids 👍👍👊🏻👊🏻 oh ya Moorhead is jellies on ur JAG lmao … keep on keepin my friend

[@barbedwirerat661]

Nice technique for extracting that outer bearing race from the can! I would not have come up with that approach on my own. I'll be storing that technique in my bag of tricks (which isn't very full LOL), maybe I'll need to use it someday.

[@malsmith2012]

Awesome video mate , thanks so much for showing us how to fix it. I love Arrma but this isn't good enough on thir behalf especially when they know about it. Just curious have Arrma/Horizon approached or spoken to you about this issue and said anything about fixing it? Keep up the great work loving the vids..

[@rcguygarage]

Yes they have the updated part I believe in it's way now as a mysterious tracking number appeared in my mailbox

[@lukerecore3211]

Ya I hear a guy, that's exactly why i buying a blx esc and motor for my granite v3, and not the spectrum one. Don't get me wrong I like there batteries and the chargers, but ive seen a decrease in quality from the "toughest" name in the rc game

[@owen8538]

I started running 6s esc motor esc on 4s arrma I found the 3668 motor get s far to hot and I burned an esc tho I was running 2800kv 3668 spektrum on the 120a esc

[@rcguygarage]

@@owen8538 6s ESC running 4s the power delivery is all that's needed. You can't run nitrous for a daily driver unless you want to burn something up 👍💯😜

[@owen8538]

@@rcguygarage I run it on 4s tho 6s esc motor and esc

[@rcguygarage]

@@owen8538 what burned and why

[@rcguygarage]

@@owen8538 there's missing info

[@rcguygarage]

I think mine is running HoBao 2200 or 2000kv I believe

[@xod7861]

Out of round spur caused lots of problem why do all the spectrum motors do this .. mine did the same thing bearing failure .

[@rcguygarage]

I believe debris accumulated as to why I put a hole under the spur to let the sand out

[@ronniecreason7870]

What do you think about fast Eddie bearings

[@rcguygarage]

I use them frequently

[@Frankredline]

Gread vid and info man learned alot.

[@reid9041]

Think this cud be converted to 8s with the 1250kv 160a combo?

[@rcguygarage]

Not for very long but I like your style 🤣😂🤣😂

[@winstonoso5821]

Can I put a 2100kv kaiju motor in the outcast v2? Will that work or not?

[@rcguygarage]

It's not the KV it's the size of a can

[@supermanjjm1982]

What size bearing is that ? I just killed one of the 3300kv motors

[@christiansrcs7789]

i thought i got lucky with my motor but no.. 😂 after 1 YEAR it died! pretty impressive but it still broke got some bearings off eaby and they are sooo good i forgot to say PLS change your pinion gear to hardened steel i haven't yet 😂 but ive stripped mine 3 times when that motor mount bends that gear destroyeds the pinion gear i had to get a new speer gear :( it was 30$ the hot racing one it's so good and my motor that came with the v1 kraton 4s the back blew off 😂 so my rc is running on supper glue been like that for 4 months i really need a new motor but the price for one 😭😭😭 so expensive when you collect money from birthdays hahhaha

[@51-FS]

Aint the motors like less then 80 bucks?

[@christiansrcs7789]

@@51-FS yeah some where around that price i found a good deal for 60$

[@51-FS]

Yeah rc stuff is so cheap.

[@51-FS]

I'm running a 1900kv in my arrma senton 550 mega...... with a 130amp esc

[@christiansrcs7789]

@@51-FS OMG 4s or 6s 😂 must be a beast

[@rceskimo8229]

Cut out some mud guards for the rear a arms?

[@rcguygarage]

Yes👍💯

[@Mexneck.media2023]

Where you get that lighter

[@rcguygarage]

amzn.to/3atG1bg

[@rceskimo8229]

Maybe a rock got jammed up in the out drive snatching that metal band

[@rcguygarage]

You're definitely onto something there. 👍💯

[@runnerbaba]

Are the Shocks better? On 3s the saft pops out on the bottom, because it is just clued/melted in.

[@rcguygarage]

Shocks are super plush and ABSORB HITS VERY WELL the light weight of the rig helps

[@mike-yc8bi]

These are like all the newer shocks vortex an newer cars they are built more traditional where the eyelet now is replacable

[@EXTREMERC416]

The problem is the power module and the dust its creating.

[@rcguygarage]

Yes that has been remedied 👍💯

[@EXTREMERC416]

Genius

[@rcguygarage]

?

[@MoStaxxEntertainment]

they should use hobbywing instead,i have no problem at all with those. spectrum is junk.

[@roberttruesdell6151]

It’s all about cost. They won’t put a high quality bearing in there because it cost to much. On top of that most people won’t be changing it they will replace the motor. So they get more sales that way. Spektrum gear is over priced garbage. But the key here is to replace that bearing before it fails and it will be much easier and no down time. Lastly, that was way to much loctite on that pinion grub screw!!! Just a dab on the first two threads is all that is needed.

[@rcguygarage]

I've found with the loctite I use I've had good luck using it the way I have for years with automotive applications as well👍

[@roberttruesdell6151]

@@rcguygarage automotive yes I agree. But with these small screws it doesn’t take much. Many people don’t realize the need for heat either. Glob on the loctite and then use subpar drivers and stripped screw and/or broken driver tip.

[@onemansvideos2134]

i like the 2050kv OG motor

[@rcguygarage]

Yes 👍💯

[@miked5789]

Why go thru that? $25 gets ya a new Chinese 2200kv 40xx/42xx....used em for years. If you fry them, get another.

[@rcguygarage]

Because it's a repair video some people would like to see it done and it's informational. Not everything is bang boom smash crash explosions sometimes it's real world stuff 👍💯😜

[@Nathan-qt2zi]

Hopefully these are just pre release problems

[@rcguygarage]

That's what Arrma is saying in communications 👍💯

[@rcjunkie260]

I've had my 4s for almost 4 years. Been changed from a outcast to a kraton. I've had it with the clutch system (on 4s only). The rear side of the clutch is a problem!!!!. Weather you buy a replacement set of clutch plates . Out of center and the way it cracks and falls apart I've been using the inner racer part of a old bad bearing I take 2 apart just for the inner racer. I put 2 of the inner racer parts and slid it over the back end of the slipper clutch and over time it still cracks and falls apart. Twice I ordered new clutch plates and the came bent amain sent me new clutch plates no problem. WHY?🤦‍♂️ 4s is to heavy and powerful for the 4s line!!!! Clutch plate is too weak(cheap aluminum no good!!!!) Max 5200mAh to 6000 mAh to keep weight down.

[@rcguygarage]

See this comment KZbin HID I'm just seeing it now. No notifications

[@rcjunkie260]

No problem 👍 I know Horizon now has a metal cap on it. Over time it might crack and fall apart when taken apart for bearing maintenance. Maybe not. The back clutch plate.

[@calvinwolf7107]

How did you take the trans out, the manuals from armma are complete usless and don't explain anything, and there'd litterly 0 videos

[@rcguygarage]

Remove single screw underneath chassis that's attached to the red block between the center spine and the motor mount, remove one side Tower to Tower brace, swing away, compress drive shaft to remove, swing rear battery stop to remove red block and slides towards battery tray area, pull up center tab (looks like half of a butterfly wing) gently use some type of a pry bar to push module towards ESC or center spine area work left to right gently and that will pull the entire module out the only thing you may have to do is remove the one screw that is attached to the motor wires retainer just to give slight bit more clearance disconnect motor and fan wires. Hopefully that helps

[@rcguygarage]

You just gave me an idea maybe I should do a video. 😂🤣

[@calvinwolf7107]

@@rcguygarage that would be awesome, the 4s Outcast I have is the v2 and with a 6s firma system and surpass motor, I've removed everything I can to get it out as the differential needs work but I can't get it to budge

[@rcguygarage]

@@calvinwolf7107 thought about asking a Facebook group that specializes in this particular vehicle because I know there are plenty of those and you could get your answer ASAP normally

[@calvinwolf7107]

There's been a few and that description actually sounds like it'll help, at least more than the manual did 😅

[@teslacybertruck750]

Sir this video can affect Arrma's sales 🥺

[@Schmidt3850]

Spectrum motors are junk. Buy a hobbystar motor and call it a day.

[@mrpbrasa]

Thank you so much. I just purchased the 15 dollar bearings and removed the 75 dollar spektrum motor out of my shopping cart. Great info.

[@GaveitagoRC]

I had to do exactly the same with the v1 K4 and my 3s Typhon, it's frustrating. 🤔 Such a failure can cause so much damage too.. This video will definitely help out others post release though 💯

[@alantaylor353]

Yeah okay, you've been somewhat rough, but no rougher than is reasonable. I hesitate to even class it as an "accellerated usage" type deal because many buyers will do exactly (if not more of) the same type of driving you've been doing & expect their BLOODY EXPENSIVE NEW RC to handle it better than this.! It's not looking good I fear. All of this happened quick.! Also, Spectrum gear SUCKS HARD.! There's not one piece of Spectrum left in any of my 3 Arrmas. The shortest was an ESC at 1 week & the longest was a motor at around 8 months... (got sick of rebuilding them & chucked them in the spares motor box, I've had better from a £15 Surpass motor). Unless you count the radio gear, that's all still good... Because it's been in a box for a couple of years after being ripped out immediately. Arrma need to sell all their RCs as rollers the way Hobao do & give us the choice of electronics... It won't be Spectrum.! Stay safe RC Guy you awesome Guy you, as always, best wishes from Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️.!

[@thindigital]

Ironic there's an advert for an arrma before your video with them saying designed to be bashed and hooning the thing around. Then the reality of watching your vids and seeing what the actual experience is like. It's kinda like ready meals or getting fast food, the marketing looks great, but then you get it home and have to eat it.

[@rcguygarage]

🤣😂🤣😂🤣😂 RIGHT

[@StreetBikeIke]

Exact same thing just happened to me on my 2 day old ARRMA mojave 4s. Exact same motor as yours. Unacceptable and truly infuriating

[@kevinb729]

Great video Guy. I told my son THIS is why I love the hobby because you truly can fix anything

[@HAPPYJACKRC]

Arrma again Junk out the box. My kraton 1/5 8s exb roller needed work. Out the box

[@michaelhimsworth6512]

Thanks 4 just saving me buying buying a new motor + it made me feel good fixing it 💪

[@mannygbb]

The motor is $50. Not worth the effort but appreciate the content.

[@michaelkowell7106]

Thoroughly enjoy your content, thanks for sharing the bearing repair and recommending the TRB RC replacement bearings. 👍💯

[@Killa_b_rc]

I have those same replacements bearings

[@juliemiller5740]

Looks like that are still making junk.

[@lukebaines7785]

3:26: "I feel that a hole is better than a slot". Is this still about RC? ;p

[@rcguygarage]

Shhh the KZbin gods will sniff you out

[@dub2536]

I like when u show in detail the repairs u do. TY. Happy new year.

[@rcguygarage]

👍💯 I just OVERHAULED my original big rock😳😲

[@dub2536]

@@rcguygarage Im tempted to get one as I want a 1/10 scale basher that is reliable and doesnt have issues (gears/differential etc) as often as other 1/10 scales. This is one I found online under $400. "ARRMA 1/10 Big Rock 4X4 V3 3S BLX Brushless Monster RC Truck RTR Transmitter and Receiver Included Batteries and Charger Required Black ARA4312V3 Trucks Electric RTR 1/10 Off-Road" What is your favorite off road capable 1/10 scale rc truck or truggy?

[@daviddobson20]

Well I see what am going have do is take this motor out and put in hobbywing 2400kv that I got.

[@IowaBudgetRCBashers]

I save everything. The minute ya throw it away ya need it

[@nofreerides7033]

Great job GUY… motor better than new 👍👍👍way to go… giving confidence to anyone who has this issue… love it…

[@koudaf9483]

How do you get the little red plastic thing back in under the motor? I have tried everything, but nothing seems to work.

[@mikelester5524]

How about the 3900 kV motors are those sustainable to bearing failure as well as the 3200 KV and that 2400 KV

[@country2coastadventures]

Great vid brother thank you. My Kraton just took a crap on me during a bash session. I pulled the motor and was wondering, should that motor shaft spin? If it doesn't spin does that mean that bearing is broke?

[@rcguygarage]

Just keep in mind based upon my answer I have no idea what kraton you talking about because of the way KZbin shows me your comment most of the time I'm using my cell phone so if it's the 6s yes the motor is definitely supposed to spin if it's the 4S same thing you may have gotten contaminants somehow inside or you had a motor bearing failure could have also had a rotor failure but that's more rare

[@ThePhilDEEZ]

Same bearing got roasted on my kraton 4s v2 the other day on the 3rd trip out.

[@hobbyvalentino148]

it sucks you had to fix the motor , thanks for showing us how you do it

[@mrmeseas1225]

fire fixes everything haha almost as good as duct tape

[@chrisstevensrcadventures9017]

Great stuff bud I got a lot of these motor 👍 great video guy

[@yvonthibault6041]

Thanks for the video !! I like that you took the time to show us and give us some nice detail's on the best way's to fixing these motors. Super Thanks !!

[@rcguygarage]

Glad it was helpful!

[@cstone1180]

Great content rc guy, keep up the good hard work, hope you have the kinks worked out . Have a great holliday weekend later guy 👌👌👍👍😎😎

[@rcguygarage]

WAY TOO MANY COMMENTS buried by KZbin. No notification on this one just seeing now!!!!

[@alankowalski8781]

Now you know why we wanted a center diff

[@Macgyver46]

Glad I have a spare 3200kv for my vorteks.

[@StevenYDG69]

I may have just missed it but what is the part number for the upgraded bearing?

[@StevenYDG69]

Hold up I see it in the description 👌🤘

[@lael1236]

Nice fix mate keep coming the good stuff!!

[@carlosvelazquez4649]

I'm here to be flagged. Awesome video.

[@jeremystewart1785]

Bit of a bummer on the same bearing issues still some Q.C issues going on. Still over all looked a fun truck to rip.

[@BlindByChoice00]

Im in love with my Rival mt10 ,light as a feather ...its even surpass my notorious 6s full m2c in skatepark lmao

[@ricksprings]

you gave the motor 16 to 17% more abuse than ARRMA research & development

[@rcguygarage]

😂🤣😂🤣😂🤣

[@danielbuchanan5327]

I’m a day late and a dollar short watching this video. I enjoy learning about motor repair but at the same time I wonder about the warranty on these things. Will Arrma/Horizon Hobby not replace the motor?

[@rcguygarage]

They would have no questions asked. This is a pre-production truck and I needed it fixed now not in a few days👍💯

[@danielbuchanan5327]

@@rcguygarage I totally forgot about the pre production factor. They definitely sent the truck to be tested by the right man!

[@mike-yc8bi]

You know I own a big rock an a 3s typhon my sons got a granite an typhon mostly all running 4s over the last 2years I've had to many of these to even list an a bearing failure is nothing I've ever dealt with on one of these... it leaves me to wonder if all ur issues are steaming from driving these trucks in the sand looking stuff over there at diamond dust... everyone knows what sand does to these bearings in all rc car bearings but that's my thought I hope you better luck. Also good job on these last few videos an showing some details... cant wait for mine to come... I know I love my v1 outcast 4s i can only imagine the kraton that's on its way

[@rcguygarage]

You liked the V1 you are going to absolutely love this V2 I tell you right now the videos don't get to show what I'm feeling and how much I like this car

[@mike-yc8bi]

@@rcguygarage well I got the kraton ordered cause i have the outcast tho mines very from stock having proline powerstroke shocks arrma cnc diffs it's got the spektrum 120amp an a leopard 2400kv steering rack an servo saver hot racing shes a animal an a m2c motor mount...

[@EXTREMERC416]

The vendetta bearings come with rubber sealed front bearings made in vietnam

[@rcguygarage]

Now THAT'S good to know this!!!👍💯

[@joeyfiend7864]

The hotracing steel spur is solid. Perfect fit and holds up well

[@rcguygarage]

Good to know👍💯

[@xod7861]

Off center

[@williamoleary9330]

What an awesome video. I’m super impressed with literally everything you did testing this and then the way you kept it real explaining everything. Becoming a Subscriber because of this video

[@rcguygarage]

Wow 👍💯🙏

[@martinbullla7654]

​@@rcguygarageis that the spectrum firma 120 amp ESC that's in THAT TRUCK

[@martinbullla7654]

​​​@@rcguygaragehave a 120 amp spectrum ESC in my Traxxas Hoss with the stock 2400kv Traxxas motor slowest I can get the truck to go is 8 miles an hour and I mean that's the absolute slowest I cannot get it to creep I even geared it back down to stock and it still goes 8 mi an hour I even hooked up my spare 2400kv Traxxas motor and it does the same thing and the new Traxxas motor has a clicking noise on the inside I just need some help getting this ESC sorted out I just don't understand why it won't let me go slow is it because the Traxxas motor windings come out of the motor like 3 in unlike the spectrum motors that have like maybe an inch hanging out I know some of them have like three in hanging out but could that be the reason why

[@gregganderson5479]

This video makes me really grateful that I bought a roller... planning on using a Castle 2200 KV.

[@crutch958]

Do you think the spur gear caused the motor bearing issue or was it the diamond dust??

[@rcjay2713]

I found the gear mesh straight out of the Box seems a little tight you think that could be the reason why that bearing goes? Do u ever check on new car before u run it 😆 ?

[@rcguygarage]

Sometimes I do but mostly I don't. I'm just in to run what is put in my hands and just repair what fails if anything. 👍💯