NEW Bass head Garage WattMeter is AWESOME

[@1ohmwrecker]

I got one in pre-order. Comes next month. Cant wait!

[@andruwsaudio2996]

Yes I love mine.

[@stckyjoey1]

What is the second piece for that comes with it?

[@jadsholloway]

Could you run this to the front of the vehicle or would the length of the wire throw out incorrect numbers?

[@jordanm8065]

You want it as close to your amp as possible to see what your voltage is going to the amp it won’t be the same farther away you will have voltage drop

[@georgeperez4231]

Where can I purchase one? Thank you 👍

[@andruwsaudio2996]

I'm going to run mine to the front eventually. Also it shouldn't matter wire length since all it is doing is reading current and voltage

[@andruwsaudio2996]

@@georgeperez4231 should be able to get one at bassheadgarage com

[@georgeperez4231]

@@andruwsaudio2996 My thoughts exactly. Thanks for the info 👍

[@georgeperez4231]

Where can I purchase one..Thank you 👍

[@andruwsaudio2996]

Bassheadgarage.com

[@mostknownunknown440]

When will they be back in stock? ​@@andruwsaudio2996

[@marcusperry1489]

Can you make an install video?

[@PhiMobileSounds]

It’s a straight forward install. There are a couple connections including the hall monitor. It comes with the instructions. I just hooked up two of them in my build. - Power / Ground / Remote - Speaker + / Speaker - - Hall Effect Sensor has a positive and negative that will need a wire extension. Pretty straight forward. Just make sure you choose your installation location first to so that you can make sure you have enough wire. Mine is in my amp rack I can look at over the shoulder in the rear seat.

[@SlamryCamry19]

I'm currently waiting for this to be shipped to me but apparently there is a big controversy on the wattage meter being compared to the SMD meter and which is accurate can you do a test with a clamp meter and dmm and see how far off the meter is

[@lunam7249]

the SMD is dogshit....it reads -35% LOW...it underates amps

[@SlamryCamry19]

@@lunam7249 every test I have seen on here shows the BHG wattage meter being way behind the SMD meter I don't care for SMD products they are way overpriced and dude is an arrogant narcissistic little man but if the SMD meter is off by 35% then that just says the BHG wattage meter is off by about 70% because not one single test I have seen does the BHG wattage meter read anything close to the SMD meter and the SMD meter is closer to the actual reading as bad as I hate to admit it

[@lunam7249]

@@SlamryCamry19 interesting....🤔🤔, ya the SMD super-underates amp power!!....a dmm clamped 100 volts at 10 amperes = 1000 wrms , on a SMD DOGSHIT it will read 650- 750 LAME!!

[@andruwsaudio2996]

@@SlamryCamry19 I can try. Honestly for 80 bucks I can't complain even if it is a few hundred watts off

[@yxxhoj225]

Watch out for those amp shark 3500 it caught on fire inside the amplifier almost burned my car down

[@andruwsaudio2996]

What kind of electrical did you have

[@VeezyHere]

We are still waiting lol

[@yxxhoj225]

@@andruwsaudio2996 stock alternator 0 gauge ofc it ran good for 3 years but then it caught on fire

[@iang7523]

How high does it read up to

[@andruwsaudio2996]

I believe it reads up to 100 amps of AC current so quite a lot. I'm not exactly sure on how many watts. I will have to upgrade amps to figure that out

[@Chris-B-Bassin]

​@@andruwsaudio2996Website says 20k

[@puppajo8155]

Il était obligé de brancher ça comme un dégueulasse 😢