New Mazda Android Auto Car Play Install Part 2

This is Part 2 of the Android Auto/ Apple Carplay Install.
First watch Part 1 Here: • New Mazda Android Auto...
USE CODE "KZbin" for 10% off your AA/Carplay Retrofit Kit!
PICK YOUR KIT UP HERE: bit.ly/36ph5fX
--------------------------------------------------------------------------------------------------------
Followed the instructions Here:
www.gpytmfg.com/blogs/news/ge...
Here we remove the trim pieces and Install the new AUX Hub and Cables.
This part is fairly simple and just takes time over anything.
Again do this mod at your own risk.
Tools needed for this part of the install:
Trim Removal Kit: amzn.to/2De2S9g
10mm socket: In Kit Below
socket wrench: amzn.to/2xD16bE
socket extension at least 8": amzn.to/2Ddu5Jb
Bought two parts from an online mazda dealership.
Updated USB Cables: C922-V6-605
Aux Hub Unit: TK78-66-9U0C
MUST HAVE THESE PARTS for NORTH AMERICA. WILL NOT WORK WITH EXISTING PARTS.
These are affiliate links to either ebay or amazon which help me create solid content on this channel. Doesn't cost you anything, just head to products through the above links. Thanks!
Music by Joakim Karud
If you have any questions ask them below!

[@boomtsstbahhoughahh]

If you want to skip part 1 just take your Mazda into a dealership and ask them to update your car. They billed me for 40 mins

[@condekirk4271]

Hey mate, just wanted to say a MASSIVE THANK YOU for this guide. I just did this for an Australian 2016 Mazda Astina. My USB module was right under the air con under the Mazda screen. I used the "drill" method to get it out without having to pull apart anything other than the front dash modules.

[@radism]

Just wanted to add that I used this walk-through to install the retrofit kit in a 2014 Mazda 3 which already had CMU version 70.00.100 4A N (Australia) installed. I didn't upgrade it and it works perfectly fine. Thanks a lot for the clip! Saved me a few hundred $$ 🙏🏽

[@ImSafeonSite]

Just for showing me how to remove my trim, infocentre and centre console.. This section of video has given me more information than any other I have looked for online. So I'll be subbing and doing my led's my center pad cell phone charger, led's in drink holder, and... single line led along the trim too. THANK YOU SO MUCH!!!

[@1234oclock]

Hey, I just wanted to thank you so much for this video! I recently bought a used 2016 Mazda3 s Touring, so this is

[@farrocha1989]

Great video. Just a tip for other, if your HUB is under the climate controls like mine was it helps to loosen the entire center console and slide it back to make getting the old HUB out much easier. Just search for center console removal for your car and it will come right up.

[@tiberianexcalibur]

One thing I like about the new mazdas are a lot of their parts are interchangeable with shared part numbers as well as put together the same way.

[@JonZes00]

Dude, huge help. just got mine installed. what an upgrade. Can't believe I didn't do this sooner.

[@enriqueverduzco3951]

Thank You very much for your videos. I followed your instructions as shown and it was kind of easy to complete the installation. The only tricky part for me was to route the wiring from the dashboard down to the console center bay. I just installed mine in my Mazda3 HB 2014 and it works perfectly so far. Greetings from Mexico!

[@websiteinabox]

Thanks great video, couldn't believe how easy it was in the end, UK 2014 Mazda 3. Took me a couple of minutes to work out where to feed the cable down, but taking off the side panel at the footwell helped.

[@mikep0nd]

Thanks for this! Great tutorial, 100% worth doing it yourself than paying $600+ at Mazda (I was quoted $599 + tax)

[@savydaniel]

Followed your steps, and I must say, Android Auto is a blast in my 2015 mazda 3. I opted for the firmware update at Mazda ($25), they did it with the engine on and the sdcard inside, but hey, it works. Everything works perfectly, so thank you for the instructions.

[@mathieulavallee624]

Thanks for this. Just came around to do it and it helped me alot. Already had 70.00.100 installed on my M3 2018 GT so didn't have to touch the firmware. Took about 1.5 hours, works great!

[@jvgregersen1]

Just finished and your video and Ash8's instructions on the SW install were perfect! Thank you for this. 2016 Mazda3, took about 2 hours but was actually pretty easy. I just watched the video over and over and over to make it take hat long. Could have finished in 1 hour.

[@petermohabeer3370]

I was thinking of doing the same install myself but was a bit weary about the cabling. Now that I know it's this easy, I"m definitely going to buy it now.

[@GarifullinMichael]

oh, mate ty so much for that clear instruction! I installed ease it by myself without any doubts

[@krapj214]

this was my bible for doing this install. thank you so much Greg!

[@Calypso3]

Thanks for the step by step! Everything worked. Only difference for me, is that I went to the dealership for the software install. They charged me $75 but I’d rather that than bricking my unit.

[@dennisneu8864]

Thanks so much for the video; just did this Friday night and it was pretty easy and I'm stoked to have Apple Car Play now in my Mazda 3. One note - I pulled the glove box, but didn't see the need; was able to route the cable from behind the screen and through the console pieces without having to access that area.

[@dougc1087]

Just installed CarPlay on my 2015 Mazda 3 thanks to your help. Saved myself a few hundred dollars!