If I’m honest I wouldn’t use silver line stuff to hold the door open!All the best.
@QuickBikes Жыл бұрын
They didn't last very long 🤣😂 That said I've got some of their air tools that have lasted years. The gun is fine but jaws are rubbish 😂
@redchemicalsltd2324 Жыл бұрын
Silverline....mmmm, cheap & that is about it....low quality crap😮
@RaceJan Жыл бұрын
Can't beat the pleasure of getting to play with new toys 😇.
@QuickBikes Жыл бұрын
It's going to be handy this is once I get used to it 😁👍
@johnjewell219 Жыл бұрын
Hi Jason chuck you handle away and build a hand wheel ,you can then watch what you are doing ,whilst instinctively operating the wheel.this allows you to concentrate on your line or edge .what happens with a handle you have to figure out where it is all the time and it breaks concentration Cheers John Central coast NSWAus
@QuickBikes Жыл бұрын
Aw yeah.... I can see that working 😁👍
@davidneale5821 Жыл бұрын
It would be handy if you could fit a suitably geared motor with a foot operated switch instead of the handle. Then you can use both hands to feed the sheet 😀
@QuickBikes Жыл бұрын
They do them, but they cost a bob or two. This would be an awkward machine to use on a big panel I reckon...
@davemason6273 Жыл бұрын
Ayup Quicky, was just wondering if you could put the dies on the other way round, so you can have the sheet away from the machine if ya get me?
@QuickBikes Жыл бұрын
I'm still playing with it matey, trying to learn. Trouble is the metal doesn't sit down nearly as nicely if you do it the other way. I need to try turning the dies around as well tomorrow which may work 😁👍
@basilwatson1 Жыл бұрын
some make a bolt on support, people get quite creative with their bead rollers
@QuickBikes Жыл бұрын
I can see me making a few dies on the for it in the future 😁
@colinhiggins1412 Жыл бұрын
I thought the dies needed to be the other way round. What if you wanted to beed roll a piece with a curve on it that wouldn't fit in the slot between the shaft and the frame.
@QuickBikes Жыл бұрын
The metal seems to lay flattest in the dies this way round. If it swap them its up at 45 degrees... To be fair I'm still playing around and Googling stuff, but all the videos I'm watching have it this way round... Stay tuned matey
@basilwatson1 Жыл бұрын
ummmm I know I commented here ... As I supported Jason's bead roller wheel mod and mentioned about buying a hem roller set ,,, are comments getting deleted?
@QuickBikes Жыл бұрын
Nothing gets deleted on this channel matey... It may be held for review though as I've not checked that in months. Let me go look see...
@QuickBikes Жыл бұрын
Right, I've just checked and there's nothing held for review. All comments have been published matey. If you have something to note to just add it here... 😁👍
@lardmarc Жыл бұрын
I like that.👍
@QuickBikes Жыл бұрын
Thanks for watching matey 😁👍
@mauricecasey866 Жыл бұрын
👍
@QuickBikes Жыл бұрын
😁
@itfc3 Жыл бұрын
hello buddy. quick question. what sanding discs and belts do you use and what grit as i have some welds to dress up.
@QuickBikes Жыл бұрын
I'm not sure actually matey, I'll check tomorrow and let you know 👍
@itfc3 Жыл бұрын
@@QuickBikes nice one cheers
@alanrichardson1672 Жыл бұрын
I don't like those indicators, they look cheapy Chinese stuff 😮 I'll get me coat!! 😊
@QuickBikes Жыл бұрын
Hehehe.... They can always be changed for something else that suits the new owners sense of taste 🤣😁👍
@eddiemizen3703 Жыл бұрын
Organ grinder springs 😂to mind
@QuickBikes Жыл бұрын
Hehehe... 🤣😂
@kennethsutton282 Жыл бұрын
Thank Allah you're not doing a Ducati sticky out thingy wotsit for the number plate. They look shite, like an afterthought. ☹️
@QuickBikes Жыл бұрын
That was my thought 🤣😂 It just wouldn't look right I don't think 🤔