new trick for thin pipe fabrication that welders rarely discuss | pipe cutting tricks

[@vyacheslavtimofeev_1974]

Спасибо .

[@大輔伊東-b1z]

天才ですね☺

[@seizoasano2330]

Deste vídeo eu não gostei. Mas vários de seus vídeos me ajudaram no trabalho ,tive que substituir o caldeireiro , fazer boca de lobo a 42 graus. Obrigado pela ajuda !

[@GuitarGreg1970]

Geesh, I wish I had your artist-like skill with the angle grinder, let alone the welding. Well done!

[@dfu1685]

I know! You are a Michelangelo with that welder and cutting disk! It’s clear that you have been using one for a long, long time. It’s the way I use a pencil, but you use a cutting disc. And saving the best for last, this is brilliant pipe welding design. You must be good at math/ geometry, too!

[@jodei3601]

Clever gadget 👍👍👍

[@ベレGおやぢ]

なるほど、すばらしいですね。 俺も溶接をやってたけど、多分二度とそういう仕事をする事がないから、実行する事はないでしょうけどね…

[@AlwaysHopeful87]

Nice, clever.

[@カッコマン]

2本共角度45°で切断して継手したほうが簡単で早いよ。

[@semiproactive9625]

Huge waste of time. Cut a miter to the center from both sides, weld.

[@martynpegg1483]

Kool I’ll just dd that to my art and craft file

[@Chuzhoj81]

Привет!👍👍👍

[@Berjalanterus-b6x]

Mantap om 👍

[@stickwelder]

Makasih 👍

[@ejishinjo7448]

I know why this isn't discussed with production welders.... takes to damn long. We need five of those welded by the time it took you to do one. Production welding sucks that way.

[@don8659]

I mean if you're into doing arts and crafts sure.... If you're trying to get a project done on time? No. Just cope the damn pipe and weld it....

[@Unpredictable-y2h]

What is the size of welding electrode?

[@Oracul41]

😅 Приём - Оригами 😂

[@ぽこぽこ-t4x]

こんなめんどい事せんでも両方45°で切ったらええだけやん

[@Gofkagschoice]

⛔️ STOP ⛔️ Do not repeat these actions. These are B🆘️D teachings.

[@justanotheryoutube]

Is that galvanized? Yikes.

[@hellyeaOU812]

it's china so who cares

[@galdruslock6371]

Whheeeeewww party time!

[@chasevanover]

Get the milk

[@재벌농부]

쓸데없는 시간낭비 설마 이거보고 따라하는 바보는 없겠죠?

[@lizard1574]

Когда нехер делать и времени - вагон 👍

[@Ariev]

This is a lot of work for a cope. Just cope it the normal way and you’re good to go

[@キタコレ-l5r]

日が暮れてまうで

[@gregpecqueur882]

stupide! 2 coupes a 45 degres ca revient au meme et c est plus rapide🙃

[@Tkdbar]

Hahahahahahaaaa

[@mikealext]

WHY!!!

[@아프지말자-x1v]

저시간에 그냥 용접하고말지 저러면 공장 짤립니다

[@fireworm91]

45-degree cuts are so underrated 😢 wtf is this video?

[@billjanowski4851]

Galvanized, just drink milk

[@edwardbright9434]

leave th flapper

[@chrisautrey5051]

What a time waster. Just cut a shallow v on opposite sides an weld it.

[@dfu1685]

This thinking does not allow one to think outside of the box. Mastering millions of ways to accomplish the same thing or equivalent is what makes one able to adapt when confronted with outside of the box challenges. Seriously, give it a whirl. You only have skill to gain or a little time wasted.

[@edwardbright9434]

Look all tht time wasted all he jst cut a 1/2 moon on both sides

[@dawit14401]

저거 저지랄 할 시간에 파이프 연결 소켓 판다 ㄱ 자 T자 입맞대로 다 있다 그거 얼마 안하니 그거 사서 작업하는 게 시간적으로나 정신적으로나 훨씬 이득이다