NEW TRONXY VEHO-600 ASSEMBLY, TEST PRINT AND THOUGHTS , Part 2.

[@buzzylogic]

What slicer did you use, did you find a profile for it?

[@cgrosbeck]

At 1:39 Bong is under 8' table!!!!!!!!

[@TimelessMotors]

Duh

[@HReality]

Something that large guarantee where you build it is where it will live. I noticed the braces on the sides.. IF I do this I think Ill be adding linear rails to the Z with some 2020 or 3030 for additional rigidity. Im doing a ratrig 400 now but always looking for the next project.. worst case the frame would be great for a changeover to something else later on.

[@stevedinic5682]

I have VEHO600. I had soo many problems to start this printer. It started with the loose belts and very bad design of the belt tensioners. Than, the 4 bearings on the polished rod melted down. I had problem with the power beaker and the power plug too. I replaced them. Now I noticed that at the Bowden one screw is missing and the Bowden is loose.??? What else can go wrong?? I am sooooooo unhappy customer.

[@TimelessMotors]

Sounds like you didn't assemble it well.

[@stevedinic5682]

@@TimelessMotors I did assemble by the VEHO600 manual. I have problem with removing the printing head from the x-slider . I have problem with the sink heat position. There is no information about that in the manual. Do you know how to take a part the printing head?

[@TimelessMotors]

@@stevedinic5682 just take it slow make sure everything is squared up

[@thatduckieYT]

The nonexistence of important information about this printer is crazy. So I hope I can get some from you. 😬 How fast is the print speed? (looked super slow in your video, feel like your Ender prints faster) How's their firmware? Safety features? Runout sensors? Pause/resume function?

[@PaganWizard]

I'm looking into either replacing my Ender 5 Plus, or maybe having it as a backup to the VEHO 600 2E. Is there a way to speed up the hotend??? That looked painfully slow. At the end of this video, you mentioned your dislike of the extrusions TRONXY used. Is it possible to just build another frame with 2020, and tap the holes on the 4 vertical pieces to thread the feet into?? Does this printer run Marlin, or a different OS?? Have you experimented with 3rd party upgrades, such as BTT mainboard and TFT screen??

[@MakerMark]

Ender extender sells a 500x500x500 kit for the ender 5 plus

[@redherring5532]

at that point just dont buy the printer from tronxy and just build your own, these are just large Ender 5's 60mms printing, the whole nine yards. ya get one if you need the tool. ADD KLIPPER

[@calebleach7285]

I got mine this week and put it together. Soon as I turned it on the first time a MOSFET on the motherboard blew up.

[@MikeBeaty-os1em]

I am trying to find the OEM software, profile for cura that is on the sd card that came with printer. Mine was formatted somehow...Any ideas?

[@you.got.gapped.racing44]

A 80 pound printer, that is 39kg, does this printer ship in one box?

[@bernott07]

guys leave him alone about the bong, he's messing with 3d printers that's a needed necessity !

[@ooDemiurgus]

Nice water bong. Rip one for me dude.

[@gargajo92]

Which web page you used to get it? I found one but I don’t know if is legit

[@anset3985]

I found official store in Aliexpress

[@Deluxa801]

With 1000W power source (i quess heating bed will eat electricity like a tyrannosaurus) and very cheap belted xy+hotend+extruder setup 100mm/s speed will be final for this printer. This is the biggest nonsense shit I've seen this year. Plus as a bonus there is no external mosfet for heatbed. Again i guess from comment below it is powered directly from mainboard? :D I cant believe it. What is the reason for such a big print area? ....because for that price you can have Voron or VZbot (330) in top configuration with 48V stepper drivers and hotend with +70mm³/s flow rate. It will stamp to the ground everything what you have on the table or what you will try to stand against them. Anyway thanks for the video ....hard to find info about this printer.

[@TimelessMotors]

It's a 350w

[@futuregadget_v2.1]

@@TimelessMotors Heating must take forever... My 310x310 heating bed has a 750W heater.

[@tahubulatgurihz]

i think it need mod for faster moving

[@SilvaPhotography]

This has to be the worst unit you can buy ! After i put this thing together and it wasn't to bad to do , i plugged in the power supply and turned the unit on ' ok fine i ran threw a couple settings ' ok i turn it off unplugged it from the power supply to move it into its home position , plug it back in and it did not turn on so i unplug it again only to find the 1 of the pin's from the power supply had broken off and was in the power cable so it wasn't making contact i Have sent a email to. TRONXY support with photos and they still have not responded ... make a video on how i can get my money back 😡