07-2012 Nissan Altima engine mount replacement... tools needed 10mm, 16mm, 18mm, flat head screw driver
Пікірлер: 32
@nya66joe332 ай бұрын
Best video I’ve seen so far. Thanks
@Westlyn803 жыл бұрын
Trans mount and both upper torque n motor mounts are really easy to install.
@kingchrisp1984322 жыл бұрын
So the bolt that's in the middle of the transmission mount isn't supposed to be tighten?? Is it suppose to have a gap in it??
@areidcoversongs38243 жыл бұрын
This is very Informative.. Keep uploading :)
@HathorLucas3 жыл бұрын
Well done thanks for the share #maricel canoy
@altimaV65 ай бұрын
What were you experiencing when your transmission mount was damaged? do you have vibration at 60 mph while accelaration same as cv axle vibration ? I hope to share me some info
@teddiazjr.62232 жыл бұрын
Good video and detail, what brand ratchet and electric impacts are those?
@VoyErRMANN6 ай бұрын
Nice video bud
@MichaelKlicpera11 күн бұрын
I had an engine shaking issue when trying to take off from a stop … seems like it would go into limp mode … the front right torque mount was bad replaced that .. but it’s still doing it .. but not as bad .. seems like it’s coming from the bottom .. do you think it’s the mount that needs to be replaced ?
@partsshooter11 күн бұрын
Shaking and limp home mode is more an engine or drivetrain issue. Check engine and transmission modules for codes for any correlation with limp home mode
@JoseGonzalez-ed3mz Жыл бұрын
Tanks, brother i do.
@AlohasVlog3 жыл бұрын
Hi, sending my full support from Maricel Canoy😊. You have nice content😊. Looking forward for more vids from you😃
@strawberrylensana3 жыл бұрын
Oh your really know how to fix the car my friend new year give away
@jaybreezey69453 жыл бұрын
Brother. This is a maxima 7gen. The motor mount u r replacing is hydrolic. I am doing the same but I don’t know the correct pounds specs how tight must I put it. I don’t want it to leak out fluid braking
@TheWrathJJ3 жыл бұрын
Naw its an altima I got the same car this one has got the 3.5 like mine. 7the gen maxima has the same front end as the altima or same year
@zaneorsborb70724 ай бұрын
Did u do anything with the bolt that gos inbetween the rubber had mine tighted all the way down road horrible and its not sticking up like urs as well
@quesstar26003 ай бұрын
Yes, there is. On my JXX35 there was a spacer on that through bolt ( which I assume was a factory mount ). It was NOT there on the replacement. I estimated the same amount of compression. I agree with you that it is necessary to allow some motion. I didn't notice until I had installed it, but I believe you can install it in-situ. Just hope that you still have the old mount. Otherwise, I can give you dimensions and you can make one.
@xizsv.702 Жыл бұрын
So where did you jack it up from the transmission or the engine?
@evangelinebishop80753 жыл бұрын
well done , thanks for sharing #Maricel
@JoseGonzalez-ed3mz Жыл бұрын
What year si this car, i look for spanish video but i cant find, i want tray undstend You, tanks. a question excuse me, all the screws and nuts of the support above are 18? Thank you.
@Mrdealornodeal618 Жыл бұрын
01:56 Are these same motor mounts in the 2014 altimas? I'm really curious.
@partsshooter Жыл бұрын
Check rockauto.com for matching part numbers
@GeneG-wk2mz2 жыл бұрын
This was and auto?
@nicholasalford55453 жыл бұрын
I have a 09 Nissan Maxima and it needs motor mounts and I took it to a shop and they told me 1600 and it’s about a 8hr job bs
@partsshooter3 жыл бұрын
Its a pain the ass job!
@jaybreezey69453 жыл бұрын
Brother what r the specs. Torque on that hydrolic mount. I can’t afford to brake it
@partsshooter3 жыл бұрын
Can't go wrong 20ft lbs. If you must torque it. Good luck
@jaybreezey69453 жыл бұрын
So. The hydrolic passenger side is only 20ft pound. Wow.
@jaybreezey69453 жыл бұрын
I was told. That each motor mount has different specs. Correct ?
@partsshooter3 жыл бұрын
@@jaybreezey6945 yes, they do however 95% of people don't use a torque wrench to tighten down mounts. It's more common sense feel. [Don't over tighten with a breaker bar don't under tighten with a 1/4 inch] If you're tightening the Passanger mount to frame 20ft lbs is fine
@jaybreezey69453 жыл бұрын
Thank you brother so much. Again it’s basically that one hydrolic mount. So 20ft pounds is perfect. But. I will tell him to just feel it like u say with out the torque. Not over right ok great thanx alot