Nissan Murano Camshaft Sensor Tips

[@Sweeneyboy78]

The 06 Murano dipstick in mine was trash, I could barely read the oil level causing this exact problem. Camshaft position sensor. I changed the oil and fixed the leak and the camshaft position sensor fault code went away. Mine also should an oil pump fault but also went away with oil. Good video with good info for common folk like me.

[@stuartlaw3575]

Helpful video,thanks. I find checking the oil level difficult to do on the Nissan Murano

[@Sour.gymbro]

Little trick tip. Make sure the vehicle has been off for over 15 minutes to get the most accurate oil reading .

[@davidgoretoy5910]

Nice to show exacrt location of those sensors from far prospectives and close details. Thanks.

[@aaron1840]

This was a good helpful video up to the actual changing of the part. I agree with a previous comment that some people want to see the part changed out slowly. And never use music. Subtitles if anything.

[@Desertcarcare]

Aaron Dalin ~ no doubt. As you can see ~ we walked away from producing videos for a while so we could actually study what should be done better ~ we WILL ramp up fresh videos soon and definitely take every single comment as a way for us to better help all ~ thanks a bunch -Frank

[@genekerr8064]

Great Video! Nissan 2006 Quest V6 died while driving 2 times in 2 weeks. WE had Bank sensor 1 error. Replaced it,then, had Bank sensor 2 error. Replaced it, still have Bank sensor 2 error.

[@mintycocoa5802]

Very good video learning something new every day...

[@Xtrndk]

I love the information! Great video Frank. Luckily, I've already learned how to remove those clips and cam sensors, so the tutorial on how to do so was not needed. However, others might of liked this addition had you included it. Thanks for all the help!

[@Desertcarcare]

Xtrndk...great point ! Will dial in these videos & work to improve as we progress here..rock on ! -Frank

[@robynmutchler9327]

any videos on how to change the camshaft position sensor connector?

[@Desertcarcare]

Unfortunately we don’t have it up at this time ~ I would say the biggest thing here is to ensure wiring connection/splice is done properly ~ sorry we couldn’t help more here

[@no1luhrs]

You have the absolute cleanest work shoes I have ever seen.... my work shoes do not resemble yours lol

[@Desertcarcare]

Geesh --leave to those counter folks to show up and do mechanical tip vids LOL --right on ! Thanks for stopping by !

[@jeneerose3350]

Thanks

[@mikeklusko4473]

Thanks for the tips! Great video compare to others on the same subject!

[@Desertcarcare]

Thanks Mike ! We really enjoy doing the vids and appreciate you stopping by !

[@seeker9969]

Very good job on the video, Very informative All around great job :)

[@Desertcarcare]

Thanks !

[@brookmiller878]

I have a 2007 Nissan Murano s ive replaced all three sensors myself but the same problems are there had to buy new connectors from ebay and pig tail them in seemed to work for the crankshaft sensor but not the camshaft sensors need help asap the car has a very rough start now

[@romyespinosa7651]

I would like to see how to fix the pump windshield for nissan murano2009 sl

[@elcancerynosotros.7036]

Good morning! May I have your help? My Nissan Murano 2004 180.000 miles is presenting some hesitations and sudden stop in the way at 70 miles x hr. The engine decrease the RPM, them the brake light on steady and the check engine light appear. I stopped the car, turn off the engine and turn on back. The check engine light remain on, but the symptoms disappear. Can be the same issue that you are describing in this video? Thanks a lot for your help! And, forgive me if you find any grammar mistake, I trying to do my best to speak and write English well!

[@nigellbk]

Hey Frank great video man I have the 2010 and it stalled yesterday , do you think this is a project I should take on or I should take it to a shop? your thoughts

[@2003ranp]

Are you getting a trouble code?

[@tombrahem4367]

Frank, I wanted to know about the air pressure indicator mine stays on. 2007 Nissan Murano

[@yolanikenny6407]

Are they the same as that of the Elgrand VG33?

[@Desertcarcare]

In theory yes . Double check part numbers & make sure to stick with OE parts ! Hope this helps - good luck here !

[@aguacaterodeoficiomartinez7028]

Thanks for the tips buddy,

[@cesarvallenilla8949]

Muy buen tips el del aceite.

[@fknsenditt861]

so did the car. comeback with issues or was it fixed?

[@Desertcarcare]

Fixed

[@jeanmoneytree1485]

Hey there quick question which one is bank 1 camshaft ?

[@stevejami8074]

Good job

[@michaelhorn1162]

Thanks for a great video. The oil level really does matter for these sensors. I was about 3/4 quart low. Once I added oil, the problem went away.

[@mauvevanvalleryvinz4913]

How much it would cost to change both crank shaft & camshaft sensor?

[@carljenkins5092]

I have a 2008 Sentra 1.8 engine 160k. I’m getting the dreaded P0011 code. The dealer said it needed a timing chain. I ordered Nissan parts off of E bay and had it installed. The internal engine looked great. The light came back on. It has a new crank and cam sensor in it and both from Nissan. What am I missing? What else can it be? It’s running like it did when it was new. My wife and I love this car and we want to keep it. The dealer said they have seen this problem before but not in 160 K. Any ideas?

[@Desertcarcare]

Carl Jenkins ~ tough to say here ~ call me at the garage ~ will try & research for you

[@dennisvelasquez6877]

I have a 06 Nissan Murano I have a p0011 code I was wondering where is bank one

[@johnnychumley1432]

having miss fire ..still after..change spark plugs ,, n coil packs...... help////

[@cherokeeconcrete1986]

Change the Camshaft Position sensor out Johnny🤷🏽

[@jimgoodman9070]

Hey frank 7/28/2024 4 am i just bought a 2004 Nissan Murano 3.5L v6 the guy said he replaced both of those sensors bank 1and bank2 but i noticed it is smoking little?

[@Mattgoodtimes24290]

Hi, thx for this great video! I changed all 3 sensors about a month ago as i had trouble at cold start, then it worked great, and yesterday the p0345 bank 2 error code is back! Any advice ? Thx a lot and happy new year !!!

[@Desertcarcare]

Matthieu ~ were they aftermarket or Nissan sensors ? We have seen problems with aftermarket cam sensors here, but need to confirm, otherwise need to test it to know for sure. Call ya at the garage if you need any further help over the phone ~

[@elboregojhb]

Just ignore it

[@Iheartcatz]

I have no check engine light but my nissan murano has died while driving. Everything shuts off. After a minute, im able to restart car and get home. Im so frustrated.Do u think this might be my problem?

[@johnnyplacido3366]

I have a Nissan murrano when I press the gass and start driving and stars hesitating to go . I have no check engen lights on

[@Desertcarcare]

Johnny Placido ~ tough to say without seeing & testing < you may have the beginning stages of an ignition coil that may be starting to go out or a need for a good ol fashion tune up < have it tested before you start throwing parts at it ~ good luck here

[@briancollard6825]

Hey I was wondering if you figured out the problemI have a 2007 Nissan Murano SL I have changed the oil did a full tune-up replace my whole exhaust system and every O2 sensor. My car tries to die if I turn the AC on and does not run well at low gears if I stop giving it gas

[@W.Khairi]

@@briancollard6825 & Johnny placido , Have u tried cleaning the throttle body, When clogged up it usually creates hestistion or even stalling at initial take off and during stop and go situations, also it is related to AC operation as well.

[@smms1276]

What kind of rachet wrench are you using? Got my eyes on some tekton extra long ones 👍.. Got A get me some

[@angelangel8510]

2005 Nissan maxima no lights on jerks when I slow down to 20 just got the Val body done and changed crankshaft position sensors and camshaft

[@smms1276]

WELL DONE 👍 👍

[@osbornjude709]

Pls where do I get all the 3 sensor to buy

[@guybrooks3480]

Should I bother hooking up to a machine , if he wants to change all 3 anyway ?

[@Desertcarcare]

Good point. Test and verify either way

[@guybrooks3480]

Will do , and thank u bruh

[@Desertcarcare]

The total cost with Factory OE sensors installed right around the $250-300 ish mark. Did you need a garage recommendation near you ?

[@jennymaldonado3955]

hello am jenny i have a question...i have a nissan murano 2005... first time owner of a car in general..so am learning. my airbag light is flashing and my horn went out also i took it to nissan which the putmy car on the machine and it gave 5 different problem according to them so i went ahead bought the parts so my bother can fix it turn out out of 3 engine mount i need 1 everything else i have replace and nothing seem to work nissan wanted to charge me 3,500for all the problem.. can you please explain to me what cause that or post a video of what to do when this happen....thank you

[@Desertcarcare]

Jenny Tirado ...I suspect the horn & air bag related to a clock spring fault. Email me details & I will video. Hang in there ...all good . -Frank

[@jennymaldonado3955]

can i have an email am new to your channel..thank for the reply

[@Desertcarcare]

Jenny Tirado [e-mail]

[@ismailwajih1952]

You need to change the angle sensor. It's inside the steering wheel just in the center. It's in charge of all the problems you mentioned. I had the same problem with my Nissan Armada !

[@johnkimmel2612]

Does the Autel unit you are using have pids for both bank's camshaft sensors and vtc solenoids? What I do after checking for proper engine oil level is to put all 4 on screen and look at duty% of solenoids each and deg.of advance of timing of each. When one of the phase sensors is bad you will see no change under load in drive with foot on brake(aprox.1200rpm).

[@Desertcarcare]

John Kimmel ..great question. The Autel has 2 channel scope ability & we typically don't have an issue with that setup. We can go to our SnapOn Modus 4 channel if necessary..great input ! Thanks

[@linobancain1531]

Hi Frank, my nissan murano 2007 Awd with 130K have the same problem in your video. I lived in Las Vegas do you have a branch here?

[@joel.tlumayi9813]

hello i have a nissan murano which is having high idle and keeps on going up and down

[@CustomerReviews123]

I have a Nissan Murano, the engine light came on, it stall on me one time. There seems to be a little vibration and missing with the engine. I took it to a mechanic they told me one of the cool needs to be change, the engine light came off when I took it from the garage. But the following day while reversing, I noticed the engine light came back on. I also felt a vibration. What you think is the issue?

[@billyoungblood6901]

I have a 2006 missan murano 3.5 litre engine it started missing it runs for a couple minutes then dies and have to let it sit for about 15 minutes it is throwing a cam sensor code po340 any ideas greatly appricated

[@billyoungblood6901]

It also has has multiple random miss

[@Desertcarcare]

Best to have proper testing performed ~ you may have a few things going on here ~call us anytime if you need a referral of a great garage in your neighborhood

[@MrPutzdad]

So how does low oil level induce a cam sensor issue? How does that actually work?

[@banquetoflaughter3753]

So helpful 🌟🌟🌟🌟🌟 It worked out for me.... But what if it's continues what should I do?? 🙄🤦‍♂️

[@NLWinstie]

I changed all of the camshaft sensors and crank sensors but i still have an issue with the engine light and slip. I cleaned the connector and it still is there. Before the sensors came on i actually serviced my car and then after that it came on when i parked. It takes a while to start as well.

[@rayonwilliamssportsandfun2106]

Give an update on 2013 Nissan Altima plzzz

[@margaretshepperson2441]

How much would you charge to replace these sensors?

[@JesusQroz92]

what is the simtoms if the sensor are bad.

[@DAN24938]

where do you go to get the parts?

[@Desertcarcare]

Daniel Day ..Nissan dealer the best bet, however, here is link for Dorman Aftermarket Parts if cost is a factor : www.partsgeek.com/gbproducts/MC/6738-07208146.html?MC&+Nissan+Maxima+Camshaft+Position+Sensor+Dorman+Right+02-08+Nissan+Camshaft+Position+Sensor+03+06&PartsGeek+Google+Base&gclid=Cj0KEQjw6uO-BRDbzujwtuzAzfkBEiQAAnhJ0K1WhgYyKE77xKMqZWIN69BdGGC2jLbaU9nGar-QSNoaAsQD8P8HAQ&ad=47433949932

[@ebrucato]

@@Desertcarcare so many after market options... how do you chose which after market brand to buy here. I need/want to buy all three sensors to fix codes p0021, p0011,p0345 ... 2011 Murano with 160K miles... does have hard time starting..

[@thelifeofhakeem]

I have a question about a 2006 G35. A mechanic did some work on it last year and since then my parking lights don’t blink when I lock and unlock. He claimed he changed the body control module. And replaced the immobilizer. Any help will be excepted. Thank you sir.

[@rubencastaneda6788]

i have 2014 ford focus se am having the same problem with the camshaft sensor i replace them and is still giving me the same problem can you help?

[@Desertcarcare]

ruben castaneda ...ring me at the garage..do my best to walk you through over the phone~~Frank

[@MillennnialGod]

where is the crankshaft position sensor located on this car?

[@pollydor07]

Thanks

[@linalmq]

I have a nissan Micra k12.. How many camshafts is there and how many crankshafts? And where are they in the engine?

[@kosieS]

Hope you can assist. I have a 2006 Nissan pathfinder. Droe in snow and then my slip, abs, VDC off, 4x4 lights went on and the 4x4 picture showing wheels went blank. Any idea guys?

[@Desertcarcare]

Kosie Schumyn ~ call us at the garage for this one ~ tough to say what this could be without testing

[@mw7540]

I have a 2000 nissan maxima. And she is having a cold hard start, and when the car is completely warm up it stalls. But this only happens when the engine light is on. Once i clear the code the car drives great. What could this be?

[@maddrichstaks7787]

Greetings Desert..Rich here quick question I'm currently running 06MaXse 5At..and I'm having a p0731..car drives quite fine..I check transmission fluid it's all good..wires all good..would the transmission speed sensor cause that code..thanks In advance..any info would be greatly appreciated

[@1milazzo]

Instead of making a highly edited video with house music in background (during most important part), why not just show how to change the damn sensors properly. You basically made a music video with a mechanic shop theme...

[@Desertcarcare]

1milazzo ...yes sir. No doubt. Great point. As I progress with these videos..definitely will dial it in. Great point. Well taken. --Frank

[@tonyrodriguez849]

@@Desertcarcare Your video was fine with nothing to change. The music was not even on that long, and the footage of you changing the sensors was "SELF-EXPLANATORY"...you can't please everybody. Thank you, as this helped me out with my problem on my Murano.

[@eddytv948]

My cam shaft sensor doesn't have spark on the supply wire

[@eddytv948]

2009 model

[@dudleylarocque5060]

my murano 2005 starts but dies when i accelerates and will not starts back untill few hours , i change all sensors cam and cranksharft , need some advice

[@Desertcarcare]

Dudley LaRocque ..ring me at the garage for help & tips. ~Frank

[@dudleylarocque5060]

Thanks frank Can you leave me your number ?

[@Desertcarcare]

Dudley LaRocque 480 726 6400. All good .

[@dudleylarocque5060]

Thank you , what is your opening time ?

[@Desertcarcare]

Dudley LaRocque ..ring me around 11am..all good.

[@hammerhead19able]

Thank you. Changing out as a set sounds good.

[@michaelthompson1626]

Just swooped out bank 1&2 camshaft sensors on my 02 nissan altima 3.5....she runs worse and clanking sound, now codes read advanced timing. How do I relearn timing control?

[@sonnynguyen7202]

Hey frank I have a 2014 Nissan Pathfinder 3.5 platinum 4WD I have a stalling issue due to cold weather when it gets to -10• C and no check engine light came on and no codes came up what could be the problem I went to Nissan dealership and they couldn’t locate the problem my vehicle is at 170 thousand Km please help me out

[@juanhinojosa9784]

I have 07 murano that when i put it in Drive i press the gas pedal all the way to the floor and it bearly moves foward the fast ir will go is about 5 miles per your and my rpms stay around 1000..... what could the problem be

[@Desertcarcare]

Juan Hinojosa ...check that throttle, otherwise ring me at the garage anytime. Good luck ! ~Frank

[@juanhinojosa9784]

Desert Car Care thanks for the prompt response..... May i have your digits to give you a ring

[@Desertcarcare]

Juan Hinojosa . ring me tomorrow am..480 726 6400

[@juanhinojosa9784]

Desert Car Care good afternoon frank, i have a question does a 2009 cvt transmission fit my 2007 murano.... or does it change to where i cant use it....

[@Theking-in1in]

I got the same problem did you fixed it

[@bobbyali8940]

When u drive car on the low speed car runs fine but when u give a speed tittle bit its start to slip the transmission

[@Desertcarcare]

Bobby Ali ~first things first ~ Check that transmission fluid level . If low ~ refill to spec & repair the potential leaks. Otherwise you may have a shift solenoid or internal transmission fault. Where are you ~ I can recommend a transmission shop by if needed. Good luck here .

[@eduardobramont326]

Please I have a 2006 Nissan Sentra and I started to hear a bump sound from inside my fuel tank I want to know what is it. Thanks

[@alan4sure]

A small animal may be trapped inside.

[@antocarva94]

merci beaucoup

[@caspernotsofriendly1803]

Frank my man, I have a 350z 06 3.5 and it too popped a P0021 crankshaft sensor. so i fleaned both VVT sensors and replaced both bank 1 and 2 camshaft position sensors and cleared codes and it keeps popping back up. the first time it happened both codes P0021 twice and P0300 twice came up i did manage to clear for good the p0300 misfire but cam sensors i cant figure out why or why not. can you help please

[@Desertcarcare]

Denny Christensen ~ring me at the garage ~ do my best to help !~Frank

[@caspernotsofriendly1803]

@@Desertcarcare ok well im going to do another oil change sense i just remembered i used a additive used for getting hp back. after looking at the fluid/oil on the VVT selanoid it showed copper flakes in it. this could be clogging up my VVT but not positive on this yet. This car has many issues including rear drive axel or wheel bearings or bushing shot and a 2000.0 crap clutch that some idiot installed in Kirkland washington and only put 2.5 qaurts of oil instead of 3.5 and could have lost life of the clutch it self. I look you up at the garage my friend.

[@fontanaofyouth]

Why does my 2009 nissan Murano engine click after it has been turned off?

[@fontanaofyouth]

Also..camshaft sensor error came when i took it to Advance auto parts to have it checked.

[@keithjames1682]

I have 05 Nissan maxima and I am getting code P0021 but I am able to drive around okay .I do have a rattling noise for a quick moment when I shift or start up my car. Is this related or is there something else

[@Desertcarcare]

Keith James ...reach out to me at the garage for this one brother ~~Frank.

[@timmay663]

Cam sensor, 0011=1side 0021=other side

[@peterdamisa5153]

Please i need your help on this: my engine was drop for the purpose of changing pisting and ring. after the engine was fixed and mounted. i discovered oil leakage from gearbox. The gearbox oil seal was immediate replaced. The oil leakage resurface after driving the car. the seal has been change for the third time it seems the problem refuse to go. please any advice.

[@Desertcarcare]

peter damisa ...using a "dye" in the system along with a UV light may help pinpoint. If you are talking about the rear main seal ..make sure crank surface where the seal is seated is not etched or scored. Let me know how things turn out for you. -Frank

[@brothareddi]

Is it okay for me to call you today? I have a question about my 2009 Nissan Murano

[@Desertcarcare]

mario redd ..sure. Sorry for the delayed response~~always on Twitter @urmechanic for quicker response ~~send a quick vid there w any questions EZPZ ~Frank.

[@brothareddi]

My wife has a 09 Nissan Murano and it stalls. At times the RPMs doesn't move past 2000. I put the paddle to the floor one time and it didn't go anywhere. I heard a grinding noise under the car when hitting the gas. The codes are P0420 and P0430. It's like it not getting air or oxygen to the engine. Thank you in advance

[@Desertcarcare]

mario redd .. very possible a clogged or restricted catalytic converter. Call me at the garage anytime~~get it tested before throwing parts at it so key. ~Frank

[@billyjames6084]

My 07 murano hesitates when accelerating. Code1721 came up speed sensor. No SES light is on. Sensor is $200.am I out of $200 if it doesn't fix the problem. That was he only code from diag.

[@mrweisu]

Those three sensors are expensive! Do people really replace all three together?

[@thatolefu123]

My 03 have the same symptoms:stalling,lack of power,slow acceleration ..but NO CHECK ENGINE OR SERVICE ENGINE LIGHT

[@MrDoomzy]

My mom has a 2005 Murano and it’s reading u3fff. She had it read by advanced auto, they told her to call the dealer and she did. They want to charge her $110 for them to diagnose.. somebody please help

[@GoverNorJackson-zu8or]

I have muno and won't stay running

[@Alureals]

Hello my husband replaced all three sensors all OEM. 1 camshaft was new the other used and the crankshaft was used. Now were getting the P0021 code, we have spent soo much money in repairs and we don't want to buy anymore parts unless we can be sure what the problem is. I've read that sometimes its just a bad camshaft, what should we do to eliminate which part is really defective i.e cam crank or ivt solenoid.

[@Desertcarcare]

Alureals....best to discuss this one over the phone. Reach out 480 726 6400, and I can get you answers ! -Frank

[@Alureals]

Okay I will tell my husband to call you. He will understand the mechanic talk more. LOL

[@messigodoy]

how much would it be if i take it to my mechanic ?

[@Desertcarcare]

Miguel Godoy ...expect to pay $290-$350 with the proper testing included. (Nissan parts)...Make sure to check those connectors for oil ! Good luck brother-Frank

[@messigodoy]

thanks and i would let you know how much they would charge me

[@adeniranolayinka4608]

Why on the motion and accelerating, the car will just stop accelerating until you put it in neutral off and then it back before it continue working

[@2003ranp]

Just buy a sensor with a lifetime warranty as I did 9 years ago. I just went to Autozone last week and got a new one at no cost. The sensor lasted 9 years.

[@hierbabuena3136]

Hello. I have a 2007 nissan murano i had the service engine soon light and car kept shutting off went to auto zone got code p0340 replaced both cam shafts and car raned fine for 2 days but the code came back on. I just keep getting code p0340. Took it to 3 mechanics and all they did was change camshafts. Should i replace them again and crankshaft as well with original nissan or hatachi sensors?

[@Desertcarcare]

Nutz Mel make sure they review waveforms & capture glitches. Cam & crank sensors common ~~go with NISSAN ~~make absolutely sure they test for faults & not solely code reading ~~Frank

[@Desertcarcare]

Both cam sensors & crank sensor all replaced together if one defective ~~good policy to do them all here 🤜🏼

[@hierbabuena3136]

Desert Car Care Will do. Thank you Frank!

[@Desertcarcare]

Nutz Mel ~~good luck here brother ~~here if ya need help no worries.

[@kristynaszekely7288]

I had my 2009 Murano checked Friday and 13 different codes showed up

[@Desertcarcare]

Kristyna Vickers make sure battery connections are good. Also ensure fuse center is not an issue. Call me at the garage if further help needed~Frank

[@kristynaszekely7288]

Ok what's the number to call you

[@Desertcarcare]

Kristyna Vickers www.desertcarcare.com/

[@NFLYoungBoy223]

Desert Car Care wow your a good man

[@namechane1758]

Show the wave form

[@isaakenns1310]

Hey my 2004 nissan maxima is running great but is smoking when i rev the engine. If anybody can help me out with that i would appreciate it.

[@alan4sure]

Still smoking? 4 yrs have gone by....

[@isaakenns1310]

@@alan4sure sold it the way it was

[@boots7859]

One thing that needs to be mentioned regarding replacement sensors. I replaced these about 8-10 years ago, and just replaced them again last week. Getting under the hood, and was all sorts of oilin/around both sensors. After pulling them out, did a double-take when comparing to new replacements. Old ones had no o-rings, new ones did. Well, I know who the dummy is now... But I'm sure I didn't remove the O-rings on the original replacements, and I always check packaging. I'm assuming the OEM ones must have had them, not sure why I didn't catch when replacing the first time. Just keep a look out. And BTW, this time I replaced both cam sensors as last time, however was still getting P0340 error afterwards. Since its got 150K on it, I replaced the crank sensor, and no more problems.

[@jahazielavitia2371]

Hello guys, quick question, when replacing the icu on a 2008 altima do i have to tow it to the dealer to get reprogram? my friends icu got corrosion from the battery and is all damaged.

[@Desertcarcare]

Yes. You may find alternative tricks & tips throughout the Internet to avoid this, however, flash programming will absolutely ensure all is reliable with the air/fuel management system. Good luck !

[@wiscofun3028]

Tip #1 was don't replace parts that are okay. Action: we're going to replace all 3 sensors even though two of them are fine!!!!

[@Desertcarcare]

WiscoFun < good point inserted. We made the assertion based upon the age of all 3 and the common failures that can occur thereafter ~ if you have one failing ~ it is certainly your choice to replace what is only broken |failing at that time . If you were to come back with the same symptoms months later , you could argue why do I have the same concerns/symptoms and furthermore why didn’t you advise me of the aged other related sensors that could have been remedied on the first visit after a costly tow and missed day of work. Use your judgement with what you feel is right for you as it is your ultimate call on what you decide to do. Our goal here is to inform folks of options and declare some of the real world pattern failures that they may decide to completely avoid, of to which some may decide to not bother with a headache that could be looming .

[@Planet_Shel]

@@Desertcarcare I agree, because if I wouldn't go ahead and replace the third sensor guarantee you 6 months later it would go anyway. Better safe than sorry LOL

[@Mabeylater293]

Like other 3.5 Nissans it's burning oil. Other issues: timing chain, cvt transmission, subframe rust. These cars are junk!

[@Desertcarcare]

TruAgape1234 ...indeed. The list can go on. Thanks for the input !

[@TheRebuilt1]

If by junk you mean a car that can run over 350k miles then yeah. The cars are as good as their owners. Oil, coolant, and transmission fluid change on schedule and car should run fine. No major problems on my daughters 04 Maxima with 357k miles on it.

[@mrcrux213]

Nissan Quest 2006 a 3.5 . Give me a engine light for one of the sensors and some time take too long to star. I put the ob2 computer but don't want to replace parts for code. 😉

[@AramK]

My p0340 always comes in if my oil little less. Since those damn muranos burning oil like crazy. Complete junk cars, but I managed to hit 203 thousands on original parts lol

[@audioamateur]

what happened at 203 thousand miles?

[@Desertcarcare]

Understanding Nissan can be expensive ..here is a link for aftermarket Dorman Brand ( please verify your correct year ; this may not be exact for your vehicle) through Parts Geek. Hope this helps ! -Frank

[@DAN24938]

i have the o5 model

[@margaretshepperson2441]

i have a 2009 Murano

[@Desertcarcare]

Awesome! How do you like your 2009 ?

[@margaretshepperson2441]

Love it. I just got to get my Air Fuel Sensors cheater than dealer cost

[@LosMancosenWarzone]

I have 07 Nissan Tiida and I am getting code U1000 Can Area Network lost communication

[@Desertcarcare]

Francis Marte ...you need to ensure all ground connections are good as a starting point...let me know how it turns out ~~Frank

[@LosMancosenWarzone]

All ground connections are well connected

[@aostwaldgm]

Desert Car Care but

[@rafishaikh3598]

RAFI HAD TOYOTA CARS FOR YEARS & hardly anything goes wrong with TOYOTA CARS. ALL MY TOYOTA CARS RUSTED FROM NEW ENGLAND WEATHER. MECHANICAL WISE ALL HAD LASTED GOOD 15 years or more. FIRST WAS TOYOTA CAROLLA 1.8 Liter engine MAINTENANCE IS KEY TO A RELIABLE TOYOTA. 1. Put BRAND NEW BATTERY- EVERY 4 years. 2. Changed CAP, ROTORS, SPARK PLUGS & IGNITION WIRES 60, 000 miles. ( even though it is early preventative maintenance) 3. Threw in FRONT BRAKE PADS 3 years HALF or less worn pads ( even though it is early preventative maintenance) 4. Would remove TRANSMISSION PAN ( so many 10 mm bolts) CHANGE FILTER of transmission), clean pan. 5. Radiator COOLANT- 40,0000 miles ( off course, ADD 50/50 ready MIX COOLANT). 6. Not last or least all belts of vehicles 35,000 miles WAS NOT AFRAID TO HAVE MECHANIC DRIVE , and ask.. If anything missed besides oil changes etc LIKE RAFI SAID, BEEN BLESSED WITH SUCCESSFUL TRIPS MAINE to TORONTO, CANADA & QUEENS ( New York ). MILLIONS OF TIMES. OH ! What TOYOTA CARS, made with PRECISION AND ACCURACY. RELIABILITY is the RESULT OF TOYOTA PRODUCTION. RAFI MAINE USA

[@JudeDude409]

DO NOT USE AFTERMARKET PARTS FOR THIS

[@ralfsautomotive]

By what logic do you justify Changing all 3 Sensors when only one is failed?? 60 bucks for the Crank Sensor and $75 each for the cam sensors. You guys must have a gold mine where you're at on extremely uninformed customers. That is just Nuts, a rip off in mild terms. Advice the customer let them make the decision! I always change the one that is bad and not guess whether or not the others will fail soon. That is the silliest thing I have heard. A Year from now if the other one fails it can be addressed then. You obviously know how to use a scope and also know that this is about a 2 minute test so why bother replacing all sensors at once.

[@Desertcarcare]

Ralf's Automotive Diagnostics & Repair ~~great points. Options always given no doubt as we advise & they decide. Thanks for stopping by !

[@Desertcarcare]

oops. Here is the link : www.partsgeek.com/gbproducts/MC/6738-07208146.html?MC&+Nissan+Maxima+Camshaft+Position+Sensor+Dorman+Right+02-08+Nissan+Camshaft+Position+Sensor+03+06&PartsGeek+Google+Base&gclid=Cj0KEQjw6uO-BRDbzujwtuzAzfkBEiQAAnhJ0K1WhgYyKE77xKMqZWIN69BdGGC2jLbaU9nGar-QSNoaAsQD8P8HAQ&ad=47433949932