Nitro engine tuning help 1. This is a basic tutorial that aplies to all nitro engines.
Пікірлер: 204
@atomicspiderpig17 жыл бұрын
nice instructions i wish i had a 25 like that
@007foppe14 жыл бұрын
i only dont understand 1 needle there are 3 but there is one close to the air filter with a spring on it wanna know where that one is for
@seekeroftruth6915 жыл бұрын
ok where do i set the needle's to begin with? i missed that part
@AdamDiddy14 жыл бұрын
Best R/C Nitro tuning video on KZbin I've seen so far. Seen about 20.
@Pyr0Maniac0116 жыл бұрын
Im just takin a guess here, is ur car suspension to soft?
@KodieCollingsGaming12 жыл бұрын
i wonder how many people's problems were solved at 00:19 "Fill the fuel tank" lol
@2122nicholas17 жыл бұрын
does any one have any advice my car start but when i put it full trottle it will not move and the engine make a noise like it is dieing
@APAP351XY12 жыл бұрын
hey all when i drive my car it will cut out n stall i have tried various solution but doesnt seem to do much plzzzzz help
@Master190613 жыл бұрын
2:31 his voice breaks lol
@owens1010115 жыл бұрын
hey mate i need YOUR help... my nitro rc car cuts out at full throttle no matter what i try... could i use instead of 25% nitro fuel... shall i use 15% or 20%... i tried altering the carb thing it runs perfect just as i say it cuts out at about 80% throttle... thanks any help much apreciated :)
@jakegwilliam16 жыл бұрын
it is a bad glow plug, even though it glows it only glows when the ignitor is in, when the engine is running the glow plug still glows even without the ignitor in,just get a new plug, also if they blow quickly richen both needles 1/8 turn.
@lankeylively14 жыл бұрын
@iamthewalrus026 you have to lean up the mix abit because its pushing tomuch nitro through and prime your car first by putting you finger over the exhaust when not running then try starting it without the glow starter and do so for 10 secs then put glow starter on and it should be fine when u start it . P.s. only try turning it over 10 secs at a time due to you can break your starter gerabox
@SamThredder16 жыл бұрын
i was making reference to the stereotype that canadian people pronounce 'about' and 'out' like 'aboat' and 'oat', respectively. me making this jibe about the canadian accent was fully called for, as you made a jibe about the english accent. there. HBDH stands for hellbent diehard, its my band! i think i prefer HAIRY BASTARDS DO HEAVINESS actually haha and for the record, i went to school until i was 16 like everyone else in england.
@bighunt0813 жыл бұрын
The only thing he didn't go into with this vid well is idle needle which is prolly explained in another vid anyway.. But for those of you who are asking on this page.. If your rc car is trying to take off while it's just sitting there then ur idle needle aka the unspecified third needle, is too high. If ur rc car is new you shouldn't have to adjust it much.
@tylert36016 жыл бұрын
check ur carb. mine was doing that and i took the engine out. when i pulled the fuel line off the carb there was some gunk clogged in the fuel intake nipple. i only found this out the other day and im still putting it back together so i can't tell u for sure if that was the prob. i told my local dealer bout that and he said that could have been the case.
@dazzlerby16 жыл бұрын
i just got a new thunder tiger car and couldn't get it started after i adjusted the needle valve according to the manual, it turns out that when i screwed the needle valve all the way in then turned it out the correct number of times, the end of the needle broke off & clogged it up proper, have a look at yours if you've adjusted it much
@mazpr202512 жыл бұрын
This is crazy, proper way to tune is with a temp gun, or onboard temp controller (those that will record Hi/Lo temps are better). Tune according to track conditions, what works on loose ground is not the same as asphalt (never ever). And make sure your stop screw is set 1/8!
@nichlasz16 жыл бұрын
can someone help me? my nitro rc car is a 4wd and the back wheels dont move...the cylinder shaped thingy came off where u put the drive shaft in..when i tighten it it still comes off anyone know what im talking about? the thing that looks like (()) and the drive shaft goes into the middle
@sladeoss16 жыл бұрын
umm maybe ure piston or sumin is like bent or damaged just say ure engine or as u said when u let throttle of it sounds like a hammer hitting metal maybe because when its fully on its not hurting it but when u let it go it hits somthing? if u r in aus take it to toy world they rock!
@FunnyHacks15 жыл бұрын
WoodyW123, tell you what. I'm not familiar with how the servo will be connected to the throttle. But if it's exposed, or you can get at it, disconnect the servo from the throttle on the engine and see if it still revs up when you start it. My hunch is that it won't, and that you will be able to control the revs by directly manipulating the throttle on the engine. If anyone knows better than me, they are welcome to speak up. :)
@noidle2215 жыл бұрын
I have a GS Racing Avenger MK II and it only has a high-speed needle, ive checked all over the engine and i cant find an idle-speed or low-speed needle. does that mean that its been factory tuned, and i only can control the high speed? on does the one needle do it all? i have a kyosho on road petrol car and it has an idle speed needle, so im confused about my other one. do you know anything about this? (i know youre not from GS Racing, but youre pretty knowledgeable) thanks
@jacobleewalker15 жыл бұрын
they do tune the enginge..... for the break in process its your job to tune it to how you want
@RIPje36514 жыл бұрын
when i start my nitro engine.. it runs a few seconds then it shuts down... any1 knows how comes?! when i stay stationair it runs for like 5-10 secs.. when i hit gas it shuts down imediently.. (sorry for my gramar, not english ;)
@SamThredder16 жыл бұрын
its called the english language, learn to speak properly and you might just appreciate other DIALECTS. ever heard that word DIALECT? you probably pronounce the word OUT as if it was OAT. this is called language. english people dont say TOONING.
@razer100017 жыл бұрын
yeah, I'm a first year nitro/pro-performance rc car enthusiast and this helped alot, my traxas nitro rustler(2.5 engine as in most traxas of that gen.) came with a video that talked about the high speed but not nearly this deeply. Thanks alot!! =D
@tittytwister525117 жыл бұрын
oh right, errm i dont know then mate if you have bourght it locally, i would take it back and tell them. but if you bourght it on the net i would email them and ask them. sorry mate
@suzukiholdenman13 жыл бұрын
Nice, I had a RC motor sitting for a few years and it seized there was ne way to pull start it because it was locked up frozen, so I took the glow plug out put a small screw driver on top of the piston and smacked it really hard with the hammer, and it worked! Hasn't run better even though there is a cross shape from the screw driver on the piston haha
@FunnyHacks15 жыл бұрын
WoodyW123, I'm not an expert on nitro, but this could easily be a problem with the electronics such as with the calibration or the controls or a fault in the electronics. Does the problem go away once it's warmed up? If so that would suggest it probably is a nitro problem rather than an electronics problem. That's not conclusive, but a start :)
@HUNTYFM15 жыл бұрын
I need to know if this would work, I have got a CEN Magnum NX and it came with pre-glued wheels and tyres except the have no inserts, I was wondering if there was anyway of putting foam in them, I know this sounds really stupid but would making a small hole then filling them with that squirty expanding foam work? Thanks, Huntyfm
@locouk17 жыл бұрын
Here's a request for all you posters, if ya see spam... Hit the spam button under that post!
@frazeusr15 жыл бұрын
i have a asnmann 1/8 nitro buggy i have tuned it and is running but when i stopand it starts to tick over and about 5 to 10 sec later it stops why is this plzzzz post back i wood like to get it right thank u
@dazzlerby16 жыл бұрын
u need a new cylidner thingy but i would check on why it came off in the 1st place, i got my 1st nitro rc last week & nearly everything has fell off it due to screws etc. not being tightened up in the factory.
@weexen16 жыл бұрын
i was reccommended an ansmann virus buggy as i was just starting this awesome hobby. they cost around 190 pounds rtr or 90 pounds for the rolling chassis. that isnt bad paying 190 because the top speed is around 45mph.
@tittytwister525117 жыл бұрын
you need to adjust the carborators idle speed so that it slightly makes the engine rev more, but not so that it turns the wheels just enough to keep it running.
@DJ.100116 жыл бұрын
Hey im new to high performance rc cars. I want to get a nitro car but im not sure which one. I want to get a car that is ready to run and is under 3 hundred any suggestions. I was looking at the hpi firestorm. Is it good?
@spiftacu1ar16 жыл бұрын
I wouldn't get the xl, its just an extended version of the normal savage ss. If you really want it longer, get the savage ss, and then buy an aftermarket tvp set, it will be cheaper and better. Try fastlane machine.
@tigger0002514 жыл бұрын
hi if i take my nitro car traxx to the hobby shop will they just put iy bk to its standerd setings or proper tunne it up for me as only cost 20 qued for them to look at it so recon be beter off?
@HARJ119614 жыл бұрын
i have 2.5 tamiya xgb n wen ever u start it starts to roll real slowly but wen it hold on to the breaks its stops but i don't i just keeps on rolling is there something wrong with ma tuning ?
@tittytwister525117 жыл бұрын
lean is more air than fuel and rich is more fuel and less air. you need to turn your high speed needle anti clockwise.
@BoobyMcDoogle17 жыл бұрын
Same here but I just decided I'd go out and buy some new glow plugs and air filter oil and throw more money into it. It's an incredibly expensive and almost as difficult hobby. Go for electrics, I say.
@QWERTYXB17 жыл бұрын
i av the kyosho land max 2 but its a bit slower than usual. i cant remember if i mukd about with the settings and i just started using different fuel. do i just av 2 adjust the needle valve?
@airhogs17 жыл бұрын
Good video. Thanks for all the tips!
@tittytwister525117 жыл бұрын
turn the idle needle down so that it doesnt move at standstill and just enough to keep the engine running at idle.
@engine238614 жыл бұрын
hey, i just picked my savage 4.6 up yesterday and broke it in today when idling it just goes does any one know what i should do so that it wont go unless my hands on the trottle?
@Ninjasloth116 жыл бұрын
Im currently breaking in my engine and i've got half throttle but when i accelarate at about half throttle the car bogs and stalls ,this also happens when i brake to.Any help please !!!
@mharten16 жыл бұрын
im considering getting one but i noticed the cost of nitrotane fuel...not the cheap, so i was wondering if rc cars the run on nitrotane also run on just ur normal everyday gas?
@coolestman6916 жыл бұрын
Sure most cars now go over 35 anyways its a low truck so its probably even capable of going 60.all cars are ready to run but if u buy it new dont forget to break in your engine.
@extremesoul66613 жыл бұрын
These things are great if your willing to blow as much money on a real car as you would these! when i was into driving these I spent more time fixing the damn thing and upgrading the parts than actually driving it haha.
@JiMLiTtLe90514 жыл бұрын
yeah the stock tuning from what i go from is to level the high speed needle and the low speed, and to have 1mm clearance on the carburetor when the throttle is pushed closed. this is also the break in setting.
@tucber3715 жыл бұрын
This is a really helpful vid, but what should I do if my nitro doesn't have a low speed needle? Maybe i can't find it but maybe it doesn't have it! Is this a problem? I've got a Nb16 t if that's any help?
@Nater3614 жыл бұрын
your backwards bud.. if your engine is hot its too lean, you need to richen it... the richer it is the more smoke it will emit. hopefully you havnt fried your engine yet
@woody411415 жыл бұрын
helpful vid and all BUT this seeing as this video was made by hpi racing, who also make rc cars shouldnt they have tuned them, themselves, before shipping them?? xD lol?
@starfishingpole15 жыл бұрын
me and my freind were tuning our rcs and i told him to turn mine an 8th and i was watching and he turned it all the way to the fucking bottom i think he fucked my engine
@Pyr0Maniac0116 жыл бұрын
Im just a newbie at this nitro stuff but im gonna try answer using my knowlege from sleds and quads. Maybe your car is running to rich and it 'bogs' so try make it leaner
@mattio7917 жыл бұрын
clean your air filter, get a new glow plug installed, and watch this video and follow it again, and if there are ever fumes that burn your eyes, lean it out a little
@spiftacu1ar17 жыл бұрын
What are you smoking? He asid the engine should always have blue smoke at top speed. FYI: that means its rich. He went lean only for a little bit to show what happens.
@theMUFF1NZz12 жыл бұрын
@MKerror the same thing happened with my gv dominator. I believe it's because the engine is new. After breaking my engine in it became alot easier to pull.
@samlakes14 жыл бұрын
I've got an nitro boat and it does have the lsn and hsn but i can't tell which way round they are. The engine is a kyosho GT engine and it looks quite old.
@sims100uk16 жыл бұрын
Make sure you do less than half throttle to warm the engine up for a minute or two, you can also put needle up a little to stop it cutting out when you brake
@BFassassin16 жыл бұрын
I have a Revo 2.5 that I cant get started. Last year I found it very difficult to get the right setting but now I cant even get it started :( What can I do???
@BostonCeltics14715 жыл бұрын
Dude i fixed mine. It was a faulty glow plug. Fixed it everything is fine. And my idle was too high, lowered it and its working fine. TMAXX OWNZ ALL. Forget the savage!!!!
@mitchell893415 жыл бұрын
thats sounds like the one way bearing when it happens...slowly pull it up, and hopefully it should catch...once it does pull fast. it may not work tho
@Triv1umxxx16 жыл бұрын
I got a Traxxas T-MAX and the clutch burnt out. Cant be bothered to fix it neither. It wasnt that good anyway to be honest. Good for jumping though.
@norm4392016 жыл бұрын
I cant get my idle to come down! HELP Please lol.... My thottle trim is set a minium and its still to high. im gonna kill my engin.. Savage X .. Anyone?
@BostonCeltics14715 жыл бұрын
I have a traxxas t maxx 3.3 with no reverse. When i drive it to full trottle and go into idle position, the engine just turns off. Plz someone tell me wat to do.
@hoffman99915 жыл бұрын
i have 3 needles on my hsp tornado, high speed (the big one with the fuel line) only under it, and one on the throttle thing, what one is what?
@DJ.100116 жыл бұрын
i am going to the hobby shop today i am gonna look at the firestorm, rustler, and i heard they have a used brushless emaxx that would be good to
@2122nicholas17 жыл бұрын
i have tryed all of this but my engine still shuts down when i leave it to idle. i even riched high speed and low speed but it still shuts down.
@2122nicholas17 жыл бұрын
i have tryed all of this but my engine still shuts down when i leave it to idle. i even riched high speed and low speed but it still shuts down.
@nichlasz16 жыл бұрын
wait wait wait.. lol....i had a pullstart engine but the pullstarter broke off so i took it off ...if i use a box starter will it work? x.x
@Bobbyz18916 жыл бұрын
no you cant it will expolde the engine causing the back place to come off, nothing spectacular but you will not be able to use it again.
@coolestman6916 жыл бұрын
well cars or trucks hpi is a good brand for 300 u can get good stuff.i bought my car for 95 bucks runs 65+ mph but its an on road car.
@keithos2117 жыл бұрын
Just bought a 2nd hand truck....anyone know why it runs fast when i start it up?Im new to this so i really dont know a great deal.Thanks.
@sparts22714 жыл бұрын
i have a Volcano S30 1/10 Scale Nitro Monster Truck and when i floor it, the motor stalls... so should i only adjust the hi speed needle to rich
@codehammer1016 жыл бұрын
the savage xl is pretty beast but if ur kinda new at how these things work and need to be maintained u shold go with an savage x.
@pillajadud17 жыл бұрын
hi.,.my engine starts and stalls after about 10 seconds,,and if i hit the throttle it dies straight away, can anyone help? cheers
@2122nicholas17 жыл бұрын
can some one help me i have nitro monster truck but if i leave it to warm up it cuts out or if i try to go full trottle it cuts out.
@xRyanwasherex17 жыл бұрын
He set the engine to lean. That means there is less gas in the engine. You need to richen the fuel so it doesn't ruin your engine.
@j0mp4m4n14 жыл бұрын
So. What if my engine stops when i brake. How do i avoid that? It runs smooth on both idle and high speed. But when i try braking it stops
@norm4392016 жыл бұрын
GET THE XL !!! Its a BEAST!!! See the Vids?? Towerhobies man google it ;) Peace and Dont waste your money on anything else. :P
@spiftacu1ar17 жыл бұрын
my bad, i just finished watching, he says it should ALWAYS have blue smoke, which means both needles are a bit rich, not lean.
@Nater3614 жыл бұрын
you dont HAVE to tune it leaner.. just a leaner engine has more power.. to an extent. im betting your leaning it too much?
@13Anko16 жыл бұрын
YOU NEED TO DO IT WHEN ITS RUNNING! otherwise you will pump out the fuel, making it very hard to start the engine again.
@Nek0a15 жыл бұрын
But it still dies, also when i use the pull start i pull it and it looses pressure, so it wont take any energy to pull it why?
@TheEchelon16 жыл бұрын
Hey, waar woon je dan kan ik een paar shops voor je opnoemen. Je kan ook gwn google gebruiken hé.
@13Anko15 жыл бұрын
too low idle speed, if you brake, the carb will close completely, and the engine shuts off, increase idle speed...
@kylie983214 жыл бұрын
yes because the enging has more lubrication so its less likley to get hot and it stops the piston running dry
@spikerbrad2315 жыл бұрын
then just tune the high needle but you might want to double check cuz iv nvr heared of a engine with 1 needle
@Bandicoot80314 жыл бұрын
Try the following: High speed needle: 3½ turns. Low speed needle: 3 turns. (Based on my KYOSHO GZ15 2,5ccm)
@kingelmo11216 жыл бұрын
reset the HSN to 3.5 turns out and the LSN to 1.5-2 turns out, PM your email and i will help you from there
@Crazylogie16 жыл бұрын
lol I have a savage also maybe 65Mph maybe not even that fast
@norm4392016 жыл бұрын
For A basic Savage X RTR and all you need to run and maintain youll spend 700 TOPS Thats about the base.
@ritejert16 жыл бұрын
u use the idle needle if the car moves and your not touching the throttle, thus the name idle needle
@DJ.100116 жыл бұрын
you may need to adjust the throttle linkage for the cutting out. i dont know about the smoke though
@DJ.100116 жыл бұрын
thanks i want on ofroad car that geos at least 35 mph is the firestorm good i think it will do 40mph
@ThomasCaraccio16 жыл бұрын
pushing out alot of smokewhen at high speeds just means the hih speed needle could be set too rich
@MrWhizzo16 жыл бұрын
Eighty miles an hour, really? Was that in the trunk of your parents car leaving the hobby store?
@NirvanaRox4Eva13 жыл бұрын
with idle, do you turn it down, so the wheels dont turn at all? or so they are spinning slowly?
@bracketracing15 жыл бұрын
what needle do i need to turn if i still have gas coming out of the exoust please help me
@2122nicholas17 жыл бұрын
hi i took it to the shop they tuned it but if i put it full rottle it still will not move.